7–41
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.
Key Removed from Vehicle Warning Beep
Vehicles with advanced keyless function
If the key is taken out of the vehicle while
the ignition is not switched OFF and
all the doors are closed, the beep which
sounds outside of the vehicle will be heard
6 times, the beep which sounds inside
the vehicle will be heard 6 times, and the
KEY warning light (red) in the instrument
cluster fl ashes continuously to notify
the driver that the ignition has not been
switched OFF.
Vehicles without advanced keyless
function
If the key is taken out of the vehicle while
the ignition is not switched OFF and all
the doors are closed, a beep will be heard
in the cabin 6 times and the KEY warning
light (red) in the instrument cluster turns
on continuously to notify the driver that
the ignition has not been switched OFF.
NOTE
Because the key utilizes low-intensity
radio waves, the Key Removed From
Vehicle Warning may activate if the key is
carried together with a metal object or it
is placed in a poor signal reception area.
Request Switch Inoperable Warning Beep (With the advanced
keyless function)
If the request switch is pressed with the
door open or ajar, or the ignition is not
switched OFF with a key being carried, a
beep will be heard outside for about
2 seconds to notify the driver that the door
or liftgate cannot be locked.
Key Left-in-luggage Compartment Warning Beep (With the advanced
keyless function)
If the key is left in the luggage
compartment with all the doors locked and
the liftgate closed, a beep will be heard
outside for about 10 seconds to notify
the driver that the key is in the luggage
compartment. In this case, take out the
key by pressing the electric liftgate opener
and opening the liftgate. The key taken
out of the luggage compartment may
not operate because its functions have
been temporarily stopped. To restore the
key's functions, perform the applicable
procedure (page 3-9 ).
Key Left-in-vehicle Warning Beep (With the advanced keyless
function)
If all the doors and luggage compartment
are locked using another key while the key
is left in the cabin, the beep which sounds
outside of the vehicle will be heard for
about 10 seconds to notify the driver that
the key is in the cabin. In this case, take
out the key by opening the door. A key
taken out of the vehicle using this method
may not operate because its functions have
been temporarily stopped. To restore the
key's functions, perform the applicable
procedure (page 3-9 ).
Electronic Steering Lock Warning Beep *
The warning beep operates if the steering
wheel is not unlocked after the push button
start is pressed. (page 4-4 )
CX-5_8FN1-EA-16L_Edition1.indb 412016/12/12 10:07:29
7–42
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.
Power Liftgate Warning Beep *
If system operation precautions are
necessary, the driver is notifi ed by the
warning sound.
Cautions What to check
The beep sounds 3 times The conditions required
for the power liftgate
to operate have not
been met, such as an
object being stuck in the
liftgate.
The beep sound
continues The vehicle is being
driven with the liftgate
open. Stop the vehicle
and close the liftgate.
Electric Parking Brake (EPB)
Warning Beep
The warning buzzer is activated under the
following conditions:
The vehicle is driven with the electric
parking brake (EPB) applied.
The electric parking brake (EPB) switch
is pulled while the vehicle is driven.
AUTOHOLD Warning Beep
Warning light fl ashes/message is
displayed and beep sound is activated
simultaneously for about fi ve seconds
when using AUTOHOLD function or
when AUTOHOLD switch is operated.
Because a problem with AUTOHOLD
function has occurred, AUTOHOLD
function does not operate even if
AUTOHOLD switch is operated.
If the warning light fl ashes/message is
displayed and the beep sound is activated
simultaneously, have your vehicle
inspected at an Authorized Mazda Dealer.
Power Steering Warning Buzzer
If the power steering system has
a malfunction, the power steering
malfunction light turns on or fl ashes and
the buzzer operates at the same time.
Refer to Warning Indication/Warning
Lights on page 4-33 .
Tire Infl ation Pressure Warning
Beep *
The warning beep sound will be heard
for about 3 seconds if the tire pressures
decrease.
If the tire pressure decreases extremely,
a beep sound will be heard for
approximately 30 seconds.
Refer to Tire Pressure Monitoring System
on page 4-172 .
Blind Spot Monitoring (BSM) Warning Beep *
Driving forward
The warning beep operates when the turn
signal lever is operated to the side where
the Blind Spot Monitoring (BSM) warning
light is illuminated.
NOTE
A personalized function is available to
change the Blind Spot Monitoring (BSM)
warning beep sound volume.
Refer to Personalization Features on page
9-11 .
Reversing
If a moving object such as a vehicle or
two-wheeled vehicle approaches on the
left or right from behind your vehicle, the
Blind Spot Monitoring (BSM) warning
sound is activated.
CX-5_8FN1-EA-16L_Edition1.indb 422016/12/12 10:07:29
7–43
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
*Some models.
Lane Departure Warning Sound *
While the system is operating, if the
system determines that the vehicle may
depart from the lane, it sounds a warning
sound.
NOTE
The volume of the Lane-keep Assist
System (LAS) & Lane Departure
Warning System (LDWS) warning sound
can be changed.
Refer to Personalization Features on page 9-11 .
The type of the Lane-keep Assist System
(LAS) & Lane Departure Warning
System (LDWS) warning sound can be
changed.
Refer to Personalization Features on page 9-11 .
Collision warning *
If there is a possibility of a collision with
a vehicle ahead or an obstruction at the
rear of the vehicle, the warning light in the
instrument cluster fl ashes at the same time
as the warning indication is displayed in
the multi-information display or the active
driving display, and a warning sound is
activated intermittently.
Mazda Radar Cruise Control with Stop & Go function (MRCC with
Stop & Go function) System
Warnings
*
The Mazda Radar Cruise Control with
Stop & Go function (MRCC with Stop &
Go function) system warnings notify the
driver of system problems and precautions
on use when required. Check after hearing
a warning beep sound.
Warning beep What to check
While the Mazda Radar
Cruise Control with
Stop & Go function
(MRCC with Stop &
Go function) system is
operating, a single beep
sound is heard when
“Front radar blocked” is
displayed in the multi-
information display. Cancel the Mazda Radar
Cruise Control with
Stop & Go function
(MRCC with Stop &
Go function) system if
the radar sensor (front)
becomes dirty. Clean the
area around the radar
sensor (front).
The beep sounds
intermittently while the
vehicle is being driven. The distance between
your vehicle and the
vehicle ahead is too
close. Verify the safety
of the surrounding area
and reduce vehicle
speed.
While the Mazda Radar
Cruise Control with
Stop & Go function
(MRCC with Stop &
Go function) system is
operating, a single beep
sound is heard when
“Front radar sensor
system malfunction” is
displayed in the multi-
information display. A malfunction in the
system may be indicated.
Check the center display
to verify the problem
and then have your
vehicle inspected by
an Authorized Mazda
Dealer.
CX-5_8FN1-EA-16L_Edition1.indb 432016/12/12 10:07:29
8–26
Customer Information and Reporting Safety Defects
Tire Information (U.S.A.)
P
Indicates a tire that may be installed on cars, SUVs, minivans and light\
trucks as designated
by the Tire and Rim Association (T&RA).
NOTE
If your tire size does not begin with a letter this may mean it is designated by ei\
ther ETRTO
(European Tire and Rim Technical Organization) or JATMA (Japan Tire Manufacturing
Association).
215
“215” is the nominal width of the tire in millimeters. This three-digit number gives the
width in millimeters of the tire from sidewall edge to sidewall edge. In\
general, the larger
the number, the wider the tire.
65
“65” is the aspect ratio. This two-digit number indicates the tire's ratio of height to width.
R
“R” is the tire construction symbol. R indicates “Radial ply co\
nstruction”.
15
“15” is the wheel rim diameter in inches.
95
“95” is the Load Index. This two-or three-digit number indicates how much weight each tire
can support.
H
“H” is the speed rating. The speed rating denotes the maximum speed for which the use of
the tire is rated.
Letter Rating Speed Rating
Q 99 mph
R 106 mph
S 112 mph
T 118 mph
U 124 mph
H 130 mph
V 149 mph
W 168
* mph
Y 186 * mph
* For tires with a maximum speed capability over 149 mph, tire manufacture\
rs sometimes use the letters ZR. For tires with a maximum speed capability over 186 mph, tire manufacturers a\
lways use the letters ZR.
CX-5_8FN1-EA-16L_Edition1.indb 262016/12/12 10:07:33
8–29
Customer Information and Reporting Safety Defects
Tire Information (U.S.A.)
T
Indicates a tire that may be installed on cars, SUVs, minivans and light\
trucks as designated
by the Tire and Rim Association (T&RA).
11 5
“115” is the nominal width of the tire in millimeters. This three-digit number gives the width
in millimeters of the tire from sidewall edge to sidewall edge. In gener\
al, the larger the
number, the wider the tire.
70
“70” is the aspect ratio. This two-digit number indicates the tire's ratio of height to width.
D
“D” is the tire construction symbol. D indicates “diagonal ply \
construction”.
16
“16” is the wheel rim diameter in inches.
90
“90” is the Load Index. This two-or three-digit number indicates how much weight each tire
can support.
M
“M” is the speed rating. The speed rating denotes the maximum speed for which the use of
the tire is rated.
Letter Rating Speed Rating
M 81 mph
CX-5_8FN1-EA-16L_Edition1.indb 292016/12/12 10:07:33
9–8
Specifi cations
Specifi cations
*Some models.
Light Bulbs
Exterior light
Light bulb Category
Wattage UNECE *1 (SAE)
Headlights/Daytime running lights LED *2 — (—)
Parking lights LED type LED *2 — (—)
Front turn signal lights/Parking lights * 28/8 — (#7444NA)
Front side-marker lights LED type
LED *2 — (—)
Bulb type 5 W5W (—)
Fog lights
* LED *2 — (—)
Side turn signal lights LED *2 — (—)
High-mount brake light LED *2 — (—)
Rear turn signal lights 21 WY21W (7443NA)
Rear side-marker lights LED type
LED
*2 — (—)
Bulb type 21/5 W21/5W (7443)
Brake lights/Taillights LED type
LED
*2 — (—)
Bulb type 21/5 W21/5W (7443)
Reverse lights LED
*2 — (—)
License plate lights 5 W5W (—)
*1 UNECE stands for United Nations Economic Commission for Europe.
*2 LED is the abbreviation for Light Emitting Diode.
Interior light
Light bulb Category
Wattage UNECE *1
Luggage compartment light 8 —
Overhead light (Front)/Map lights 8 —
Rear map lights 8 —
Vanity mirror lights
* 2 —
*1 UNECE stands for United Nations Economic Commission for Europe.
*2 LED is the abbreviation for Light Emitting Diode.
CX-5_8FN1-EA-16L_Edition1.indb 82016/12/12 10:07:39
9–14
Specifi cations
Personalization Features
Item Feature Factory
Setting Available
Settings Settings
Change
Method
Vehicle
Door locks (page
3-17 ) Operation condition of auto lock/unlock
function Lock:
Driving, Unlock:
IGN Off Off/
Lock When Driving/
Lock: Driving, Unlock: IGN Off/
Lock When
Shifting Out Of P/
Lock: Shift From P,
Unlock: In P/
Lock: Driving, Unlock: In P A D
Keyless entry
system (page
3-3 ) Method for unlocking door using transmitter
Once:
Driver's,
Twice: All Doors Touch Once:
All Doors/
Once: Driver's, Twice: All Doors A E
Time for locking door automatically 60 seconds 90 seconds/
60 seconds/
30 seconds A —
Advanced keyless
entry system (page
3-10 ) Method for unlocking door using request
switch/transmitter
Once:
Driver's,
Twice: All Doors Touch Once:
All Doors/
Once: Driver's, Twice: All Doors A
E,
F
Time for locking door automatically 60 seconds 90 seconds/
60 seconds/
30 seconds A —
Auto-lock function operation/non-operational Off On/Off A —
Beep volume when locking/unlocking Medium High/
Medium/ Low/ Off A
E,
F
Illuminated entry
system (page
5-140 ) Time until interior lights turn off after
closing door
15 seconds 60 seconds/
30 seconds/
15 seconds/
7.5 seconds A —
Time until interior lights turn off
automatically when any door is not closed
completely 30 minutes 60 minutes/
30 minutes/
10 minutes A —
Auto-wiper control
(page 4-58 ) Operational/non-operational
On On/Off
*4 A —
CX-5_8FN1-EA-16L_Edition1.indb 142016/12/12 10:07:40
9–15
Specifi cations
Personalization Features
Item Feature Factory
Setting Available
Settings Settings
Change
Method
Daytime running
lights (page
4-56 ) Operational/non-operational
On On/Off — —
Auto headlight off
*5
(page 4-51 ) Time until headlights turn off
30 seconds 120 seconds/
90 seconds/
60 seconds/
30 seconds/ 0 seconds
*6 A —
Auto-light control
(page 4-51 ) Timing by which lights turn on
Medium Light/
Medium Light/ Medium/
Medium Dark/ Dark A —
High Beam Control
System (HBC)
(page 4-96 ) Operational/non-operational
*1
On On/Off A —
Adaptive Front
Lighting System
(AFS) (page
4-95 ) Operational/non-operational
*1
On On/Off A —
Lights-on
reminder
*7 (page
7-39 ) Warning beep volume
High High/Low/Off A —
Coming home light
(page 4-55 ) Time until headlights turn off
30 seconds 120 seconds/
90 seconds/
60 seconds/
30 seconds/ Off A —
Leaving home light
(page 4-55 ) Operational/non-operational
On On/Off A —
Turn signal
indicator (page
4-57 ) Beep volume
High High/Low A —
Three-fl ash turn
signal (page
4-58 ) Operational/non-operational
On On/Off A —
Rear window
defogger (page
4-62 ) The operation time for the rear window
defogger can be changed.
15 minutes 15 minutes/
Continuous
*8 — —
System
Language Language indicated in display English Depends on
market
*9 A —
Temperature Temperature unit indicated in display °F or °C °F/°C A —
Distance Distance unit indicated in display mi or km mi/km A —
CX-5_8FN1-EA-16L_Edition1.indb 152016/12/12 10:07:41