6–24
Maintenance and Care
Owner Maintenance
Except U.S.A. and CANADA
Use SAE 5W-30 engine oil.
Oil container labels provide important
information.
A chief contribution this type of oil makes
to fuel economy is reducing the amount of
fuel necessary to overcome engine friction.
For maintenance service, Mazda
recommends Mazda Genuine Parts and
Castrol
® (Mexico only).
(ILSAC)
(Mexico)
Use SAE 5W-30 engine oil. If SAE 5W-30
engine oil is not available, use SAE 5W-20
engine oil.
The quality designation SM, or ILSAC
must be on the label.
80
60
40
20
0
–40 –20
30
100
40
20
10
0
–10
–20
–30
–40
Vehicle Engine Control Unit Reset
Procedure
After replacing the engine oil, it is
recommended to have a repair shop such
as an Authorized Mazda Dealer perform
the initialization (engine oil data resetting)
of the recorded value. If the value recorded
by the computer is not initialized, the
wrench indicator light may not turn off or
it may turn on earlier than normal.
Refer to Maintenance Monitor on page
6-16 .
CX-5_8FN1-EA-16L_Edition1.indb 242016/12/12 10:07:08
9–16
Specifi cations
Personalization Features
Item Feature Factory
Setting Available
Settings Settings
Change
Method
Fuel Economy Monitor (page 4-86 )
Ending display Display/non-display Off On/Off B —
Fuel economy
resetting procedure Linkage/non-linkage with fuel economy reset
and trip meter A reset
Off On/Off B —
Active Driving Display (page 4-28 )
Display Setting can be changed so that the Active
Driving Display is not displayed.
On On/Off C —
The display height (up/down position) can
be changed. 0 13 steps up/
down from
initial setting
(total: 27 steps) C —
The method for adjusting the display
brightness (automatically/manually) can be
changed. AUTO
AUTO/
MANUAL C —
The standard brightness while automatic
adjustment is selected can be changed using
the brightness adjustment. 0 2 steps up/
down from
initial setting
(total: 5 steps) C —
The standard brightness while manual
adjustment is selected can be changed using
the brightness adjustment. 0 20 steps up/
down from
initial setting
(total: 41 steps) C —
The display angle can be changed. 0 3steps up/down
from initial setting
(total: 7steps) C —
Navigation
guidance Display/non-display
On On/Off C —
Street Information Display/non-display On-Demand Off/Always/
On-Demand C —
*1 Though these systems can be turned Off, doing so will defeat the purpose of the system and Mazda recommends that these systems remain On.
*2 Only the volume of the warning beep during Blind Spot Monitoring (BSM)\
operation can be changed. The volume of the warning beep during Rear Cross Traf fi c Alert (RCTA) operation cannot be changed.
*3 This system functions only when the navigation system is functioning.
*4 If the auto-wiper control is set to Off, the wiper lever
position is set to intermittent operation.
*5 If the setting is changed to Off, the following operation is performed according to the headlight switc\
h position:
At position: Headlights turn off immediately after the ignition is switched off.
At any position other than : Headlights on/off conditions vary according to the headlight switch
position. Refer to Headlights on page 4-51 .
*6 When set to Off, the lights-on reminder is operable.
*7 The lights-on reminder settings can be changed at anytime, however, the lights-on reminder only operates when
the auto headlight function is set to Off. Refer to Lights-On Reminder on page 7-39 .
CX-5_8FN1-EA-16L_Edition1.indb 162016/12/12 10:07:41
