2017 MAZDA MODEL CX-5 ECU

6–65
Maintenance and Care
Appearance Care
*Some models.
Active Driving Display Maintenance *
Windshield type
The dust-proof sheet has a coating. When
cleaning, do not use a hard or rough-
surface cloth, or cleaning detergent. In
addition, if a chemical solvent gets on
the active driving display, wipe it off
immediately. The dust-proof sheet could
be damaged and the surface coating could
be scratched. Use a fi ne, soft cloth such as
those used for cleaning eyeglasses.
NOTE
Use of compressed air when cleaning the
dust-proof sheet is recommended.

Auto fl ip-up type
The combiner and mirror surface have
a special coating. When cleaning it, do
not use a hard cloth, a cloth with a rough
surface, or cleaning detergent. Use a fi ne-
textured, soft cloth. .
If a chemical solvent gets on the combiner
or mirror surface, wipe it off immediately.
Otherwise, they could be damaged and the
surface coating could be scratched.
Cleaning the Window Interiors
If the windows become covered with an
oily, greasy, or waxy fi lm, clean them with
glass cleaner. Follow the directions on the
container.
CAUTION
 Do not scrape or scratch the inside of the window glass. It could damage the
thermal fi laments and the antenna lines.
 When washing the inside of the window glass, use a soft cloth dampened in
lukewarm water, gently wiping the
thermal fi laments and the antenna lines.
 Use of glass cleaning products could damage the thermal fi laments and the
antenna lines.

Cleaning the Floor Mats
Rubber fl oor mats should be cleaned with
mild soap and water only.
WARNING
Do not use rubber cleaners, such as tire
cleaner or tire shine, when cleaning
rubber fl oor mats: Cleaning the rubber fl oor mats with
rubber cleaning products makes the
fl oor mats slippery.
This may cause an accident when
depressing the accelerator, brake, or
clutch (Manual transaxle) pedal or
when getting in or out of the vehicle.

After removing the fl oor mats for cleaning,
always reinstall them securely (page
3-51 ).

CX-5_8FN1-EA-16L_Edition1.indb 652016/12/12 10:07:18

7–4
If Trouble Arises
Flat Tire
Jack
To remove the jack
1. Open the luggage board, and lift it.

2. Remove the jack.


To secure the jack
Perform the removal procedure in reverse.
Maintenance
   Always keep the jack clean.  Make sure the moving parts are kept
free from dirt or rust.
   Make sure the screw thread is
adequately lubricated.

Spare Tire
Your Mazda has a temporary spare tire.
The temporary spare tire is lighter and
smaller than a conventional tire, and is
designed only for emergency use and
should be used only for VERY short
periods. Temporary spare tires should
NEVER be used for long drives or
extended periods.
WARNING
Do not install the temporary spare tire
on the front wheels (driving wheels): Driving with the temporary spare tire
on one of the front driving wheels is
dangerous. Handling will be aff ected.
You could lose control of the vehicle,
especially on ice or snow bound roads,
and have an accident. Move a regular
tire to the front wheel and install the
temporary spare tire to the rear.

CX-5_8FN1-EA-16L_Edition1.indb 42016/12/12 10:07:19

7–6
If Trouble Arises
Flat Tire
3. For vehicles equipped with a sub-woofer, loosen the hold-down bolt and
remove the woofer and spare tire.



For vehicles not equipped with a sub- woofer, turn the spare tire hold-down
bolt counterclockwise and remove the
spare tire.

Spare tire hold-down bolt

To secure the spare tire
Store the spare tire in the reverse order
of removal. After storing, verify that the
spare tire is stored securely.
Changing a Flat Tire
NOTE
If the following occurs while driving, it
could indicate a fl at tire.
   Steering becomes dif fi cult.   The vehicle begins to vibrate
excessively.
  The vehicle pulls in one direction.
If you have a fl at tire, drive slowly to a
level spot that is well off the road and out
of the way of traf fi c to change the tire.
Stopping in traf fi c or on the shoulder of a
busy road is dangerous.
WARNING
Be sure to follow the directions for
changing a tire: Changing a tire is dangerous if not
done properly. The vehicle can slip off
the jack and seriously injure someone.
No person should place any portion
of their body under a vehicle that is
supported by a jack.

Never allow anyone inside a vehicle
supported by a jack: Allowing someone to remain in
a vehicle supported by a jack is
dangerous. The occupant could cause
the vehicle to fall resulting in serious
injury.

NOTE
Make sure the jack is well lubricated
before using it.

CX-5_8FN1-EA-16L_Edition1.indb 62016/12/12 10:07:19

7–12
If Trouble Arises
Flat Tire
5. Use the lug wrench to tighten the nuts in the order shown.



If you are unsure of how tight the nuts should be, have them inspected at an
Authorized Mazda Dealer.

Nut tightening torque
N·m (kgf·m, ft·lbf) 108—147 (12—14, 80—108)

WARNING
Always securely and correctly tighten
the lug nuts: Improperly or loosely tightened lug
nuts are dangerous. The wheel could
wobble or come off . This could result
in loss of vehicle control and cause a
serious accident.

Be sure to reinstall the same nuts you
removed or replace them with metric
nuts of the same confi guration:
Because the wheel studs and lug nuts
on your Mazda have metric threads,
using a non-metric nut is dangerous.
On a metric stud, it would not secure
the wheel and would damage the stud,
which could cause the wheel to slip off
and cause an accident.

6. (Aluminum wheel equipped vehicle)
Remove the center cap by tapping it from the backside of the wheel using
the lug wrench.
7. Store the damaged tire, using the fl at
tire hold-down bolt to hold it in place.
(With sub-woofer)


Flat tire
hold-down boltSub-woofer

(Without sub-woofer)


Flat tire
hold-down bolt

CX-5_8FN1-EA-16L_Edition1.indb 122016/12/12 10:07:21

7–16
If Trouble Arises
Battery Runs Out
1. Remove the battery cover.


2. Make sure the booster battery is 12 V and that its negative terminal is
grounded.
3. If the booster battery is in another vehicle, do not allow both vehicles
to touch. Turn off the engine of the
vehicle with the booster battery and
all unnecessary electrical loads in both
vehicles.
4. Connect the jumper cables in the exact sequence as in the illustration.
 Connect one end of a cable to the positive terminal on the discharged
battery (1).
 Attach the other end to the positive terminal on the booster battery (2).
 Connect one end of the other cable to the negative terminal of the booster
battery (3).
 Connect the other end to the ground point indicated in the illustration
away from the discharged battery (4).

5. Start the engine of the booster vehicle and run it a few minutes. Then start the
engine of the other vehicle.
6. When fi nished, carefully disconnect the
cables in the reverse order described in
the illustration. 7. If the battery cover has been removed,
install it in the reverse order of
removal.
NOTE
Verify that the covers are securely
installed.

CX-5_8FN1-EA-16L_Edition1.indb 162016/12/12 10:07:22

7–21
If Trouble Arises
Emergency Towing
*Some models.
 Do not tow with sling-type equipment. This could damage your vehicle. Use
wheel-lift or fl atbed equipment.

 If the electric parking brake (EPB) cannot be released when towing the vehicle,
transport the vehicle with all front
and rear wheels raised off the ground
as shown in the fi gure. If the vehicle is
towed without raising the wheels off
the ground, the brake system could be
damaged.

Wheel dollies

Tiedown Hooks *
CAUTION
Do not use the front and rear tiedown
eyelets for towing the vehicle.
They have been designed only for
securing the vehicle to a transport
vessel during shipping.
Using the eyelets for any other purpose
could result in the vehicle being
damaged.

Tiedown Hooks
1. Remove the tiedown eyelet and the lug wrench from the luggage compartment
(page 7-3 ).
CX-5_8FN1-EA-16L_Edition1.indb 212016/12/12 10:07:23

7–22
If Trouble Arises
Emergency Towing
2. Wrap a fl athead screwdriver or similar
tool with a soft cloth to prevent damage
to a painted bumper, and open the cap
located on the front or rear bumper.
Front


Rear

Jack lever

CAUTION
Do not use excessive force as it may
damage the cap or scratch the painted
bumper surface.

NOTE
Remove the cap completely and store it so
as not to lose it.

3. Securely install the tiedown eyelet using the lug wrench.
Front


Lug wrench
Tiedown
eyelet

Rear


Tiedown eyelet
Lug wrench

4. Hook the tying rope to the tiedown eyelet.
CAUTION
If the tiedown eyelet is not securely
tightened, it may loosen or disengage
from the bumper when tying the
vehicle. Make sure that the tiedown
eyelet is securely tightened to the
bumper.

CX-5_8FN1-EA-16L_Edition1.indb 222016/12/12 10:07:23

7–27
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.
Signal Warning


(Red)
Brake Pedal
Operation Demand Warning Light
*
When only fl ashing
Flashes if there is the possibility of the vehicle not being held in the\
stopped position by the
AUTOHOLD function, such as on steep slopes. Depress and hold your foot on t\
he brake
pedal.
When fl ashing and beep sound is activated at the same time
The warning light fl ashes and the beep sound is activated for about fi ve seconds if there is
a problem with the system. If the warning light fl ashes and the warning sound is activated,
immediately depress the brake pedal and stop using the AUTOHOLD function then contact
an Authorized Mazda Dealer.
WARNING
Immediately depress the brake pedal if the warning light fl ashes and the beep sound is
activated while using the AUTOHOLD function: Because the AUTOHOLD function is canceled forcibly, the vehicle may move
unexpectedly and result in an accident.


Check Engine Light If this light illuminates while driving, the vehicle may have a problem.\
It is important to
note the driving conditions when the light illuminated and consult an Authorized Mazda
Dealer.
The check engine light may illuminate in the following cases:
 The fuel tank level being very low or approaching empty.
 The engine's electrical system has a problem.
 The emission control system has a problem.
 The fuel- fi ller cap is missing or not tightened securely.
If the check engine light remains on, or it fl ashes continuously , do not drive at high speeds
and consult an Authorized Mazda Dealer as soon as possible.


Automatic
Transaxle Warning
Indication/Warning Light
* The indication/light illuminates when the transaxle has a problem.
CAUTION
If the automatic transaxle warning indication/light illuminates, the transaxle has
an electrical problem. Continuing to drive your Mazda in this condition could cause
damage to your transaxle. Consult an Authorized Mazda Dealer as soon as possible.


AWD Warning Indication
*
“4WD System Malfunction” is displayed
The indication is displayed under the following conditions. The system may have a
malfunction. Have the vehicle checked at an Authorized Mazda Dealer.
 When there is a malfunction in the AWD system.
 When there is a large difference between the tire size of the front and rear wheels.
“4WD System High Load” is displayed
The indication is displayed under the following conditions. Park the veh\
icle in a safe place
and check that the warning indication light turns off, and then drive the vehicle. Contact an
Authorized Mazda Dealer if the indication is continuously displayed.
 When the differential oil temperature is excessively high.
 When there is a large difference between the front and rear wheel rotation, such as when
trying to remove the vehicle from mud.
CX-5_8FN1-EA-16L_Edition1.indb 272016/12/12 10:07:25