2017 MAZDA MODEL CX-3 ECO mode

4–16
When Driving
Start/Stop Engine
 


 (Automatic transaxle) 


 
 The vehicle is stopped on a steep incline.


 
 The steering wheel is not in the straight-ahead position while the vehicle is stopped. 



 (SKYACTIV-D 1.5) 


 
 The particulate matter (PM) is being removed by the diesel particulate ¿ lter (DPF).


 
 The fuel injection amount learning is being performed. (The i-stop indicator light (green)
turns off when the vehicle speed before stopping is approx. 10 km/h (6.2 mph) or less
and fuel injection amount learning is performed while the vehicle is stopped.)


NOTE
Under the following conditions, a period of time is required to stop engine idling 

 The battery power is depleted for some reasons such as the vehicle has not been driven
for a long period.
  The ambient temperature is high or low. 
 After the battery terminals are disconnected for some reasons such as for battery
replacement.
  (SKYACTIV-D 1.5)  After PM removal is performed by the diesel particulate ¿ lter (DPF).

Engine does not restart
If the following operations are performed while the idling is stopped, the engine will not
restart for safety reasons. In such cases, start the engine using the normal method.
 
 The bonnet is opened. 
 (European model)  The driver's seat belt is unfastened and the driver's door is opened. 
 (Except European model) 



 (Manual transaxle) 
 With the shift lever in a position other than neutral, the driver's seat belt is
unfastened and the driver's door is opened.
 


 (Automatic transaxle)  With the selector lever in the D or M (not in second gear ¿ xed mode), the driver's
seat belt is unfastened and the driver's door is opened.


Engine-stop period is short or time until next engine idle stop is long 

 The ambient temperature is high or low. 
 The battery power is depleted. 
 Power consumption by the vehicle's electrical parts is high.

4–17
When Driving
Start/Stop Engine
NOTE

Engine restarts automatically while engine idling is stopped
Under the following conditions, the engine restarts automatically.
 
 The i-stop OFF switch is pressed until the beep sounds.

 The air conditioner is operated with the airÀ ow mode dial in the position. 
 (Automatic air-conditioning) 



 The temperature setting dial of the air conditioner is set to the maximum heating/
maximum cooling (A/C ON).
 


 The cabin temperature is largely different from the set temperature of the air
conditioner.
 
 The brakes are released slightly on a slope and the vehicle begins to move. 
 Two minutes have elapsed since the idling was stopped. 
 The battery power is depleted. 
 (Automatic transaxle) 



 The accelerator pedal is depressed with the selector lever in the D or M (not in
second gear ¿ xed mode) position.




 The selector lever is shifted to the R position.



 The selector lever is shifted from N or P position to D or M (not in second gear ¿ xed
mode) position.
 


 The steering wheel is operated with the selector lever in the D or M (not in second
gear ¿ xed mode) position.




 The selector lever is in the M position and the second gear ¿ xed mode is selected. 

 (Except European model) 



 (Manual transaxle) 
 With the shift lever in the neutral position, the driver's seat belt is unfastened and the
driver's door is opened.
 


 (Automatic transaxle)  With the selector lever in the N or P position, the driver's seat belt is unfastened and
the driver's door is opened.

4–18
When Driving
Start/Stop Engine
NOTE

Selector lever is operated while engine idling is stopped (automatic transaxle)
If the selector lever is shifted from D or M (not in second gear ¿ xed mode) position to
N or P position while engine idling is stopped, the engine does not restart even when the
brake pedal is released. The engine will restart if the brake pedal is depressed again or the
selector lever is shifted to the D, M (not in second gear ¿ xed mode), or R position. (For
the purposes of safety, always keep the brake pedal depressed when shifting the selector
lever while engine idling is stopped.)
 
 (European model)  If the selector lever is shifted from the D or M (not in second gear ¿ xed mode) position
to the N or P position, and the driver's seat belt is unfastened and the driver's door is
opened, the engine does not restart. Start the engine using the normal method.
  (Except European model)  If the selector lever is shifted from the D or M (not in second gear ¿ xed mode) to the
N or P position, and the driver's seat belt is unfastened and the driver's door is opened,
the engine restarts.

Battery terminals are disconnected
Engine idling may not stop right after the battery terminals are disconnected. In addition,
if the battery is replaced, the i-stop functions must be veri¿ ed. Consult an expert repairer,
we recommend an Authorised Mazda Repairer.
i-stop Warning Light (Amber)/i-stop Indicator Light (Green)

To ensure safe and comfortable use of the vehicle, the i-stop system constantly monitors the
driver's operations, the vehicle's interior and exterior environment, and the operational status
of the vehicle, and uses the i-stop warning light (amber) and i-stop indicator light (green) to
inform the driver of various cautions and warnings.
NOTE
On vehicles equipped with the centre display, the i-stop operation status is displayed in the
fuel monitor control status display.
Refer to Control Status Display on page 4-92 .

4–19
When Driving
Start/Stop Engine
i-stop warning light (amber)
When the light is turned on
 




 The light turns on when the ignition is switched ON and turns off when the engine is
started.
 


 The light turns on when the i-stop OFF switch is pressed and the system is turned off.



 The light turns on if the following operations are performed while engine idling is
stopped. In such cases, the engine does not restart automatically to ensure safety. Start the
engine using the normal method.
 

 
 The bonnet is opened.


 
 (European model) 
 The driver's seat belt is unfastened and the driver's door is opened.


 
 (Except European model) 


 
 (Manual transaxle) 
 With the shift lever in a position other than neutral, the driver's seat belt is unfastened
and the driver's door is opened.
 

 
 (Automatic transaxle) 
 With the selector lever in the D or M (not in second gear ¿ xed mode) position, the
driver's seat belt is unfastened and the driver's door is opened.



NOTE
A problem in the system may be indicated under the following conditions. Have your
vehicle inspected at an expert repairer, we recommend an Authorised Mazda Repairer.
 
 The light does not turn on when the ignition is switched ON. 
 The light continues to remain on even though the i-stop OFF switch has been pressed
while the engine is running.
When the light is À ashing
The light continues to À ash if the system has a malfunction. Have your vehicle inspected at
an expert repairer, we recommend an Authorised Mazda Repairer.

4–20
When Driving
Start/Stop Engine
i-stop indicator light (green)
When the light is turned on
 




 The light turns on while engine idling is stopped and turns off when the engine is
restarted.
 


 (Except European model) 
 The light turns on when the engine idling stop conditions are met while the vehicle is
driven.

When the light is À ashing






 (Manual transaxle) 
 The light À ashes when the shift lever is shifted to a position other than the neutral while
engine idling is stopped to notify the driver that engine idling is stopped.
  (SKYACTIV-G 2.0) 
 By depressing the clutch pedal or starting to release it, the engine restarts automatically
and the light turns off.
  (SKYACTIV-D 1.5) 
 By depressing the clutch pedal, the engine restarts automatically and the light turns off.



 (European model) 


 
 The light À ashes when the driver's door is opened while engine idling is stopped to
notify the driver that engine idling is stopped. It turns off when the driver's door is
closed.
 

 
 If the engine is restarted due to low battery voltage while the engine idling is stopped,
the i-stop indicator light (green) in the instrument cluster À ashes for about 3 seconds.




 (Except European model) 


 
 (Automatic transaxle) 
 The light À ashes if the vehicle is stopped but the brake pedal is not depressed with
suf¿ cient force. Depress the brake pedal a little more strongly because the pedal force
may be insuf¿ cient.

4–25
When Driving
Instrument Cluster and Display
*Some models.
Speedometer
The speedometer indicates the speed of the
vehicle.
NOTE
(Analog speedometer type)
If a few seconds have elapsed after
switching the ignition off, the needle
may deviate. However, this does not
indicate a problem.
Speed Unit Selector (Digital
Speedometer Type) *
In some countries, you may have to
change the speed units between km/h and
mph.
Press the speed unit selector for 1.5
seconds or more.
The speed units for the speedometer will
change between km/h and mph.


Speedometer
Speed unit selector

Odometer, Trip Meter and Trip
Meter Selector
The display mode can be changed from
odometer to trip meter A to trip meter B
and then back to odometer by pressing the
selector while one of them is displayed.
The selected mode will be displayed.


Press the selector Press the selector
Press the selector Odometer
Trip meter A
Trip meter BSelector


NOTE
When the ignition is switched to ACC
or off, the odometer or trip meters
cannot be displayed, however, pressing
the selector can inadvertently switch
the trip meters or reset them during an
approximate ten-minute period in the
following cases:
 
 After the ignition is switched to off
from ON.
  After the driver's door is opened.

4–26
When Driving
Instrument Cluster and Display
Odometer
The odometer records the total distance
the vehicle has been driven.
Trip meter
The trip meter can record the total distance
of two trips. One is recorded in trip meter
A, and the other is recorded in trip meter
B.

For instance, trip meter A can record the
distance from the point of origin, and
trip meter B can record the distance from
where the fuel tank is ¿ lled.

When trip meter A is selected, pressing
the selector again within one second will
change to trip meter B mode.

When trip meter A is selected, TRIP A
will be displayed. When trip meter B is
selected, TRIP B will be displayed.

The trip meter records the total distance
the vehicle is driven until the meter
is again reset. Return it to “0.0” by
depressing and holding the selector for
one second or more. Use this meter to
measure trip distances and to compute fuel
consumption. NOTE
  (Vehicles with type B audio)  If the fuel economy data is reset
using the fuel economy monitor,
or trip A is reset using the trip
meter when the function which
synchronizes the fuel economy
monitor and the trip meter is on, the
fuel economy data and trip A are
reset simultaneously.
 Refer to Fuel Economy Monitor on
page 4-91 .
  Only the trip meters record tenths of
kilometres (miles).
  The trip record will be erased when: 



 The power supply is interrupted
(blown fuse or the battery is
disconnected).
 


 The vehicle is driven over 9999.9
km (mile).

4–30
When Driving
Instrument Cluster and Display
*Some models.
Outside Temperature Warning *
When the outside temperature is low, the
indication À ashes and a beep sound is
heard to warn the driver of the possibility
of icy roads.
If the outside temperature is lower than
about 4 °C (39 °F), the outside temperature
display and the
mark À ashes for about
ten seconds and a beep sound is heard
once.
NOTE
If the outside temperature is lower than
-20 °C (-4 °F), the beep sound does not
operate. However, the
mark
illuminates.
Cruise Control Set Vehicle Speed
Display *
The vehicle speed preset using the cruise
control is displayed.



Adjustable Speed Limiter (ASL)
Display *
The setting status of the adjustable speed
limiter (ASL) is displayed.




Trip Computer and INFO Switch
The following information can be selected
by pressing the INFO switch with the
ignition switched ON.
 


 Distance-to-empty mode



 Average fuel economy mode



 Current fuel economy mode



 Average vehicle speed mode



 Vehicle speed alarm mode *
If you have any problems with your trip
computer, consult an expert repairer,
we recommend an Authorised Mazda
Repairer.
Distance-to-empty mode
This mode displays the approximate
distance you can travel on the remaining
fuel based on the fuel economy.

The distance-to-empty will be calculated
and displayed every second.
(European model)


(Except European model)