2017 MAZDA MODEL CX-3 seat adjustment

2–4
Essential Safety Equipment
Seats
CAUTION
  When operating a seat, be careful not to put your hands or ¿ ngers near the moving
parts of the seat or on the side trim to prevent injury.
  When moving the seats, make sure there is no cargo in the surrounding area. If the
cargo gets caught it could damage the cargo.
  (Manual Seat)  When moving the seats forward and rearward or returning a rear-reclined seatback
to its upright position, make sure you hold onto the seatback with your hand while
operating. If the seatback is not held, the seat will move suddenly and could cause
injury.
NOTE
  When returning a rear seat to its original position, place the seat belt in its normal
position. Verify that the seat belt pulls out and retracts.
 
 (Power Seat)  The seat-bottom power adjustment is operated by motors. Avoid extended operation
because excessive use can damage the motors.
 


 To prevent the battery from running down, avoid using the power adjustment when
the engine is stopped. The adjuster uses a large amount of electrical power.
 


 Do not use the switch to make more than one adjustment at a time.

 
 When getting in and out of the vehicle, your foot could accidentally contact the seat
height adjustment lever and cause the seat to lower.
 Adjust the seat to obtain the correct driving position.

2–5
Essential Safety Equipment
Seats
*Some models.
Front Seat
Seat Operation

Power operation


Seat Slide
(Manual Seat)
To move a seat forward or backward, raise the lever and slide the seat to the desired position
and release the lever.
Make sure the lever returns to its original position and the seat is locked in place by
attempting to push it forward and backward.
(Power Seat)
To slide the seat, move the slide lifter switch on the outside of the seat to the front or back
and hold it. Release the switch at the desired position.

Height Adjustment *

(Manual Seat)
To adjust the seat height, move the lever up or down.
(Power Seat)
To adjust the seat height, move the switch up or down.

Height Adjustment for Front Edge of Seat Bottom (Driver's Power Seat)
To adjust the front height of the seat bottom, raise or lower the front of the slide lifter
switch.

2–6
Essential Safety Equipment
Seats
Seat Recline
(Manual Seat)
To change the seatback angle, lean forward slightly while raising the lever. Then lean back
to the desired position and release the lever.
Make sure the lever returns to its original position and the seatback is locked in place by
attempting to push it forward and backward.
(Power Seat)
To change the seatback angle, press the front or rear side of the reclining switch. Release the
switch at the desired position.

Lumbar Support Adjustment (Driver's Power Seat)
To increase the seat ¿ rmness, press and hold the front part of the switch to the desired
position, then release it.
Press the rear part of the switch to decrease ¿ rmness.

2–7
Essential Safety Equipment
Seats
*Some models.
Driving Position Memory *
The desired driving position can be called
up after programming the position.
The following driving positions can be
programmed.
 


 Driver’s seat position (seat slide, height
adjustment, front edge of seat bottom,
seat recline)
  Refer to Seat Operation on page 2-5 .



 Active driving display (display position,
brightness level, display information)
  Refer to Active Driving Display on page
4-33 .

CAUTION
Do not place ¿ ngers or hands around
the bottom of the seat while the seat
memory function is operating. The
seat moves automatically while the
seat memory function is operating and
¿ ngers or hands could get pinched and
injured.

SET button

The driving position can be programmed
or operated using the buttons on the side
of the seat or the key.
NOTE
  Lumbar support adjustment cannot
be programmed.
  Individual seat positions can be
programmed to the two available
programming buttons on the side
of the driver's seat, plus one seat
position for each registered key.
  If the vehicle has been serviced and
the battery leads disconnected, the
programmed seat positions will have
been erased. Re-programme the seat
positions.
Programming
1. Make sure the parking brake is on.
2. (Automatic transaxle)
Make sure the selector lever is in the P
position.
3. Start the engine.
4. Adjust the seat and the active driving
display to the desired driving position.
5. Press the SET button on the seat until a
beep sound is heard one time.
6. Perform one of the following settings
within 5 seconds of completing step 5
above:
 

 
 Programming using a button on
the side of the seat

 Press the button you want to
programme, either button 1 or 2, until
a beep sound is heard one time.
 

 
 Programming using the key 
 Press the key button until a beep
sound is heard one time.

NOTE
If a beep sound is heard three times, the
operation is cancelled.

2–8
Essential Safety Equipment
Seats
To move the driving position to a
programmed position
(Using a button on the side of the seat)
1. Make sure the parking brake is on.
2. (Automatic transaxle)
Make sure the selector lever is in the P
position.
3. Start the engine.
4. Press the programming button for the
driving position you want to call up
(button 1 or 2).
5. A beep sound is heard when the driving
position adjustment is completed.

NOTE
  If the driving position movement is
not changed, only the beep sounds.
  A seat position can be called up even
with the engine not running.
  The driving position adjustment is
cancelled in the following cases:
 


 Any of the seat adjustment
switches is operated.
 


 The SET button is pressed.



 Programming button 1 or 2 is
pressed.
 


 The key button or button is
operated.
 


 The vehicle starts moving.



 The active driving display is
adjusted. (Using a programmed key)
1. Unlock the doors by pressing a request
switch or the key
button.
2. After unlocking the doors, the seat
position adjustment begins within
40 seconds of opening the driver's door,
and a beep sounds when the operation
is ¿ nished.
3. Make sure the parking brake is on.
4. (Automatic transaxle)
Make sure the selector lever is in the P
position.
5. Start the engine.
6. The active driving display adjustment
begins.

NOTE
  If there is no driving position
movement, a beep is not heard.
  The driving position adjustment is
cancelled in the following cases:
 


 Any of the seat adjustment
switches is operated.
 


 The SET button is pressed.



 Programming button 1 or 2 is
pressed.
 


 The key button or button is
operated.
 


 The vehicle starts moving.



 The active driving display is
adjusted.

2–13
Essential Safety Equipment
Seats
Head Restraints
Your vehicle is equipped with head
restraints on all outboard seats and the
rear centre seat. The head restraints are
intended to help protect you and the
passengers from neck injury.
WARNING
Always drive with the head restraints
installed when seats are being used and
make sure they are properly adjusted.
In addition, always raise the head
restraints on all rear seat when they are
being used:
Driving with the head restraints
adjusted too low or removed is
dangerous. With no support behind
your head, your neck could be seriously
injured in a collision.
Height Adjustment
Adjust the head restraint so that the centre
is even with the top of the passenger's ears.



To raise a head restraint, pull it up to the
desired position.
To lower the head restraint, press the stop-
catch release, then push the head restraint
down.
Front outboard seat



Rear outboard seat



Rear centre seat

3–37
Before Driving
Mirrors
Rearview Mirror
WARNING
Do not stack cargo or objects higher
than the seatbacks:
Cargo stacked higher than the
seatbacks is dangerous. It can block
your view in the rearview mirror, which
might cause you to hit another car
when changing lanes.
Rearview mirror adjustment
Before driving, adjust the rearview mirror
to centre on the scene through the rear
window.


Reducing glare from headlights
Adjust the mirror with the antidazzle lever
in the day position.
Push the antidazzle lever forward for day
driving. Pull it back to reduce glare of
headlights from vehicles at the rear.

Antidazzle lever
Day Night

10–7
Index
Lubricant Quality .................................. 9-6
Luggage Compartment Light ............ 5-158
M
Maintenance
Information ...................................... 6-2
Scheduled ........................................ 6-3
Maintenance Monitor .......................... 6-14
Map Lights ........................................ 5-158
Mazda ERA-GLONASS ....................... 7-2
Mazda Radar Cruise Control
(MRCC) ............................................ 4-142
Close proximity warning ............. 4-146
Cruise control function ................ 4-152
Display indication ....................... 4-145
Setting the system ....................... 4-146
Shift-up/shift-down request
display ......................................... 4-151
Mazda Radar Cruise Control (MRCC)
System warnings ................................. 7-68
Message Indicated on Display ............ 7-62
Meters and Gauges .............................. 4-24
Mirror Defogger .................................. 4-76
Mirrors
Outside mirrors.............................. 3-34
Rearview mirror ............................ 3-37
O
Odometer and Trip Meter .................... 4-25
Outside Mirrors ................................... 3-34
Outside Temperature Display .............. 4-29
Outside temperature warning beep ..... 7-67
Overhead Console ............................. 5-163
Overhead Lights ................................ 5-158
Overheating ......................................... 7-42
Owner Maintenance
Closing the Bonnet ........................ 6-19
Engine Compartment Overview .... 6-20
Key battery replacement ............... 6-37
Opening the Bonnet....................... 6-18
Owner Maintenance Precautions... 6-16
P
Parking Brake ...................................... 4-80
Parking Sensor System ..................... 4-212
Park assist sensor system
operation ...................................... 4-215
Sensor detection range ................ 4-214
Personalisation Features ...................... 9-13
Power Steering .................................. 4-100
Power Windows .................................. 3-38
Power steering warning buzzer ........... 7-67
R
Radar Sensor (Front) ......................... 4-186
Radar Sensors (Rear) ........................ 4-189
Rear Coat Hooks ............................... 5-167
Rear Cross Traf¿ c Alert (RCTA) ...... 4-137
Rear Door Child Safety Locks ............ 3-20
Rear Seat ............................................. 2-10
Rear View Monitor............................ 4-203
Displayable range on the screen ... 4-205
Picture quality adjustment ........... 4-211
Rear view monitor operation ....... 4-207
Rear view parking camera
location ........................................ 4-204
Switching to the rear view monitor
display ......................................... 4-204
Variance between actual road conditions
and displayed Image
.................... 4-210
Viewing the display ..................... 4-206
Rear Window Defogger ...................... 4-75
Rear Window Washer .......................... 4-74
Rear Window Wiper ............................ 4-74
Rearview Mirror .................................. 3-37
Recommended Oil .............................. 6-22
Recording of Vehicle Data .................... 8-5
Registering Your Vehicle in A Foreign
Country ................................................. 8-2