2017 MAZDA MODEL CX-3 buttons

5–80
Interior Features
Bluetooth®
N O T E
 


y If a Bluetooth ® device has already been
paired to the vehicle as a hands-free
mobile phone, it does not need to be
paired again when using the device as
a Bluetooth
® audio device. Conversely,
it does not need to be paired again as
a hands-free mobile phone if it has
already been paired as a Bluetooth
®
audio device.
 


y Device registration can also be done
using voice recognition.

Concerning the operation of a Bluetooth ®
audio device itself, refer to its instruction
manual.
Some Bluetooth
® audio devices have PIN
codes (four digits). Refer to the audio
device's instruction manual because the
pairing procedure differs depending on
whether it has a PIN code or not.
Pairing a Bluetooth
® audio device which
has a four-digit PIN code
1. Using the audio control dial, select
the pairing mode “ PAIR DEVICE ”
in the “ BT SETUP ” mode. (Refer to
“Bluetooth
® audio device set-up” for
details.)
2. Press the audio control dial to
determine the mode. After “ ENTER
PIN ” is displayed on the audio display
for three seconds, “ PIN 0000 ” is
displayed and the PIN code can be
input. 3. Input the PIN code of your Bluetooth
®
audio device by pressing channel preset
buttons 1 to 4 while “ PIN 0000 ” is
displayed.
Press channel preset button 1 to input
the ¿ rst digit, 2 for the second, 3 for the
third, and 4 for the forth. For example,
if the PIN code were “4213” press
channel preset button 1 four times (1,
2, 3, 4), button 2 twice (1, 2), button
3 once (1), and button 4 three times
(1, 2, 3). If the “ PIN 0000 ” display
disappears before ¿ nishing the PIN
code input, repeat the procedure from
Step 1.
N O T E
Some devices accept only a particular
pairing code (Usually, “0000” or
“1234”).
If pairing cannot be completed, refer to the
owner's manual of your mobile device, and
try those numbers if necessary.

4. Press the audio control dial while
the input PIN code is displayed.
“ PAIRING ” À ashes on the audio
display.
5. Operate the Bluetooth
® audio device
and set it to the pairing mode while
“ PAIRING ” is À ashing.
6. When the pairing is completed,
and
“ PAIR SUCCESS ” are displayed after
about 10-30 seconds, after which
“ PAIR SUCCESS ” continues to be
displayed for three seconds, and then
the unit returns to the normal display.
%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

6–39
Maintenance and Care
Owner Maintenance
Battery Maintenance

To get the best service from a battery:
 


y Keep it securely mounted.



y Keep the top clean and dry.



y Keep terminals and connections clean,
tight, and coated with petroleum jelly or
terminal grease.
 


y Rinse off spilled electrolyte immediately
with a solution of water and baking
soda.
 


y If the vehicle will not be used for an
extended time, disconnect the battery
cables and charge the battery every six
weeks.

Battery Replacement
Contact an Authorized Mazda Dealer for a
battery replacement purchase.
Key Battery Replacement
If the buttons on the transmitter are
inoperable and the operation indicator
light does not À ash, the battery may be
dead.
Replace with a new battery before the
transmitter becomes unusable.
CAUTION
 


¾ Make sure the battery is installed
correctly. Battery leakage could occur if it
is not installed correctly.
 


¾ When replacing the battery, be careful
not to touch any of the internal circuitry
and electrical terminals, bend the
electrical terminals, or get dirt in the
transmitter as the transmitter could be
damaged.
 


¾ There is the danger of explosion if the
battery is not correctly replaced.
 


¾ Dispose of used batteries according to
the following instructions.
 


¾ Insulate the plus and minus terminals
of the battery using cellophane or
equivalent tape.
 


¾ Never disassemble.



¾ Never throw the battery into fi re or
water.
 


¾ Never deform or crush. 



¾ Replace only with the same type battery
(CR2025 or equivalent).

%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD

6–40
Maintenance and Care
Owner Maintenance
The following conditions indicate that the
battery power is low:
 


y The KEY indicator light (green) À ashes
in the instrument cluster for about 30
seconds after the engine is turned off.
 


y The system does not operate and
the operation indicator light on the
transmitter does not À ash when the
buttons are pressed.
 


y The system's operational range is
reduced.

Replacing the battery at an Authorized
Mazda Dealer is recommended to prevent
damage to the key. If replacing the battery
by yourself, follow the instruction.
Replacing the key battery
1. Press the knob and pull out the
auxiliary key.

Knob
2. Twist a tape-wrapped À athead
screwdriver in the direction of the
arrow and open the cover slightly.

Cover

3. Insert the tape-wrapped À athead
screwdriver into the gap and slide it in
the direction of the arrow.

Cover
Gap

4. Twist the À athead screwdriver in the
direction of the arrow and remove the
cover.

Cover

%:A(*'#'A'FKVKQPKPFD%:A(*'#'A'FKVKQPKPFD