2017 MAZDA MODEL MX-5 lock

4–87
When Driving
i-ACTIVSENSE
 


y In the following cases, the activation of the Blind Spot Monitoring (BSM) warning lights
and the warning beep may not occur or they may be delayed.
 


y A vehicle makes a lane change from a driving lane two lanes over to an adjacent lane.



y Driving on steep slopes.



y Crossing the summit of a hill or mountain pass.



y The turning radius is small (making a sharp turn, turning at intersections).



y When there is a difference in the height between your driving lane and the adjacent
lane.
 


y Directly after pressing the Blind Spot Monitoring (BSM) switch and the system
becomes operable.
 


y If the road width is extremely narrow, vehicles two lanes over may be detected.
The detection area of the radar sensors (rear) is set according to the road width of
expressways.
 


y The Blind Spot Monitoring (BSM) warning lights may turn on in reaction to stationary
objects on the road or the roadside such as guardrails, tunnels, sidewalls, and parked
vehicles.

Objects such as guardrails and concrete walls
running alongside the vehicle.Places where the width between guardrails or
walls on each side of the vehicle narrows.

The walls at the entrance and exits of tunnels,
turnouts.
 

y A Blind Spot Monitoring (BSM) warning light may À ash or the warning beep may be
activated several times when making a turn at a city intersection.
 


y Turn off the Blind Spot Monitoring (BSM) while pulling a trailer or while an accessory
such as a bicycle carrier is installed to the rear of the vehicle. Otherwise, the radar’s
radio waves will be blocked causing the system to not operate normally.
/:A(4'#,A'FKVKQPKPFD/:A(4'#,A'FKVKQPKPFD

4–94
When Driving
i-ACTIVSENSE
 


y Under the following conditions, the radar sensors (rear) cannot detect target objects or it
may be dif¿ cult to detect them.

y The vehicle speed when reversing is about 10 km/h (6.3 mph) or faster. 



y The radar sensor (rear) detection area is obstructed by a nearby wall or parked
vehicle. (Reverse the vehicle to a position where the radar sensor detection area is no
longer obstructed.)

Your vehicle
 


y A vehicle is approaching directly from the rear of your vehicle.

Your vehicle
 


y The vehicle is parked on a slant.

Your vehicle
 


y Directly after pressing the Blind Spot Monitoring (BSM) switch and the system
becomes operable.
 


y In the following cases, it may be dif¿ cult to view the illumination/À ashing of the Blind
Spot Monitoring (BSM) warning lights equipped on the door mirrors.
 


y Snow or ice adheres to the door mirrors.



y The door glass is fogged or covered in snow, frost or dirt. 



y Turn off the Rear Cross Traf¿ c Alert (RCTA) system while pulling a trailer or while an
accessory such as a bicycle carrier is installed to the rear of the vehicle. Otherwise,
the radio waves emitted by the radar will be blocked causing the system to not operate
normally.

/:A(4'#,A'FKVKQPKPFD/:A(4'#,A'FKVKQPKPFD

4–99
When Driving
i-ACTIVSENSE
N O T E
 


y The detection ability of the radar sensors (rear) has limitations. In the following cases,
the detection ability may lower and the system may not operate normally.
 


y The rear bumper near the radar sensors (rear) has become deformed.



y Snow, ice or mud adheres to the radar sensors (rear) on the rear bumper.



y Under bad weather conditions such as rain, snow and fog. 



y Under the following conditions, the radar sensors (rear) cannot detect target objects or it
may be dif¿ cult to detect them.




y Stationary objects on a road or a road side such as small, two-wheeled vehicles,
bicycles, pedestrians, animals, and shopping carts.
 


y Vehicle shapes which do not reÀ ect radar waves well such as empty trailers with a low
vehicle height and sports cars.
 


y Vehicles are shipped with the direction of the radar sensors (rear) adjusted for each
vehicle to a loaded vehicle condition so that the radar sensors (rear) detect approaching
vehicles correctly. If the direction of the radar sensors (rear) has deviated for some
reason, have the vehicle inspected at an Authorized Mazda Dealer.
 


y For repairs or replacement of the radar sensors (rear), or bumper repairs, paintwork,
and replacement near the radar sensors, consult an Authorized Mazda Dealer.
 


y Turn off the system while pulling a trailer or while an accessory such as a bicycle carrier
is installed to the rear of the vehicle. Otherwise, the radio waves emitted by the radar will
be blocked causing the system to not operate normally.
 


y The radar sensors are regulated by the relevant radio wave laws of the country in which
the vehicle is driven. If the vehicle is driven abroad, authorization from the country in
which the vehicle is driven may be required.

/:A(4'#,A'FKVKQPKPFD/:A(4'#,A'FKVKQPKPFD

5–1
5Interior Features
Use of various features for ride comfort, including air-conditioning and
audio system.

Climate Control System..................................................................... 5-2
Operating Tips ............................................................................... 5-2
Vent Operation .............................................................................. 5-3
Manual Type ................................................................................. 5-5
Fully Automatic Type .................................................................... 5-9

Audio System .................................................................................... 5-13
Antenna ....................................................................................... 5-13
Operating Tips for Audio System ............................................... 5-14
Audio set [Type A (non-touchscreen)] ........................................ 5-22
Audio set [Type B (touchscreen)] ............................................... 5-34
Audio Control Switch Operation ................................................ 5-55
AUX/USB mode ......................................................................... 5-57

Bluetooth
® ......................................................................................... 5-74
Bluetooth® ................................................................................... 5-74
Bluetooth® Hands-Free (Type A) ................................................ 5-97
Bluetooth® Hands-Free (Type B) .............................................. 5-103
Bluetooth® Audio (Type A) ....................................................... 5-113
Bluetooth® Audio (Type B) ....................................................... 5-115
Troubleshooting ........................................................................ 5-129

Interior Equipment ........................................................................ 5-132
Sunvisors ................................................................................... 5-132
Interior Lights ........................................................................... 5-132
Accessory Sockets .................................................................... 5-134
Cup Holder ................................................................................ 5-135
Storage Compartments .............................................................. 5-138
Windblocker .............................................................................. 5-140
/:A(4'#,A'FKVKQPKPFD/:A(4'#,A'FKVKQPKPFD

5–6
Interior Features
Climate Control System
Control Switches
Temperature control dial
This dial controls temperature. Turn it
clockwise for hot and counterclockwise
for cold.
N O T E
(Type A)
When the mode is set to
, or a position
in between them with the fan control dial
in a position other than 0 and the
temperature control dial in the maximum
cold position, the air intake selector
switches to the recirculated air position
and the A/C turns on automatically.
If A/C is not desired, press the A/C switch
to turn it off.

Fan control dial
This dial allows variable fan speeds.
The fan has seven speeds.
Mode selector dial
Turn the mode selector dial to select
airÀ ow mode (page 5-4 ).
N O T E




y The mode selector dial can be set at the
intermediate positions (
) between
each mode. Set the dial to an
intermediate position if you want to split
the airÀ ow between the two modes.




y For example, when the mode selector
dial is at the
position between the
and
positions, airÀ ow from the À oor
vent is less than that of the
position.
A/C switch
Press the A/C switch to turn the air
conditioner on. The indicator light on the
switch will illuminate when the fan control
dial is in any position except OFF.

Press the switch once again to turn the air
conditioner off.
N O T E
The air conditioner may not function when
the outside temperature approaches 0 °C
(32 °F).

Air intake selector
This switch controls the source of air
entering the vehicle.

Outside or recirculated air positions can be
selected. Press the switch to select outside/
recirculated air positions.
Recirculated air position (indicator light
illuminated)
Outside air is shut off. Use this position
when going through tunnels, driving in
congested traf¿ c (high engine exhaust
areas) or when quick cooling is desired.
Outside air position (indicator light
turned off)
Outside air is allowed to enter the
cabin. Use this mode for ventilation or
windshield defrosting.
WARNING
Do not use the position in cold or
rainy weather:
Using the
position in cold or rainy
weather is dangerous as it will cause
the windows to fog up. Your vision will
be hampered, which could lead to a
serious accident.

/:A(4'#,A'FKVKQPKPFD/:A(4'#,A'FKVKQPKPFD

5–7
Interior Features
Climate Control System
Rear window defogger switch
Press the rear window defogger switch to
defrost the rear window.
Refer to Rear Window Defogger on page
4-55 .
Heating
1. Set the mode selector dial to the
position.
2. Set the air intake selector to the outside
air position (indicator light turns off).
3. Set the temperature control dial to the
hot position.
4. Set the fan control dial to the desired
speed.
5. If dehumidi¿ ed heating is desired, turn
on the air conditioner.

N O T E
 


y If the windshield fogs up easily, set the
mode selector dial to the
position. 


y If cooler air is desired at face level, set
the mode selector dial at the
position
and adjust the temperature control dial
to maintain maximum comfort.
 


y The air to the À oor is warmer than air
to the face (except when the temperature
control dial is set at the extreme hot or
cold position).

Cooling (With air conditioner)
1. Set the mode selector dial to the
position.
2. Set the temperature control dial to the
cold position.
3. Set the fan control dial to the desired
speed.
4. Turn on the air conditioner by pressing
the A/C switch.
5. After cooling begins, adjust the fan
control dial and temperature control
dial as needed to maintain maximum
comfort.

CAUTION
If the air conditioner is used while
driving up long hills or in heavy
traffi c, monitor the engine coolant
temperature warning light to see if it is
illuminated or fl ashing (page 4-18 ).
The air conditioner may cause engine
overheating. If the warning light is
illuminated or fl ashing, turn the air-
conditioning off (page 7-27 ).

N O T E




y When maximum cooling is desired,
set the temperature control dial to the
extreme cold position and set the air
intake selector to the recirculated air
position, then turn the fan control dial
fully clockwise.
 


y If warmer air is desired at À oor level,
set the mode selector dial at the

position and adjust the temperature
control dial to maintain maximum
comfort.
 


y The air to the À oor is warmer than air
to the face (except when the temperature
control dial is set at the extreme hot or
cold position).

Ventilation
1. Set the mode selector dial to the
position.
2. Set the air intake selector to the outside
air position (indicator light turns off).
3. Set the temperature control dial to the
desired position.
4. Set the fan control dial to the desired
speed.

/:A(4'#,A'FKVKQPKPFD/:A(4'#,A'FKVKQPKPFD

5–8
Interior Features
Climate Control System
Windshield Defrosting and
Defogging
1. Set the mode selector dial to the
position.
2. Set the temperature control dial to the
desired position.
3. Set the fan control dial to the desired
speed.
4. If dehumidi¿ ed heating is desired, turn
on the air conditioner.

WARNING
Do not defog the windshield using the

position with the temperature
control set to the cold position:
Using the
position with the
temperature control set to the cold
position is dangerous as it will cause
the outside of the windshield to fog up.
Your vision will be hampered, which
could lead to a serious accident. Set
the temperature control to the hot or
warm position when using the

position.

N O T E
 


y For maximum defrosting, turn on the air
conditioner, set the temperature control
dial to the extreme hot position, and
turn the fan control dial fully clockwise.
 


y If warm air is desired at the À oor, set the
mode selector dial to the
position. 


y When the fan control dial is ON, and the
mode selector dial is in the
or
position, the air conditioner is
automatically turned on and the outside
air position is automatically selected to
defrost the windshield. In the
or
position, the outside air position cannot
be changed to the recirculated air
position.

Dehumidifying (With air
conditioner)
Operate the air conditioner in cool or cold
weather to help defog the windshield and
side windows.

1. Set the mode selector dial to the desired
position.
2. Set the air intake selector to the outside
air position (indicator light turns off).
3. Set the temperature control dial to the
desired position.
4. Set the fan control dial to the desired
speed.
5. Turn on the air conditioner by pressing
the A/C switch.

N O T E
One of the functions of the air conditioner
is dehumidifying the air and, to use
this function, the temperature does not
have to be set to cold. Therefore, set the
temperature control dial to the desired
position (hot or cold) and turn on the air
conditioner when you want to dehumidify
the cabin air.

/:A(4'#,A'FKVKQPKPFD/:A(4'#,A'FKVKQPKPFD

5–10
Interior Features
Climate Control System
Control Switches
Temperature control dial
This dial controls temperature. Turn it
clockwise for hot and counterclockwise
for cold.
Fan control dial
The fan has seven speeds.
AUTO position
The amount of airÀ ow will be
automatically controlled in accordance
with the set temperature.
Except AUTO position
The airÀ ow amount can be adjusted to the
desired level by turning the dial.
0 position
To turn off the system, set the dial to 0
position.
Mode selector dial
Turn the mode selector dial to select
airÀ ow mode (page 5-4 ).
AUTO position
The airÀ ow mode automatically adjusts to
the selected temperature.
Except AUTO position
The desired airÀ ow position can be
selected by turning the dial.
N O T E
 


y With the airÀ ow mode set to the
position and the temperature control
dial set at a medium temperature,
heated air is directed to the feet and air
at a comparably lower temperature will
À ow through the central, left and right
vents.
 


y When the fan control dial is ON, and the
mode selector dial is in the
or
position, the air conditioner is
automatically turned on and the outside
air position is automatically selected to
defrost the windshield. In the
or
position, the outside air position cannot
be changed to the recirculated air
position.

A/C switch
The air-conditioning (cooling/
dehumidifying functions) can be turned on
or off by pressing the switch while the fan
control dial is at a position other than 0.
The indicator light turns on while the air-
conditioning is operating.
N O T E
The air conditioner may not function when
the outside temperature approaches 0 °C
(32 °F).

Air intake selector
Outside or recirculated air positions can be
selected. Press the switch to select outside/
recirculated air positions.
Recirculated air position (indicator light
illuminated)
Outside air is shut off. Use this position
when going through tunnels, driving in
congested traf¿ c (high engine exhaust
areas) or when quick cooling is desired.
/:A(4'#,A'FKVKQPKPFD/:A(4'#,A'FKVKQPKPFD