2017 MAZDA MODEL CX-3 coolant level

6–19
Maintenance and Care
Scheduled Maintenance
Maintenance Interval Number of months or kilometers, whichever comes ¿ rst
Months 39 42 45 48 51 54 57 60 63 66 69 72
×1000 km 65
70 75 80 85 90 95
100 105 110 115 120
Wa s h e r À uid level I I I I I I
Emergency À at tire repair kit (if installed)
*6 Inspect annually.
AIR CONDITIONER SYSTEM
Cabin air ¿ lter R R R
Chart symbols:
I : Inspect: Inspect and clean, repair, adjust, ¿ ll up, or replace if necessary.
R : Replace
L : Lubricate
C : Clean
T : Tighten
Remarks:
*1 Use of FL-22 is recommended when replacing engine coolant. Using engine coolant other than FL-22 may
cause serious damage to the engine and cooling system.
*2 According to state/provincial and federal regulations, failure to perform maintenance on these items will not
void your emissions warranties. However, Mazda recommends that all maintenance services be performed at the
recommended time or kilometer period to ensure long-term reliability.
*3 The Tire Pressure Monitoring System (TPMS) initialization must be performed so that the system operates
normally (if equipped).
*4 If the vehicle is operated primarily under any of the following conditions, replace the rear differential oil at
every 45,000 km.
a) Towing a trailer or using a car-top carrier
b) Driving in dusty, sandy or wet conditions
c) Extended periods of idling or low speed operation
d) Repeated short trips of less than 16 km
*5 If this component has been submerged in water, the oil should be replaced.
*6 Check the tire repair À uid expiration date every year when performing the periodic maintenance. Replace the
tire repair À uid bottle with new one before the expiration date.


%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

6–22
Maintenance and Care
Owner Maintenance
Owner Maintenance Precautions
T h e o w n e r o r a q u a l i¿ ed service technician should make these vehicle inspections at the
indicated intervals to ensure safe and dependable operation.

Bring any problem to the attention of an Authorized Mazda Dealer or quali¿ ed service
technician as soon as possible.
When Refueling
 




y Brake À uid level (page 6-32 )



y Engine coolant level (page 6-30 )



y Engine oil level (page 6-30 )



y Wa s h e r À uid level (page 6-32 )
At Least Monthly






y Tire inÀ ation pressures (page 6-42 )
At Least Twice a Year (For Example, Every Spring and Fall)
You can do the following scheduled maintenance items if you have some mechanical ability
and a few basic tools and if you closely follow the directions in this manual.
 


y Engine coolant (page 6-30 )



y Engine oil (page 6-27 )

Improper or incomplete service may result in problems. This section gives instructions only
for items that are easy to perform.

As explained in the Introduction (page 6-2 ), several procedures can be done only by a
quali¿ ed service technician with special tools.

Improper owner maintenance during the warranty period may affect warranty coverage.
Refer to Introduction (page 6-2 ) for owner's responsibility in protecting your investment.
For details, read the separate Mazda Warranty statement provided with the vehicle. If you
are unsure about any servicing or maintenance procedure, have it done by an Authorized
Mazda Dealer.

There are strict environmental laws regarding the disposal of waste oil and À uids. Please
dispose of your waste properly and with due regard to the environment.

We recommend that you entrust the oil and À uid changes of your vehicle to an Authorized
Mazda Dealer.
%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

6–30
Maintenance and Care
Owner Maintenance
Inspecting Engine Oil Level
1. Be sure the vehicle is on a level
surface.
2. Warm up the engine to normal
operating temperature.
3. Turn it off and wait at least 5 minutes
for the oil to return to the oil pan.
4. Pull out the dipstick, wipe it clean, and
reinsert it fully.


MAX
MINOK

5. Pull it out again and examine the level.
The level is normal if it is between the
MIN and MAX marks.
If it is near or below MIN, add enough
oil to bring the level to MAX.
CAUTION
Do not overfi ll the engine oil. This may
cause engine damage.

6. Make sure the O-ring on the dipstick is
positioned properly before reinserting
the dipstick.
7. Reinsert the dipstick fully.

Engine Coolant
Inspecting Coolant Level
WARNING
Do not use a match or live fl ame in the
engine compartment. DO NOT ADD
COOLANT WHEN THE ENGINE IS HOT:
A hot engine is dangerous. If the
engine has been running, parts of the
engine compartment can become very
hot. You could be burned. Carefully
inspect the engine coolant in the
coolant reservoir, but do not open it.


Pull over to a safe location, then
switch the ignition off and make sure
the fan is not running before attempting
to work near the cooling fan:
Working near the cooling fan when it
is running is dangerous. The fan could
continue running indefi nitely even if
the engine has stopped and the engine
compartment temperature is high. You
could be hit by the fan and seriously
injured.


Do not remove either cooling
system cap when the engine and
radiator are hot:
When the engine and radiator are hot,
scalding coolant and steam may shoot
out under pressure and cause serious
injury.

%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

6–31
Maintenance and Care
Owner Maintenance
N O T E
Changing the coolant should be done by
an Authorized Mazda Dealer.

Inspect the antifreeze protection and
coolant level in the coolant reservoir at
least once a year—at the beginning of the
winter season—and before traveling where
temperatures may drop below freezing.

Inspect the condition and connections of
all cooling system and heater hoses.
Replace any that are swollen or
deteriorated.

The coolant should be at full in the
radiator and between the F and L marks
on the coolant reservoir when the engine
is cool.


Cooling system cap Coolant reservoir
Cooling fan

If it is at or near L, add enough coolant to
the coolant reservoir to provide freezing
and corrosion protection and to bring the
level to F.
Securely tighten the coolant reservoir tank
cap after adding coolant.
CAUTION
 


¾ Radiator coolant will damage paint.
 Rinse it off quickly if spilled. 



¾ Use only soft (demineralized) water in
the coolant mixture. Water that contains
minerals will cut down on the coolant's
eff ectiveness.




¾ Do not add only water. Always add a
proper coolant mixture.
 


¾ The engine has aluminum parts and
must be protected by an ethylene-glycol-
based coolant to prevent corrosion and
freezing.
 


¾ DO NOT USE coolants Containing
Alcohol, methanol, Borate or Silicate.
  These coolants could damage the
cooling system.
 


¾ DO NOT MIX alcohol or methanol with
the coolant. This could damage the
cooling system.
 


¾ Do not use a solution that contains more
than 60% antifreeze.
  This would reduce eff ectiveness. 



¾ If the “FL22” mark is shown on or near
the cooling system cap, use of FL-22 is
recommended when replacing engine
coolant. Using engine coolant other
than FL-22 may cause serious damage to
the engine and cooling system.




If the coolant reservoir is empty or new
coolant is required frequently, consult an
Authorized Mazda Dealer.
%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

7–22
If Trouble Arises
Overheating
O v e r h e a t i n g
If the high engine coolant temperature
warning light turns on, the vehicle loses
power, or you hear a loud knocking or
pinging noise, the engine is probably too
hot.
WARNING
Pull over to a safe location, then
switch the ignition off and make sure
the fan is not running before attempting
to work near the cooling fan:
Working near the cooling fan when it
is running is dangerous. The fan could
continue running indefi nitely even if
the engine has stopped and the engine
compartment temperature is high. You
could be hit by the fan and seriously
injured.


Do not remove either cooling
system cap when the engine and
radiator are hot:
When the engine and radiator are hot,
scalding coolant and steam may shoot
out under pressure and cause serious
injury.

Open the hood ONLY after steam is no
longer escaping from the engine:
Steam from an overheated engine is
dangerous. The escaping steam could
seriously burn you.

If the high engine coolant temperature
warning light turns on:


1. Drive safely to the side of the road and
park off the right-of-way.
2. Shift into park (P).
3. Apply the parking brake.
4. Turn off the air conditioner.
5. Check whether coolant or steam is
escaping from the engine compartment.

If steam is coming from the engine
compartment:
Do not go near the front of the vehicle.
Stop the engine.
Wait until the steam dissipates, then
open the hood and start the engine.

If neither coolant nor steam is
escaping:
Open the hood and idle the engine until
it cools.
CAUTION
If the cooling fan does not operate
while the engine is running, the engine
temperature will increase. Stop the
engine and call an Authorized Mazda
Dealer.

6. Make sure the cooling fan is operating,
then turn off the engine after the
temperature has decreased.
7. When cool, check the coolant level.
If it is low, look for coolant leaks from
the radiator and hoses.


%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

9–5
Speci¿ cations
Speci¿ cations
Capacities

(Approximate Quantities)
Item Capacity
Engine oil With oil ¿ lter replacement 4.2 L (4.4 US qt, 3.7 Imp qt)
Without oil ¿ lter replacement 4.0 L (4.2 US qt, 3.5 Imp qt)
Coolant U.S.A. and Canada 5.8 L (6.1 US qt, 5.1 Imp qt)
Mexico 6.1 L (6.4 US qt, 5.4 Imp qt)
Automatic transaxle À uid 7.8 L (8.2 US qt, 6.9 Imp qt)
Transfer case oil 0.40 L (0.42 US qt, 0.35 Imp qt)
Rear differential oil 0.35 L (0.37 US qt, 0.31 Imp qt)
Fuel tank 2WD 48.0 L (12.7 US gal, 10.6 Imp gal)
AW D U.S.A. and Canada 45.0 L {11.9 US gal, 9.90 Imp gal}
Mexico 44.0 L (11.6 US gal, 9.68 Imp gal)
Check oil and À uid levels with dipsticks or reservoir gauges.

Dimensions
U.S.A. and Canada
Item Vehicle speci¿ cation
Overall length 4,275 mm (168.3 in)
Overall width 1,765 mm (69.5 in)
Overall height 1,550 mm (61.0 in)
Front tread 1,525 mm (60.0 in)
Rear tread 1,520 mm (59.8 in)
Wheelbase 2,570 mm (101.2 in)



Mexico
Item Vehicle speci¿ cation
Overall length 4,275 mm (168.3 in)
Overall width 1,765 mm (69.5 in)
Overall height 1,545 mm (60.8 in)
Front tread 1,525 mm (60.0 in)
Rear tread 1,520 mm (59.8 in)
Wheelbase 2,570 mm (101.2 in)

%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

10–5
Ignition
Switch .............................................. 4-4
Ignition not switched off (STOP) warning
beep ..................................................... 7-40
Illuminated Entry System ................. 5-131
Immobilizer System ............................ 3-37
Indicator Lights ................................... 4-27
Low engine coolant temperature ... 4-29
Wrench .......................................... 4-29
Inspecting Brake Fluid Level .............. 6-32
Inspecting Coolant Level .................... 6-30
Inspecting Engine Oil Level ............... 6-30
Inspecting Washer Fluid Level............ 6-32
Instrument Cluster ............................... 4-12
Interior Care ........................................ 6-65
Active driving display
maintenance................................... 6-67
Cleaning the À oor mats ................. 6-68
Cleaning the window interiors ...... 6-68
Instrument panel top maintenance ... 6-67
Leather upholstery maintenance ... 6-66
Panel maintenance ......................... 6-67
Plastic part maintenance ................ 6-67
Seat belt maintenance .................... 6-65
Upholstery and synthetic leather
maintenance................................... 6-66
Vinyl upholstery maintenance ....... 6-66
Interior Lights ................................... 5-130
Luggage Compartment Light ...... 5-130
Map Lights .................................. 5-130
Overhead Lights .......................... 5-130
J
Jack ....................................................... 7-5
Jump-Starting ...................................... 7-18
K
Key Suspend Function .......................... 3-8
Key left-in-luggage compartment warning
beep (With the advanced keyless
function) .............................................. 7-41 Key left-in-vehicle warning beep (With the
advanced keyless function) ................. 7-41
Keyless Entry System ........................... 3-3
Key removed from vehicle warning
beep ..................................................... 7-41
Keys ...................................................... 3-2
Key suspend function ...................... 3-8
Transmitter ...................................... 3-4
L
Label Information ................................. 9-2
Lane-Change Signals .......................... 4-47
Lane Departure Warning System
(LDWS) ............................................... 4-74
LDWS switch ................................ 4-77
Lane Departure Warning System (LDWS)
warning sound ..................................... 7-42
Laser Sensor ...................................... 4-117
Leaving Home Light ........................... 4-45
Liftgate ................................................ 3-20
Luggage compartment ................... 3-22
When Liftgate Cannot be Opened ... 7-44
Light Bulbs
Replacement .................................. 6-46
Speci¿ cations .................................. 9-7
Lighting Control.................................. 4-41
Lights-on reminder .............................. 7-39
Lubricant Quality .................................. 9-4
Luggage Compartment Light ............ 5-130
M
Maintenance
Information ...................................... 6-2
Scheduled ........................................ 6-4
Maintenance Monitor .......................... 6-20
Map Lights ........................................ 5-130
Mazda Radar Cruise Control (MRCC) ... 4-92
Close proximity warning ............... 4-95
Cruise control function ................ 4-100
Display indication ......................... 4-95
Setting the system ......................... 4-96
Index
%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD