2017 MAZDA MX5 MIATA light

6 –43 Maintenance and Care
Owner Maintenance
*Some models. Replacing a Tire
WARNING Always use tires that are in good
condition:
Driving with worn tires is dangerous.
Reduced braking, steering, and
traction could result in an accident.
Replace all four tires at the same time:
Replacing just one tire is dangerous. It
could cause poor handling and poor
braking resulting in loss of vehicle
control. Mazda strongly recommends
that you replace all four tires at the
same time.
If a tire wears evenly, a wear indicator will
appear as a solid band across the tread.
Replace the tire when this happens.
Ne w tread Tread wear indicator
Worn tread
You should replace the tire before the band
crosses the entire tread.
(With tire pressure monitoring system)
After adjusting the tire pressure,
initialization of the tire pressure
monitoring system is necessary to make
the system operate normally.
Refer to Tire Pressure Monitoring System
Initialization on page 4-108 . NOTE
Tires degrade over time, even when
they are not being used on the road. It
is recommended that tires generally be
replaced when they are 6 years or older.
Heat caused by hot climates or frequent
high loading conditions can accelerate the
aging process. The period in which the tire
was manufactured (both week and year) is
indicated by a 4-digit number.
Refer to Tire Labeling on page 8-24 .
Replacing a Wheel
WARNING Always use wheels of the correct size on
your vehicle:
Using a wrong-sized wheel is
dangerous. Braking and handling
could be affected, leading to loss of
control and an accident.
CAUTION A wrong-sized wheel may adversely
affect: 
Tire fit 
Wheel and bearing life 
Ground clearance 
Snow-chain clearance 
Speedometer calibration 
Headlight aim 
Bumper height 
Tire Pressure Monitoring System *
MX-5_8FR4-EA-16J_Edition1.indb 43 2016/08/11 20:29:47

6 –45 Maintenance and Care
Owner Maintenance
Light Bulbs Overhead light
Side turn signal lights
High-mount brake lightTrunk lightFront side-marker lights
Front turn signal lights
Headlights (low beam)P arking lights
Headlights (High beam)
Daytime running lights
License plate lights
Brake lights
TaillightsRear side-marker lights
Reverse lights
Rear turn signal lights
MX-5_8FR4-EA-16J_Edition1.indb 45 2016/08/11 20:29:47

6 –46 Maintenance and Care
Owner Maintenance
CAUTION When removing the lens or lamp unit
using a flathead screwdriver, make
sure that the flathead screwdriver does
not contact the interior terminal. If
the flathead screwdriver contacts the
terminal, a short circuit may occur.
NOTE 
To replace the bulb, contact an
Authorized Mazda Dealer. 
Use the protective cover and carton for
the replacement bulb to dispose of the
old bulb promptly and out of the reach
of children.
Replacing Exterior Light BulbsHeadlights, Daytime running lights
(LED type), Parking lights, High-mount
brake light, Brake lights, Taillights
The LED bulb cannot be replaced as a
single unit because it is an integrated unit.
The LED bulb has to be replaced with the
unit. We recommend an Authorized Mazda
Dealer when the replacement is necessary. Daytime running lights (Bulb type)
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Pull the center of each plastic retainer
and remove the retainers.
Rem ova l
Installation
3. Turn the screw counterclockwise and
remove it, and then partially peel back
the mudguard.

4. Turn the socket and bulb assembly
counterclockwise and remove it.
MX-5_8FR4-EA-16J_Edition1.indb 46 2016/08/11 20:29:48

6 –47 Maintenance and Care
Owner Maintenance5. Disconnect the bulb from the socket.

6. Install the new bulb in the reverse order
of the removal procedure.
Front side-marker lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. If you are changing the right bulb, start
the engine, turn the steering wheel
all the way to the right, and turn off
engine. If you are changing the left
bulb, turn the steering wheel to the left.
3. Pull the center of each plastic retainer
and remove the retainers, and then
partially peel back the mudguard.
Rem ova l
Installation
4. Turn the socket and bulb assembly
counterclockwise and remove it. 5. Disconnect the bulb from the socket.

6. Install the new bulb in the reverse order
of the removal procedure.
Front turn signal lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. If you are changing the right bulb, start
the engine, turn the steering wheel
all the way to the right, and turn off
engine. If you are changing the left
bulb, turn the steering wheel to the left.
3. Pull the center of each plastic retainer
and remove the retainers, and then
partially peel back the mudguard.
Rem ova l
Installation
MX-5_8FR4-EA-16J_Edition1.indb 47 2016/08/11 20:29:48

6 –48 Maintenance and Care
Owner Maintenance 4. Disconnect the connector from the unit
by pressing the tab on the connector
with your finger and pulling the
connector rearward.

5. Turn the socket and bulb assembly
counterclockwise and remove it.
6. Disconnect the bulb from the socket.

7. Install the new bulb in the reverse order
of the removal procedure.
Side turn signal lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. If you are changing the right bulb, start
the engine, turn the steering wheel
all the way to the right, and turn off
engine. If you are changing the left
bulb, turn the steering wheel to the left. 3. Pull the center of each plastic retainer
and remove the retainers, and then
partially peel back the mudguard.
Rem ova l
Installation
4. Remove the unit by pressing the tab on
the unit with your finger and pulling the
unit forward.

5. Detach the electrical connector from
the unit by pulling it to the rear.

6. Install the new side turn signal unit
in the reverse order of the removal
procedure.
MX-5_8FR4-EA-16J_Edition1.indb 48 2016/08/11 20:29:48

6 –49 Maintenance and Care
Owner MaintenanceRear turn signal lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Pull the center of each plastic retainer
and remove the retainers and the trunk
end trim.

Rem ova l
Installation
3. Disconnect the connector from the unit
by pressing the tab on the connector
with your finger and pulling the
connector downward.
4. Pull the center of each plastic retainer
and remove the retainers, and then
partially peel back the trunk side trim.
Rem ova l
Installation
MX-5_8FR4-EA-16J_Edition1.indb 49 2016/08/11 20:29:48

6 –52 Maintenance and Care
Owner Maintenance Rear side-marker lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Turn the socket and bulb assembly
counterclockwise and remove it.
3. Disconnect the bulb from the socket.

4. Install the new bulb in the reverse order
of the removal procedure. Reverse lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Turn the socket and bulb assembly
counterclockwise and remove it.
3. Disconnect the bulb from the socket.

4. Install the new bulb in the reverse order
of the removal procedure.
License plate lights
1. Make sure the ignition is switched off,
and the headlight switch is off.
2. Remove the unit by pressing the tab on
the unit with your finger and pulling the
unit downward.

3. Turn the socket and bulb assembly
counterclockwise and remove it.
MX-5_8FR4-EA-16J_Edition1.indb 52 2016/08/11 20:29:49

6 –53 Maintenance and Care
Owner Maintenance4. Disconnect the bulb from the socket.

5. Install the new bulb in the reverse order
of the removal procedure.
Replacing Interior Light BulbsOverhead light
1. Wrap a small flathead screwdriver
with a soft cloth to prevent damage to
the lens, and then remove the lens by
carefully prying on the edge of the lens
with the flathead screwdriver.
2. Disconnect the bulb by pulling it out.

3. Install the new bulb in the reverse order
of the removal procedure. Trunk light
1. Wrap a small flathead screwdriver
with a soft cloth to prevent damage to
the lens, and then remove the lens by
carefully prying on the edge of the lens
with the flathead screwdriver.

2. Disconnect the connector from the unit.
3. Disconnect the bulb by pulling it out.

4. Install the new bulb in the reverse order
of the removal procedure.
MX-5_8FR4-EA-16J_Edition1.indb 53 2016/08/11 20:29:49