2017 MITSUBISHI OUTLANDER PHEV Service

ScreenCauseSolution (Reference)lThere is a fault in the tyre pressure moni-
toring system.l Refer to “Tyre pressure monitoring sys-
tem warning display” on page 7-90.l One of the doors or the tailgate is not
completely closed.
The open door is displayed.l Close the door or tailgate.
Refer to “Door ajar warning display screen” on page 6-10.l The bonnet is open.lClose the bonnet.
Refer to “Bonnet” on page 11-04.l There is a fault in the electronic immobil-
izer (Anti-theft starting system).l Put the operation mode in OFF, and then
start the Plug-in Hybrid EV System again.If the warning is not cancelled, please
contact a MITSUBISHI MOTORS Au-
thorized Service Point.l The driver’s door is open when the opera-
tion mode is in any mode other than OFF.l Put the operation mode in OFF.
Refer to “Operation mode ON reminder
system” on page 7-14.l An attempt was made to lock all the doors
and the tailgate when the operation mode
is in any mode other than OFF.l Put the operation mode in OFF.
Refer to “Operation mode OFF reminder system” on page 7-14.
Indication lamp, warning lamp, and information screen display list
6-30OGGE17E1Instruments and controls6

ScreenCauseSolution (Reference)lThere is a fault in the electrical system.l Immediately stop the vehicle in a safe
place.
We recommend you to contact a MITSUBISHI MOTORS Authorized
Service Point.l The engine is overheated.lStop the vehicle in a safe place and take
corrective measures.
Refer to “Engine overheating” on page 9-09.l You put the operation mode in ON with-
out fastening your seat belt.l Fasten your seat belt properly. Refer to
“Seat belt reminder” on page 5-11.l There is a fault in the fuel system.l We recommend you to have it checked,
immediately.l The fuel is running low.lRefuel as soon as possible. Refer to
“Fuel
remaining warning display” on page 6-11.
Indication lamp, warning lamp, and information screen display list
6-31OGGE17E1Instruments and controls6

ScreenCauseSolution (Reference)lYou are driving with the parking brake
still applied.l Release the parking brake. Refer to
“Brake warning display” on page 6-52.l The brake fluid level in the reservoir has
fallen to a low level.
l There is a fault in the brake system.lImmediately stop the vehicle in a safe
place.
We recommend you to consult a MITSUBISHI MOTORS Authorized
Service Point.
Refer to “Brake warning display” on page 6-52.l When the brake pedal has been repeatedly
depressed over a short period of time, the brake warning lamp may come on and thebrake warning buzzer may sound, and this
warning may be displayed.l If this warning display has disappeared
and the brake warning lamp goes out and the buzzer stops a few seconds after stop-
ping the brake operation, there is no ab-
normality.l There is a fault with the Electric parking
brake.l We recommend you to have it checked,
immediately.
Refer to “Electric parking brake” on page
7-03.l The parking brake cannot be applied tem-
porarily due to repeated operation of the
Electric parking brake switch within a short time.l Refer to “Electric parking brake” on page
7-03.
Indication lamp, warning lamp, and information screen display list
6-32OGGE17E1Instruments and controls6

ScreenCauseSolution (Reference)lThe Ultrasonic misacceleration Mitigation
System sensor is temporarily not available for some reason such as the environmen-tal condition or increase of the sensor
temperature.l When the warning display does not disap-
pear after waiting for a while, contact a MITSUBISHI MOTORS Authorized
Service Point.
Refer to “Ultrasonic misacceleration Miti-
gation System” on page 7-74.l The Ultrasonic misacceleration Mitigation
System does not operate normally becausethere are some malfunctions in the sensor
or the system.l Immediately have your vehicle inspected
at a MITSUBISHI MOTORS Authorized
Service Point.
Refer to “Ultrasonic misacceleration Miti-
gation System” on page 7-74.
Indication lamp, warning lamp, and information screen display list
6-38OGGE17E1Instruments and controls6

ScreenCauseSolution (Reference)lThe Ultrasonic misacceleration Mitigation
System is activated.l Refer to “Ultrasonic misacceleration Miti-
gation System” on page 7-74.l The Blind Spot Warning (BSW) sensor is
temporarily not available for some reason such as the environmental condition or in-crease of the sensor temperature.l When the warning display does not disap-
pear after waiting for a while, contact a
MITSUBISHI MOTORS Authorized
Service Point.
Refer to “Blind Spot Warning (BSW)” on page 7-80.l The Blind Spot Warning (BSW) does not
operate normally because there are some malfunctions in the sensor or the system.l We recommend you to have it checked,
immediately.
Refer to “Blind Spot Warning (BSW)” on
page 7-80.
Indication lamp, warning lamp, and information screen display list
6-39OGGE17E1Instruments and controls6

ScreenCauseSolution (Reference)lForeign objects, such as dirt, snow or ice,
adhere to the bumper surface around the sensor.l Remove a foreign object on the bumper
surface around the sensor.
When the warning display does not disap- pear after having cleaned the bumper sur-face around the sensor, contact a MITSUBISHI MOTORS Authorized
Service Point.
Refer to “Blind Spot Warning (BSW):
When there is a foreign objects on the
sensor” on page 7-83.l The Rear Cross Traffic Alert (RCTA) has
detected a vehicle that is approaching
your vehicle.l Pay special attention to the rear of your
vehicle.
Refer to “Rear Cross Traffic Alert
(RCTA)” on page 7-83.l There is a fault in the sensor.l We recommend you to contact a
MITSUBISHI MOTORS Authorized
Service Point.
Refer to “Forward Collision Mitigation
System (FCM): When a problem is detec- ted” on page 7-70.
Refer to “Lane Departure Warning
(LDW): System problem warning” on page 7-87.
Refer to “Automatic high-beam system: System problem warning” on page 6-58.
Indication lamp, warning lamp, and information screen display list
6-40OGGE17E1Instruments and controls6

ScreenCauseSolution (Reference)lThe Forward Collision Mitigation System
(FCM), Lane Departure Warning (LDW)
and automatic high-beam system are tem-
porarily unavailable due to a high or low temperature of the sensor.l After the temperature of the sensor has
been in range, the system will automati-
cally return to operation.
Refer to “Forward Collision Mitigation System (FCM): When a problem is detec-
ted” on page 7-70.
Refer to “Lane Departure Warning
(LDW): System problem warning” on page 7-87.
Refer to “Automatic high-beam system: System problem warning” on page 6-58.l The sensor is temporarily unavailable due
to conditions such as the adhesion of con- taminants to the sensor or windscreen.This is not a malfunction.Refer to “Forward Collision Mitigation System
(FCM): When a problem is detected” on page
7-70.
Refer to “Lane Departure Warning (LDW):
System problem warning” on page 7-87.
Refer to “Automatic high-beam system: Sys- tem problem warning” on page 6-58.l There is a fault in the system of the auto-
matic high-beam.l We recommend you to contact a
MITSUBISHI MOTORS Authorized
Service Point.
Refer to “Automatic high-beam system: System problem warning” on page 6-58.

Navigation information dis-
play*
E00531401061
On vehicles equipped with MITSUBISHI
Multi-Communication System (MMCS), the
following information on navigation will be
displayed when guidance location such as junction and destination is approached after
Indication lamp, warning lamp, and information screen display list
6-41OGGE17E1Instruments and controls6

This informs you that a periodic inspection is due.ScreenSolutionWe recommend you to have it checked. Refer to “Service reminder” for further de-tails on page 6-12.
The setting for rest interval can be changed.
ScreenSolutionStop the vehicle in a safe place, stop the Plug-in Hybrid EV system, and take a rest.
Use this display as rough guide for taking rests during a long drive.
The interval from the start of your trip until this message is displayed can be set. Refer to “REST REMINDER” on page 6-21.
The display and buzzer alert the driver when the set time is reached. If you continue
to drive without having a rest, the buzzer sounds about every 5 minutes to encourage
you to take a rest.
l In the following cases, the time driven is reset and the display returns to the pre-
vious display screen. After this, when the set time is reached again, the buzzer
and display encourage you to take a rest. • The buzzer sounds 3 times.
• Put the operation mode in OFF.
• The multi information display switch is held for about 2 seconds or more.

Indication lamp, warning lamp, and information screen display list
6-48OGGE17E1Instruments and controls6