2017 MAZDA MODEL CX-5 display

CAUTION
If the KEY warning light (red)
illuminates, or the push button start
indicator light (amber) flashes, this
could indicate a problem with the
engine starting system. This may
prevent the engine from starting or
from switching the ignition to ACC or
ON (for vehicles with a type A
instrument cluster (page 4-42),
messages are displayed in the
instrument cluster). Have your vehicle
inspected at an expert repairer, we
recommend an Authorised Mazda
Repairer as soon as possible.
NOTE
•Under the following conditions, the
KEY warning light (red) flashes after
the push button start is pressed. This
informs the driver that the push
button start will not switch to ACC,
even if it is pressed from off (for
vehicles with a type A instrument
cluster (page 4-42), messages are
displayed in the instrument cluster).
•The key battery is dead.
•The key is out of operational
range.
•The key is placed in areas where it
is difficult for the system to detect
the signal (page 3-6).
•A key from another manufacturer
similar to the key is in the
operational range.
•(Forced engine starting method)
If the KEY warning light (red)
illuminates, or the push button start
indicator light (amber) flashes, this
could indicate that the engine may
not start using the usual starting
method (for vehicles with a type A
instrument cluster (page 4-42),
messages are displayed in the
instrument cluster). Have your
vehicle inspected at an expert
repairer, we recommend an
Authorised Mazda Repairer as soon
as possible. If this occurs, the engine
can be force-started. Press and hold
the push button start until the engine
starts. Other procedures necessary
for starting the engine, such as
having the key in the cabin, and
depressing the clutch pedal (manual
transaxle) or the brake pedal
(automatic transaxle) are required.
•When the engine is force-started, the
KEY warning light (red) (if
equipped) remains illuminated and
the push button start indicator light
(amber) remains flashing.
•(Automatic transaxle)
When the selector lever is in the
neutral (N) position, the KEY
indicator light (green) (if equipped)
and the push button start indicator
light (green) do not illuminate.
7. Press the push button start after both
the KEY indicator light (green) (if
equipped) in the ins trument cluster and
the push button start indicator light
(green) illuminate.
When Driving
Start/Stop Engine
4-7
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

NOTE
When touching the push button start
using the backside of the key as shown
in the illustration, touch the push
button start with the lock switch side of
the key facing up.
5. Verify that the push button start
indicator light (green) turns on.
6. Press the push button start to start the engine.
NOTE
•The engine cannot be started unless
the clutch pedal is fully depressed
(manual transaxle) or the brake
pedal is fully depressed (automatic
transaxle).
•If there is a malfunction with the
push button start function, the push
button start indica tor light (amber)
flashes. In this ca se, the engine may
start, however, have the vehicle
checked at an expert repairer, we
recommend an Authorised Mazda
Repairer as soon as possible.
•If the push button start indicator
light (green) does not illuminate,
perform the operation from the
beginning again. If it does not
illuminate, have the vehicle checked
at an expert repairer, we recommend
an Authorised Mazda Repairer.
•To switch the ignition position
without starting the engine, perform
the following operations after the
push button start indicator light
(green) turns on.
1. Release the clutch pedal (manual transaxle) or brake pedal
(automatic transaxle).
2. Press the push button start to
switch the igniti on position. The
ignition switches in the order of
ACC, ON, and off each time the
push button start is pressed. To
switch the ignition position
again, perform the operation
from the beginning.
▼ Emergency Operation for Starting
the Engine
If the KEY warning ligh
t (red) illuminates,
or the push button start indicator light
(amber) flashes, this could indicate that
the engine may not s tart using the usual
starting method (for vehicles with a type A
instrument cluster (page 4-42), messages
are displayed in the instrument cluster).
Have your vehicle inspected at an expert
repairer, we recommend an Authorised
Mazda Repairer as soon as possible. If this
occurs, the engine can be force-started.
Press and hold the push button start until
the engine starts. Other procedures
necessary for starting the engine such as
having the key in the cabin, and
depressing the clutch pedal (manual
transaxle) or the bra ke pedal (automatic
transaxle) are required.
When Driving
Start/Stop Engine
4-10
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

Turning the Engine Off
WA R N I N G
Do not stop the engine while the vehicle is
moving:
Stopping the engine while the vehicle is
moving for any reason other than in an
emergency is dangerous. Stopping the
engine while the vehicle is moving will
result in reduced braking ability due to the
loss of power braking, which could cause
an accident and serious injury.
1. Stop the vehicle completely.
2.(Manual transaxle)
Shift into neutral and set the parking
brake.
(Automatic transaxle)
Shift the selector lever to the P
position and set the parking brake.
3. Press the push button start to turn off
the engine. The ignition position is off.
CAUTION
When leaving the vehicle, make sure the
push button start is off.
NOTE
•(SKYACTIV-G 2.0, SKYACTIV-G 2.5)
The cooling fan in the engine
compartment could turn on for a few
minutes after the ignition is switched
from ON to OFF, whether or not the A/C
is on or off, to cool the engine
compartment quickly.
•If the system detects that the remaining
battery power of the key is low when the
ignition is switched from ON to ACC or
OFF, the following is indicated.
Replace with a new battery before the
key becomes unusable.
Refer to Key Battery Replacement on
page 6-41.
(Vehicle equipped with Type A
instrument cluster)
A message is indicated in the display of
the instrument cluster.
(Vehicle equipped with Type B
instrument cluster)
The KEY indicator li ght (green) flashes
for approximately 30 seconds.
Refer to Warning/Indicator Lights on
page 4-42.
•(Automatic transaxle)
If the engine is turned off while the
selector lever is in a position other than
P, the ignition switches to ACC.
▼Emergency Engine Stop
Continuously pressing the push button
start or quickly pressing it any number of
times while the engi
ne is running or the
vehicle is being driven will turn the engine
off immediately. The ignition switches to
ACC.
When Driving
Start/Stop Engine
4-11
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

Note that the vehicle may move suddenly af ter the vehicle roll prevention function is
released while the vehicle is un der the following conditions:
 The selector lever is in the N position.
 If the selector lever is shifted to the N position and the brake pedal is released while the
i-stop function is operating, the brake force is gradually released. To accelerate the
vehicle, release the brake pedal after the engi ne restarts and shift the selector lever to a
position other than the N position.
NOTE
•When the vehicle is stopped on a steep grade, the vehicle roll prevention function does not
operate because engine idling is not stopped.
•The brake pedal response may change, sound may occur from the brakes, or the brake
pedal could vibrate from the operation of the vehicle roll prevention function. However,
this does not indicate a malfunction.
▼ i-stop Warning Light (Amber)/i
-stop Indicator Light (Green)
To ensure safe and comfortable use of the vehicle, the i-stop s ystem constantly monitors the
driver's operations, the vehicle's interior and exterior enviro nment, and the operational status
of the vehicle, and uses the i-stop warning light (amber) and i -stop indicator light (green) to
inform the driver o f various cautions and warnings.
NOTE
On vehicles equipped with the centre display, the i-stop operation status is displayed in the
fuel monitor contro l status display.
Refer to Control Status Display on page 4-97.
i-stop warning light (amber)
When the light is turned on
•The light turns on when the ignition is switched ON and turns o ff when the engine is
started.
•The light turns on when the i-stop OFF switch is pressed and th e system is turned off.
•(European model)
The light turns on if the following operations are performed wh ile engine idling is
stopped. In such cases, the engine does not restart automatical ly to ensure safety. Start the
engine using the normal method.
•The bonnet is opened.
•The driver's seat belt is unfastened and the driver's door is o pened.
When Driving
Start/Stop Engine
4-19
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

Meters and Gauges

Steering Switch
Active Driving Display
Type A
(With Multi-information Display)
(Without Multi-information Display)
Instrument Cluster
Type B
(Windscreen Type) (Auto Flip-up Type)
ƒSpeedometer.................................................... ...................................................... page 4-23
„ Odometer, Trip Meter and Trip Meter Selector................... ................................. page 4-24
… Tachometer..................................................... ....................................................... page 4-25
When Driving
Instrument Cluster and Display
4-22
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

†Instrument Panel Illumin ation............................................................................... page 4-26
‡ Trip Computer and INFO Switch.................................. ........................................ page 4-28
ˆ Engine Coolant Temperature Gauge............................... ...................................... page 4-25
‰ Fuel Gauge............................................................................................................ page 4-2 6
Š Outside Temperature Display.................................... ............................................ page 4-27
‹ Cruise Control Set Vehicle Speed Display....................... ..................................... page 4-28
ΠAdjustable Speed Limiter (A SL) Display............................................................. page 4-28
 Vehicle Speed Alarm............................................................................................. page 4-30
Ž Multi-information Display and INFO Switch...................... ................................. page 4-31
 Active Driving Display......................................................................................... page 4-39
▼Speedometer
The speedometer indicates the speed of the
vehicle.
When Driving
Instrument Cluster and Display
4-23
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

▼Odometer, Trip Meter and Trip
Meter Selector (Without
Multi-information Display)
The display mode can be changed from
odometer to trip meter A to trip meter B
and then back to odometer by pressing the
selector while one of them is displayed.
The selected mode will be displayed.

Selector
Press the selector Press the selector
Press the selector
Odometer
Trip meter A
Trip meter B

Odometer
The odometer records the total distance
the vehicle has been driven.
Trip meter
The trip meter can record the total distance
of two trips. One is recorded in trip meter
A, and the other is r
ecorded in trip meter
B.

For instance, trip meter A can record the
distance from the point of origin, and trip
meter B can record the distance from
where the fuel tank is filled.

When trip meter A is s elected, pressing the
selector again within one second will
change to trip meter B mode.

When trip meter A is selected, TRIP A
will be displayed. Wh en trip meter B is
selected, TRIP B will be displayed.

The trip meter records the total distance
the vehicle is driven until the meter is
again reset. Return it to “0.0” by
depressing and holding the selector for one
second or more. Use this meter to measure
trip distances and to compute fuel
consumption.
NOTE
•(Vehicles with type B audio)
If the fuel economy data is reset using
the fuel economy monitor, or trip A is
reset using the trip meter when the
function which synchronizes the fuel
economy monitor and the trip meter is
on, the fuel economy data and trip A are
reset simultaneously.
Refer to Fuel Economy Monitor on page
4-96.
•Only the trip meters record tenths of
kilometres (miles).
•The trip record will be erased when:
•The power supply is interrupted
(blown fuse or the battery is
disconnected).
•The vehicle is driven over 9999.9 km
(mile).
When Driving
Instrument Cluster and Display
4-24
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2

▼Tachometer
The tachometer shows engine speed in
thousands of revolutions per minute (rpm).
CAUTION
Do not run the engine with the tachometer
needle in the RED ZONE.
This may cause severe engine damage.

STRIPED
ZONE
RED ZONE
*
1The range varies depending on the type
of gauge. *
1
*1
NOTE
When the tachometer needle enters the
STRIPED ZONE, this indicates to the
driver that the gears should be shifted
before entering the RED ZONE.
▼
Engine Coolant Temperature Gauge
(Without Multi-information
Display)
Displays the engine coolant temperature.
The white gauge indicates that the engine
coolant temperature is low, and the red
gauge indicates that the engine coolant
temperature is high and overheating.
CAUTION
If the engine coolant temperature gauge
indicator flashes, there is a possibility of
overheating. Park the vehicle in a safe
place immediately and take appropriate
measures. If the vehicle continues to be
driven, it could cause damage to the
engine.
Refer to Overheating on page 7-37.
NOTE
•The temperature unit (Centigrade/
Fahrenheit) of the engine coolant gauge
display changes in conjunction with the
temperature unit of the outside
temperature display.
Refer to Personalisation Features on
page 9-12.
•During normal driving, the engine
coolant temperature stabilizes at 100 °C
(210 °F) or less, and the gauge indicates
a range lower than 100 °C (210 °F).
When Driving
Instrument Cluster and Display
4-25
2017-6-7 7:51:19 Form No. CX-5 8FY4-EE-17E+L_Edition2