2017 MITSUBISHI OUTLANDER PHEV sensor

with the interior alarm sensor) will
sound intermittently.
3. The alarm will resume if unlawful ac-
tions are taken again, even if the alarm has stopped.
Cancelling the alarm
E00302001799
It is possible to halt the activation of an alarm
using the following methods:
l Pressing the LOCK or UNLOCK switch
on the remote control switch.
(After pressing the LOCK switch, the vehicle will lock if all the doors and the
tailgate are closed, after which the sys- tem preparation mode will once again go
into effect.)
l Putting the operation mode in ON.
l Holding the keyless operation key and
locking or unlocking the doors and the tailgate using the keyless operation func-
tion.NOTEl Even if a door or the tailgate is closed while
the inside alarm is activating, this will notcancel the alarm activation. (except for vehi-
cles equipped with the interior alarm sensor)
l When the operation mode is put in ON, the
buzzer sounds 4 times. This operation indi-
cates that the alarm was activated while the vehicle was parked.
Please check the inside of the vehicle to con-
firm that nothing was stolen.
l Even if the battery is disconnected, the alarm
activation memory will not be erased.Electric window control
E00302201632
The electric windows can only be operatedwith the operation mode in ON.
Electric window control switch
E00302301822
Each door window opens or closes while the
corresponding switch is operated.
1- Driver’s door window
2- Front passenger’s door window
3- Rear left door window
4- Rear right door window
5- Lock switch
WARNINGl Before operating the electric window con-
trol, make sure that nothing can get trap-
ped (head, hand, finger, etc.).
l Never leave the vehicle without removing
the key.
l Never leave a child (or other person who
might not be capable of safe operation of the electric window control) in the vehicle alone.
Electric window control
4-34OGGE17E1Locking and unlocking4 Driver’s switch RHDDriver’s switch LHD

If the vehicle is driven with the seat belt still
unfastened, the warning lamp will blink and
the tone will sound intermittently until the
seat belt is fastened. At the same time, “FAS-
TEN SEAT BELT” is displayed on the infor- mation screen in the multi information dis-
play for the driver.WARNINGl Do not install any accessory or sticker
that makes the lamp difficult to see.NOTEl If the seat belt subsequently remains unfas-
tened, the warning lamp and the tone will is-
sue further warnings each time the vehicle starts moving from a stop.
l For the front passenger seat, the warning
function works only while a person is sitting
on the seat.
l When luggage is placed on the front passen-
ger seat, a sensor in the seat cushion may,
depending on the weight and position of the
luggage, cause the warning tone to sound
and the warning lamp to come on.For the rear passenger’s seats
E00415501021
If the operation mode of the power switch is
put in ON while a seat belt is not fastened,
the warning lamp comes on for approximate-
ly 30 seconds to remind the rear passenger to fasten the seat belt.
If the vehicle is driven with the seat belt still
unfastened, the warning lamps come on for
approximately another 30 seconds. (This illu-
mination happens only the first time the vehi- cle starts moving with the seat belt still un-
fastened.)
The warning lamps go off when the seat belt is fastened.
WARNINGl Do not install any accessory or sticker
that makes the lamp difficult to see.NOTEl The warning lamp comes on even if no one
is sitting on the rear seats.
l If a seat belt is unfastened while the vehicle
is being driven, the tone sounds for approxi- mately 1 second and the warning lampcomes on for approximately 30 seconds. At the same time, the warning lamp for the seat
where the seat belt is not fastened comes on.
l If the seat belts are initially fastened but a
seat belt is unfastened while the vehicle is
stationary and the vehicle is then driven with the seat belt still unfastened, the warning
lamp comes on again for approximately 30 seconds.Adjustable seat belt anchor
(front seats)
E00405000420
The seat belt anchor height can be adjusted.
Seat belts
5-12OGGE17E1Seats and seat belts5

ScreenCauseSolution (Reference)lThe Adaptive Cruise Control System
(ACC) can not start the control because
the speed is out of speed range.l The Adaptive Cruise Control System
(ACC) can not start the control because
not detected the approach of the vehicles in front.l The Adaptive Cruise Control System
(ACC) is not available temporarily such
as for adhesion of contaminants to the sensor.
This is not a malfunction.l There is a fault in the Adaptive Cruise
Control System (ACC).l We recommend you to have it checked.
Refer to “Adaptive Cruise Control System
(ACC)” on page 7-52.l There is a fault in the Forward Collision
Mitigation System (FCM).l We recommend you to have it checked.
Refer to “Forward Collision Mitigation System (FCM)” on page 7-64.
Indication lamp, warning lamp, and information screen display list
6-36OGGE17E1Instruments and controls6

ScreenCauseSolution (Reference)lThe Ultrasonic misacceleration Mitigation
System sensor is temporarily not available for some reason such as the environmen-tal condition or increase of the sensor
temperature.l When the warning display does not disap-
pear after waiting for a while, contact a MITSUBISHI MOTORS Authorized
Service Point.
Refer to “Ultrasonic misacceleration Miti-
gation System” on page 7-74.l The Ultrasonic misacceleration Mitigation
System does not operate normally becausethere are some malfunctions in the sensor
or the system.l Immediately have your vehicle inspected
at a MITSUBISHI MOTORS Authorized
Service Point.
Refer to “Ultrasonic misacceleration Miti-
gation System” on page 7-74.
Indication lamp, warning lamp, and information screen display list
6-38OGGE17E1Instruments and controls6

ScreenCauseSolution (Reference)lThe Ultrasonic misacceleration Mitigation
System is activated.l Refer to “Ultrasonic misacceleration Miti-
gation System” on page 7-74.l The Blind Spot Warning (BSW) sensor is
temporarily not available for some reason such as the environmental condition or in-crease of the sensor temperature.l When the warning display does not disap-
pear after waiting for a while, contact a
MITSUBISHI MOTORS Authorized
Service Point.
Refer to “Blind Spot Warning (BSW)” on page 7-80.l The Blind Spot Warning (BSW) does not
operate normally because there are some malfunctions in the sensor or the system.l We recommend you to have it checked,
immediately.
Refer to “Blind Spot Warning (BSW)” on
page 7-80.
Indication lamp, warning lamp, and information screen display list
6-39OGGE17E1Instruments and controls6

ScreenCauseSolution (Reference)lForeign objects, such as dirt, snow or ice,
adhere to the bumper surface around the sensor.l Remove a foreign object on the bumper
surface around the sensor.
When the warning display does not disap- pear after having cleaned the bumper sur-face around the sensor, contact a MITSUBISHI MOTORS Authorized
Service Point.
Refer to “Blind Spot Warning (BSW):
When there is a foreign objects on the
sensor” on page 7-83.l The Rear Cross Traffic Alert (RCTA) has
detected a vehicle that is approaching
your vehicle.l Pay special attention to the rear of your
vehicle.
Refer to “Rear Cross Traffic Alert
(RCTA)” on page 7-83.l There is a fault in the sensor.l We recommend you to contact a
MITSUBISHI MOTORS Authorized
Service Point.
Refer to “Forward Collision Mitigation
System (FCM): When a problem is detec- ted” on page 7-70.
Refer to “Lane Departure Warning
(LDW): System problem warning” on page 7-87.
Refer to “Automatic high-beam system: System problem warning” on page 6-58.
Indication lamp, warning lamp, and information screen display list
6-40OGGE17E1Instruments and controls6

ScreenCauseSolution (Reference)lThe Forward Collision Mitigation System
(FCM), Lane Departure Warning (LDW)
and automatic high-beam system are tem-
porarily unavailable due to a high or low temperature of the sensor.l After the temperature of the sensor has
been in range, the system will automati-
cally return to operation.
Refer to “Forward Collision Mitigation System (FCM): When a problem is detec-
ted” on page 7-70.
Refer to “Lane Departure Warning
(LDW): System problem warning” on page 7-87.
Refer to “Automatic high-beam system: System problem warning” on page 6-58.l The sensor is temporarily unavailable due
to conditions such as the adhesion of con- taminants to the sensor or windscreen.This is not a malfunction.Refer to “Forward Collision Mitigation System
(FCM): When a problem is detected” on page
7-70.
Refer to “Lane Departure Warning (LDW):
System problem warning” on page 7-87.
Refer to “Automatic high-beam system: Sys- tem problem warning” on page 6-58.l There is a fault in the system of the auto-
matic high-beam.l We recommend you to contact a
MITSUBISHI MOTORS Authorized
Service Point.
Refer to “Automatic high-beam system: System problem warning” on page 6-58.

Navigation information dis-
play*
E00531401061
On vehicles equipped with MITSUBISHI
Multi-Communication System (MMCS), the
following information on navigation will be
displayed when guidance location such as junction and destination is approached after
Indication lamp, warning lamp, and information screen display list
6-41OGGE17E1Instruments and controls6

ScreenSystem operation statusReferencelWhen approaching the guidance location,
etc.l Refer to “Navigation information display”
on page 6-41.l When the EV priority mode is activated.l Refer to “EV switch” on page 7-25.lWhen the battery save mode is activated.l Refer to “Battery save mode switch” on
page 7-27.l When the battery charge mode is activa-
ted.l Refer to “Battery charge mode switch” on
page 7-28.l When the reversing sensor system detects
an obstruction.l Refer to “Reversing sensor system” on
page 7-94.
Indication lamp, warning lamp, and information screen display list
6-46OGGE17E1Instruments and controls6