2017 MAZDA MODEL CX-3 fog light

4–106
When Driving
i-ACTIVSENSE
NOTE
The timing in which the system switches the headlights changes under the following
conditions. If the system does not switch the headlights appropriately, manually switch
between high and low beams according to the visibility as well as road and traf¿ c
conditions.
 
 When there are sources of light in the area such as street lamps, illuminated
signboards, and traf¿ c signals.

 When there are reÀ ective objects in the surrounding area such as reÀ ective plates and
signs.
  When visibility is reduced under rain, snow and foggy conditions. 
 When driving on roads with sharp turn or hilly terrain. 
 When the headlights/rear lamps of vehicles in front of you or in the opposite lane are
dim or not illuminated.
  When there is suf¿ cient darkness such as at dawn or dusk. 
 When the luggage compartment is loaded with heavy objects or the rear passenger
seats are occupied.
  When visibility is reduced due to a vehicle in front of you spraying water from its tyres
onto your windscreen.

4–110
When Driving
i-ACTIVSENSE
NOTE
Under the following conditions, the Adaptive LED Headlights (ALH) may not operate
normally. Manually switch between the high and low beams according to the visibility,
and the road and traf¿ c conditions.


 When there are other sources of light in the area such as street lamps, illuminated
signboards, and traf¿ c signals.

 When there are reÀ ective objects in the surrounding area such as reÀ ective plates and
signs.
  When visibility is reduced under rain, snow and foggy conditions. 
 When driving on roads with sharp curves or undulations. 
 When the headlights/rear lamps of vehicles ahead or in the opposite lane are dim or not
illuminated.
  When there is insuf¿ cient darkness such as at dawn or dusk. 
 When the luggage compartment is loaded with heavy objects or the rear passenger
seats are occupied.
  When visibility is reduced due to a vehicle ahead spraying water from its tyres onto
your windscreen.
To Operate the System
The system switches the headlights to the
high beams after the ignition is switched
ON and the headlight switch is in the

position. The Adaptive LED Headlights
(ALH) indicator light (green) in the
instrument cluster turns on simultaneously.


The Adaptive LED Headlights (ALH)
determine that it is nighttime based on the
brightness of the surrounding area.
The system cancels operation when the
headlight switch is turned to a position
other than
, the headlights are
manually switched to low beams, or the
high beams are À ashed on and off.
NOTE
The system can be changed so that the
Adaptive LED Headlights (ALH) do not
operate.
Refer to Personalisation Features on
page 9-13 .
Manual Switching
Switching to low beams
Shift the lever to the low beam position.
The Adaptive LED Headlights (ALH)
indicator light (green) turns off.
Switching to high beams
Turn the headlight switch to the

position.
The Adaptive LED Headlights (ALH)
indicator light (green) turns off and the

is illuminated.

4–111
When Driving
i-ACTIVSENSE
*Some models.
Lane Departure Warning System (LDWS) *
The LDWS system noti¿ es the driver that the vehicle may be deviating from its lane.
The system detects the white or yellow lines on the traf¿ c lane using the Forward Sensing
Camera (FSC) and if it determines that the vehicle may be deviating from its lane, it noti¿ es
the driver using the active driving display (vehicles with active driving display), and by
À ashing the LDWS warning light and activating the LDWS warning beep.
Use the LDWS when you drive the vehicle on roads with white or yellow lines.
Refer to Forward Sensing Camera on page 4-179 .


Forward Sensing Camera (FSC)

The warning light illuminates when the system has a malfunction.
Refer to Warning Lights on page 4-36 .
WARNING
Do not use the LDWS under the following conditions:
The system may not operate adequately according to the actual driving conditions,
resulting in an accident.
 
 Driving on roads with tight curves. 
 Driving under bad weather conditions (rain, fog, and snow).

The functions of the LDWS have limitations:
Always stay on course using the steering wheel and drive with care. The system is not
designed to compensate for a driver’s lack of caution and if you rely too much on the
LDWS it could lead to an accident. The driver is responsible for assuring lane changes
and other manoeuvres. Always pay attention to the direction in which the vehicle is
travelling and the vehicle’s surroundings.

4–113
When Driving
i-ACTIVSENSE
NOTE
  Under the following conditions, the LDWS may not be able to detect white or yellow
lines correctly and the LDWS may not operate correctly.
 


 If an object placed on the instrument panel is reÀ ected in the windscreen and picked
up by the camera.
 


 Heavy luggage is loaded in the luggage compartment or on the rear seat and the
vehicle is inclined.
 


 The tyre pressures are not adjusted to the speci¿ ed pressure.



 When the vehicle is driven on the entry and exit to or from the rest area or tollgate of
a highway.
 


 The white or yellow lines are less visible because of dirt or paint À aking.



 The vehicle ahead is running near a white or yellow line and the line is less visible.



 A white or yellow line is less visible because of bad weather (rain, fog, or snow).



 The vehicle is driven on a temporary lane or section with a closed lane due to
construction.
 


 A misleading line is picked up on the road such as a temporary line for construction,
or because of shade, lingering snow, or grooves ¿ lled with water.




 The surrounding brightness suddenly changes such as when entering or exiting a
tunnel.
 


 The illumination of the headlights is weakened because of dirt or the optical axis is
deviated.
 


 The windscreen is dirty or foggy.



 Back-light is reÀ ecting from the road surface.



 The road surface is wet and shiny after rain, or there are puddles on the road.



 The shade of a guardrail parallel to a white or yellow line is on the road.



 The width of a lane is excessively narrow or wide.



 The road is excessively uneven.



 The vehicle is shaken after hitting a road bump.



 There are two or more adjacent white or yellow lines.



 There are various road markings or lane markings of various shapes near an
intersection.

4–114
When Driving
i-ACTIVSENSE
When The System Operates
1. The system goes on operation standby
when the LDWS OFF switch is pressed
and the LDWS OFF indicator light
in the instrument cluster turns off.
For vehicles equipped with the active
driving display, the driving lane (border
lines) is indicated in the display.


2. Drive the vehicle in the centre of the
driving lane while the LDWS OFF
indicator light is turned off. The system
becomes operational when all of the
following conditions are met.
 

 
 The vehicle is driven in the centre
of the driving lane with the white
or yellow lines on the left and right
sides, or on either side.
 

 
 The vehicle speed is 70 km/h (44
mph) or faster.
 

 
 The vehicle is driven on a straight
road or road with gentle curves.

The LDWS does not operate in the
following cases:
 

 
 The system cannot detect white or
yellow lines.
 

 
 The vehicle speed is less than 65
km/h (40 mph).
 

 
 The vehicle is making a sharp turn.


 
 The vehicle is making a curve at an
inadequate speed.

NOTE
  The LDWS does not operate until the
system detects a white or yellow line
on either the left or right.
  When the system detects a white
or yellow line on one side only, the
system will activate the warning only
when the vehicle deviates on the side
where the white or yellow line is
being detected.
  The distance and warning sensitivity
(likelihood of a warning) which
the system uses to determine the
possibility of a lane departure can be
changed.
 Refer to Personalisation Features on
page 9-13 .
Auto cancel
In the following cases, the LDWS cancels
automatically and the LDWS warning
light in the instrument cluster turns on.
 


 The temperature inside the camera is
high or low.
 


 The windscreen around the camera is
foggy.
 


 The windscreen around the camera is
blocked by an obstruction, causing poor
forward visibility.

The LDWS is enabled automatically when
the operation conditions are met, and the
LDWS warning light turns off.

4–120
When Driving
i-ACTIVSENSE
NOTE
  The Blind Spot Monitoring (BSM) warning indicator light may turn on and the vehicle
detection screen may be displayed in the display in reaction to stationary objects
(guardrails, tunnels, sidewalls, and parked vehicles) on the road or the roadside.
Objects such as guardrails and concrete walls
running alongside the vehicle.Places where the width between guardrails or
walls on each side of the vehicle narrows.

The walls at the entrance and exits of tunnels,
turnouts.
  A Blind Spot Monitoring (BSM) warning indicator light may À ash or the warning beep
may be activated several times when making a turn at a city intersection.
  Turn off the Blind Spot Monitoring (BSM) while pulling a trailer or while an accessory
such as a bicycle carrier is installed to the rear of the vehicle. Otherwise, the radar’s
radio waves will be blocked causing the system to not operate normally.
  In the following cases, it may be dif¿ cult to view the illumination/À ashing of the Blind
Spot Monitoring (BSM) warning indicator lights equipped on the door mirrors.
 


 Snow or ice is adhering to the door mirrors.



 The front door glass is fogged or covered in snow, frost or dirt. 

 The system switches to the Rear Cross Traf¿ c Alert function when the shift lever
(manual transaxle) or the selector lever (automatic transaxle) is shifted to the reverse
(R) position.
 Refer to Rear Cross Traf¿ c Alert (RCTA) on page 4-137 .

4–122
When Driving
i-ACTIVSENSE
Function for cancelling illumination dimmer
If the Blind Spot Monitoring (BSM) warning indicator lights turn on when the position
lights are turned on, the brightness of the Blind Spot Monitoring (BSM) warning indicator
lights is dimmed.
If the Blind Spot Monitoring (BSM) warning indicator lights are dif¿ cult to see due to
glare from surrounding brightness when travelling on snow-covered roads or under foggy
conditions, press the dimmer cancellation button to cancel the dimmer and increase the
brightness of Blind Spot Monitoring (BSM) warning indicator lights when they turn on.
Refer to Instrument Panel Illumination on page 4-28 .
Display indicator (Vehicles with active driving display)
The detected approaching vehicle and warning are displayed in the active driving display
when the vehicle is moving forward (Blind Spot Monitoring (BSM) operational).


The detected direction is displayed with a detection indicator (white) when an approaching
vehicle is detected. In addition, if the direction indicator lever is operated to signal a lane
change while the vehicle is detected, the display changes the colour (amber) of the warning
indicator.
Blind Spot Monitoring (BSM) warning beep
The Blind Spot Monitoring (BSM) warning beep is activated simultaneously with the
À ashing of a Blind Spot Monitoring (BSM) warning indicator light.

4–126
When Driving
i-ACTIVSENSE
NOTE
  The Traf¿ c Sign Recognition System (TSR) does not operate if there is a malfunction
in the Forward Sensing Camera (FSC).
  Under the following conditions, the Traf¿ c Sign Recognition System (TSR) may not
operate normally.
 


 An object placed on the instrument panel is reÀ ected in the windscreen and picked
up by the camera.
 


 Heavy luggage is loaded in the luggage compartment or on the rear seat and the
vehicle is tilted.
 


 The tyre pressures are not adjusted to the speci¿ ed pressure.



 Tyres other than standard tyres are equipped.



 The vehicle is driven on the ramp and surrounding area to or from a rest area or a
tollgate on a highway.
 


 When surrounding brightness suddenly changes such as when entering or exiting a
tunnel.
 


 The illumination of the headlights is weakened because of dirt or the optical axis is
deviated.
 


 The windscreen is dirty or foggy.



 The windscreen and camera are fogged (water droplets).



 Strong light is directed at the front of the vehicle (such as backlight or high-beam
headlights of on-coming vehicles).
 


 The vehicle is making a sharp turn.



 Strong light reÀ ects off the road.



 A traf¿ c sign is in a position which makes it dif¿ cult to reÀ ect the light from the
vehicle's headlights, such as when the vehicle is driven at night or in a tunnel.
 


 The vehicle is driven under weather conditions such as rain, fog, or snow.



 The stored map data for the navigation system is not current.



 The camera cannot capture a traf¿ c sign's image.



 A traf¿ c sign is obscured by mud or snow.



 A traf¿ c sign is concealed by trees or a vehicle.



 A traf¿ c sign is partially shaded.



 A traf¿ c sign is bent or warped.



 A traf¿ c sign is too low or too high.



 A traf¿ c sign is too bright or too dark (including electronic traf¿ c signs).



 A traf¿ c sign is too big or too small.



 There is an object similar to the traf¿ c sign being read (such as another traf¿ c sign or
other signs resembling it).
 
 The Traf¿ c Sign Recognition System (TSR) does not operate if the active driving
display is set to non-display.
  The Traf¿ c Sign Recognition System (TSR) can be set to inoperable.  Refer to Personalisation Features on page 9-13 .