If your vehicle meets the access conditions
for carpool lanes, you can use this function.
Navigation includes carpool lanes if the car-
pool lanes option is activated.
Depending on local conditions, the multimedia
system may not always be able to include all
route options. A route may include a ferry, for
instance, even though Avoid Ferries
is ena-
bled. The multimedia system will notify you of
this visually as well as through a navigation mes-
sage.
XTo use toll roads: turn and press the con-
troller.
A menu appears.
XSelect an option.
The options include using roads that require
cash payment or electronic billing, or switch-
ing off the function.
XTo exit a menu: slide1 the controller.
Selecting announcements
XTo switch to navigation mode: press the
Ø button.
XTo show the menu: slide6the controller.
XTo select Options: turn and press the con-
troller.
XSelect Settings.
A menu appears.
XSelect an option.
Switch the option on Oor off ª.
AnnounceStreetNames
The multimedia system
announces the name of the
road onto which the upcoming
change of direction leads.
The function is not available in
all countries.
AudioFadeoutThe volume of an active media
source is automatically
reduced during a navigation
announcement.
Gas onReserveFunction activated: once the
reserve fuel tank level is
reached, a message appears in
the multimedia system to help
you start the search for a gas
station.
Atten‐tionAssist
Function activated: if ATTEN-
TION ASSIST displays a warn-
ing in the multifunction display,
a message appears in the mul-
timedia system to help you
start the search for a rest stop.
If a route contains highways, a
rest stop search is started in
the vicinity. The map is shown
with the message: Searching
For a Rest Area in theVicinity…. If service stations
are found, the nearest service
station is highlighted on the
map.
Further information about
ATTENTION ASSIST can be
found in the vehicle Operator's
Manual.
Using car pool lanes
You can include carpool lanes (HOV or car shar-
ing lanes) in the route calculation.
If you use HOV or carpool lanes, please observe
the applicable laws as well as the local and time
limitation conditions.
Carpool lanes may only be used under certain
conditions. They can normally be used when
there are two people in the vehicle. However,
70Basic settings
Navigation
there are also carpool lanes which can only be
used when there are three or more people in the
vehicle. In California, lone drivers can use a car-
pool lane if their vehicle's emission level or fuel
consumption is below a fixed threshold.
Carpool lanes may be reserved for specific
times (e.g. during the peak period).
Carpool lanes are indicated by a diamond sym-
bol on specific road signs and on the road sur-
face. The road signs may also include the des-
ignation CARPOOL. The lanes are arranged as a
separate lane next to the others or are built as a
physically separate lane.
Depending on the setting underUse Carpool
Lanes, the multimedia system uses carpool lanes when calculating the route. The multime-
dia system then guides you in and out of carpool
lanes using visual and acoustic driving direc-
tions.
XTo switch to navigation mode:
press the
ß button.
XTo show the menu: slide6the controller.
XTo select Options: turn and press the con-
troller.
XSelect Route Settings.
XSelectAvoid Options.
XSelectUse Carpool Lanes.
Carpool lanes will either be used Oor avoi-
ded ªwhen calculating the route.
Destination entry
Important safety notes
GWARNING
If you operate information systems and communication equipment integrated in the vehicle while driving, you will be distracted from traffic conditions. You could also lose control of the vehicle.
There is a risk of an accident.
Only operate the equipment when the traffic situation permits. If you are not sure that this is
possible, park the vehicle paying attention to traffic conditions and operate the equipment when
the vehicle is stationary.
You must observe the legal requirements for the country in which you are currently driving when
operating the multimedia system.
Destination entry may be blocked while driving, depending on the country specifications.
General notes
The various character entry options are described for the controller. Alternatively you can use the
touchpad to enter characters and select menus (Ypage 28).
Destination entry71
Navigation
Z
XAs a contact:selectAs New Contact.
XSelect Not Classified,Homeor Work.
XEnter a surname and a first name (Ypage 34).
XTo select ¬: turn and press the controller.
The destination address is saved in the
address book as a navigable contact.
Starting route calculation
The entered destination appears in the address entry menu.
XTo confirm StartorContinue: press the controller.
If you select Start: the routeis calculated with the current route settings (Ypage 69). While route
calculation is in progress, an arrow will indicate the direction to your destination. Once the route
has been calculated, route guidance begins. Ifthe vehicle is traveling on a non-digitized road, the
system displays the linear distance to the destination, the direction to the destination and the
Road Not Mapped
message.
Selection Continue
:If Calculate Alternative Routesis activated, alternative routes are
calculated (Ypage 69). You can display these and select them for route guidance (Ypage 93).
If route guidance has already been activated, a prompt will appear asking whether you wish to end
the current route guidance.
XTo select CancelActiveRouteGuidanceorSetasIntermediateDestination: turn and
press the controller.
Cancel
ActiveRouteGuidancecancels the current route guidance and starts route calcula-
tion to the new destination.
Set
asIntermediateDestinationadds the newly entered intermediate destination in addi-
tion to the existing destination. The intermediate destinations menu appears (Ypage 80).
iThe route is calculated using digital map data. The calculation time depends on the distance
from the destination, for example.
The calculated route may differ from the ideal route, e.g. due to roadworks or incomplete map
data. Please also refer to the notes about the digital map (
Ypage 108).
XTo call up key word search: selectèby sliding 6, turning and pressing the controller in the
address entry menu.
74Destination entry
Navigation
For further information on the keyword search (Ypage 75).
XTo view the vicinity of the destination:to select:, turn and press the controller.
You can explore the destination area.
Requirement for exploring a destination (USA): mbrace must be activated for Internet access
(
Ypage 142).
Requirement for exploring a destination (Canada): a mobile phone is connected to the multimedia
system via Bluetooth
®(Ypage 113) or USB (Ypage 183).
Keyword search
Entering keywords
The keyword search is used to help find desti-
nations using fragments of words. The keyword
search is tolerant of errors.
It can be used for an address or a POI. For exam-
ple, you can search for the Empire State Building
in New York in this way.
The keyword search finds geographically toler-
ant hits. If, for example, you are searching for a
street located on the edge of a major city, the
search will also cover adjacent smaller cities.
The keyword search supports languages using
Latin characters.
XTo switch to navigation mode: press the
Ø button.
XTo show the menu: slide6the controller.
XTo select Destination: turn and press the
controller.
XSelect Keyword Search.
XEnter the first few letters of the city and street
or the POI, e.g. EMPandSTATE.
While entering the information, the number of
exact matches/all hits is shown.
---/---
is displayed if fewer than three char-
acters have been entered. 999+
is displayed if there are too many hits.
XSelect
¬.
The search results are displayed
(
Ypage 75).
Selecting search results
The search results are divided into categories,
such as addresses. The number of exact/total
hits is shown in brackets.
Further search results are displayed, if POI
Searchand/orFuzzy Searchare activated in
the search options (Ypage 76).
XTo select an address: press the controller.
The search results are displayed.
Destination entry75
Navigation
Z
Exact hits are shown at the very top of the list.
Hits are listed alphabetically. The search term
is highlighted in orange for exact matches.
XSelect an entry: turn and press the controller.
The address entry menu appears, showing the
destination address.
XTo start route calculation: select Start(Ypage 74).
XTo select a POI:selectPOIsintheVicin‐
ityorAll POIsby turning and pressing the
controller.
A list appears.
XSelect a POI.
The POI is shown.
XTo start route calculation: select Start(Ypage 74).
XTo use online search:selectOnline
Search.
The search switches to the online functions.
Online search requirement (USA): mbrace
must be activated for Internet access
(
Ypage 142).
Requirement for the online map display (Can-
ada): a mobile phone is connected to the mul-
timedia system via Bluetooth
®(Ypage 113)
or USB (Ypage 183).
Selecting search options
XTo switch to navigation mode: press the
Ø button.
XTo show the menu: slide6the controller.
XTo select Destination: turn and press the
controller.
XSelect Keyword Search.
XTo select Search Options: slide5, turn
and press the controller.
XSelect Fuzzy SearchorPOI Search.
Switch the setting on Oor off ª.
The error-tolerant search is useful if parts of
the address are incomplete or the spelling is
unclear.
The POI search takes into account points of
interest in the search.
Selecting a state/province
XTo switch to navigation mode: press the
Ø button.
XTo show the menu: slide6the controller.
XTo select Destination: turn and press the
controller.
XSelect Keyword Search.
XTo select State/Province: slide5, turn
and press the controller.
States/provinces are sorted alphabetically.
XTo select a state/province: turn and press the
controller.
Using online search
Requirement (USA): mbrace must be activated
for Internet access (Ypage 142).
Requirement (Canada): a mobile phone is con-
nected to the multimedia system via Bluetooth
®
(Ypage 113) or USB (Ypage 183).
XTo switch to navigation mode: press the
Ø button.
XTo show the menu: slide6the controller.
XTo select Destination: turn and press the
controller.
XSelect Keyword Search.
XTo select OnlineSearch: slide5, turn and
press the controller.
The search switches to the online functions.
Selecting a destination from the list of
last destinations
The last 50 destinations are stored automati-
cally.
XTo switch to navigation mode: press the
Ø button.
XTo show the menu: slide6the controller.
XTo select Destination: turn and press the
controller.
XSelect From Previous Destinations.
76Destination entry
Navigation
The search results display the following information:
Ran arrow that shows the linear direction to the POI (search around vehicle position)
Rthe linear distance to the POI
Rthe name of the POI
XSelect a POI.
The complete address of the POI is shown.
SelectionInstructions
Search By Name
The search looks for all
POIs on the digital map or
around one of the three
previously specified posi-
tions (
Ypage 78).
XTo selectSearch By Name: turn and press the controller.
XSelectAll POIsor a position for the POI search.
The search for POIs starts.
Search By Phone Num‐ber
All POIs with a telephone
number can be selected.
XTo select Search By Phone Number: turn and press the control-
ler.
The search for POIs starts.
Mercedes-Benz Ser‐vice
The search looks for
authorized Mercedes-
Benz Centers.
XTo select Mercedes-BenzService: turn and press the controller.
The search for POIs starts.
Defining the position for the POI search
You can define where the POI search is to be carried out during active route guidance by selecting
Near Destinationor Along the Route.
The POI search covers a 240 mi (400 km) radius around the selected position.
SelectionInstructions
Near Destination
The search is performed
in the vicinity of the desti-
nation.
XSelect a category or Search By Name(Ypage 77).
XSelectNear Destination.
The search for POIs starts.
Along the Route
The search is performed
along the route.
XSelect a category or Search By Name(Ypage 77).
XSelectAlong the Route.
The search for POIs starts.
Current Position
Searches in the vicinity of
the current vehicle posi-
tion.
XSelect a category or Search By Name(Ypage 77).
XSelectCurrent Position.
The search for POIs starts.
Selecting a POI
Requirement for "Calling up a POI": a mobile phone must be connected to the multimedia system
(Ypage 113).
78Destination entry
Navigation
Requirement for "Viewing thevicinity of the destination" and "Calling up the website for the desti-
nation" (USA): mbrace must be activated for Internet access (Ypage 142).
Requirement for "Viewing the vicinity of the destination" and "Calling up the website for the desti-
nation" (Canada): a mobile phone must be connected via Bluetooth
®(Ypage 113) or USB
(Ypage 183) with the multimedia system.
XTo view the vicinity of the destination: to select:, turnand press th econtroller.
If stree t images are available, the street in the vicinity of the destination address is shown.
XTo call up th emap: select Map.
XMovethe map, change the map scale and select the POI (Ypage 80).
XTo call up a POI:selectCall.
If a phone number is available, the multimedia system switches to the telephone function.
XTo call up th e websitefor the destination: selectwww.
If an Internet address is available, data is loaded from theInternet .
XTo saveaPOI: selectSaveby turning thecontroller and pressing to confirm.
The POI can be saved as:
Ra navigable address book contact
Ra home address
XTo start route calculation: press thecontroller to select Start(Ypage 74).
Destination entry79
Navigation
Z
Using the map
:Crosshair
;Distance of crosshair position from current vehicle position
XTo switch to navigation mode:press theßbutton.
XTo show the menu: slide6the controller.
XTo select Destination: turn and press the controller.
XSelectUsing Map.
The map with crosshair is shown.
XTo move the map: slide1, 4or2 the controller.
XTo change the map scale: turn the controller until the desired map scale is selected.
The scale is displayed at the bottom. Turning clockwise zooms out from the map; turning counter-
clockwise zooms in.
XTo select a destination: press the controller.
If several destinations are available in the area around the crosshair, these are also displayed.
XTo select a destination from the selection list: turn and press the controller.
If the digital map provides navigable address data, you will see the destination address in the
address entry menu.
XTo start route calculation: selectStart(Ypage 74).
Entering intermediate destinations
Introduction
You can also map the route to the destination
yourself by entering up to four intermediate des-
tinations. The sequence of the intermediate des-
tinations can be changed at any time.
The navigation system provides a selection of
predefined destinations in eight categories for
this purpose, e.g. Gas Station
orRestau‐rants. You can also use the destination entry
options to enter intermediate destinations.
Creating intermediate destinations
XTo switch to navigation mode: press the
Ø button.
XTo show the menu: slide6the controller.
XTo select Destination: turn and press the
controller.
XSelect Intermediate Destinations.
XTo select a category or Other: turn and press
the controller.
After selecting a category, the POIs which are
available along the route and in the vicinity are displayed.
First, a search for destinations along the route
is performed. The search for destinations is
80Destination entry
Navigation