2017 MAZDA MODEL 6 parking brake

1–4
Pictorial Index
Interior Overview
Interior Equipment (View B)
SRS air bags ........................................................................\
.................................. page 2-40
Active driving display ........................................................................\
................... page 4-29
Climate control system ........................................................................\
.................... page 5-2
Rear window defogger switch ........................................................................\
....... page 4-63
Audio system ........................................................................\
................................. page 5-13
Glove compartment ........................................................................\
....................... page 5-92
Shift lever/Selector lever ........................................................................\
...... page 4-39, 4-42
Commander switch ........................................................................\
....................... page 5-21
Electric parking brake switch ........................................................................\
........ page 4-71
Drive selection switch ........................................................................\
................... page 4-86
Fuse block ........................................................................\
..................................... page 6-59
Storage pocket ........................................................................\
............................... page 5-91
The equipment and installation position varies by vehicle
Mazda6_8FH2-EA-16F_Edition2.indb 42016/07/07 13:44:08

2–9
Essential Safety Equipment
Seats
NOTE
 Individual seat positions can be
programmed to the two available
programming buttons on the side of the
driver's seat, plus one seat position for
each registered key.
 If the vehicle has been serviced and
the battery cables disconnected, the
programmed seat positions will have
been erased. Re-program the seat
positions.
Programming
1. Make sure the parking brake is on.
2. (Automatic transaxle)
Make sure the selector lever is in the P
position.
3. Start the engine.
4. Adjust the seat and the active driving
display to the desired driving position.
5. Press the SET button on the seat until a
beep sound is heard one time.
6. Perform one of the following settings
within 5 seconds of completing step 5
above:
 Programming using a button on
the side of the seat
Press the button you want to program,
either button 1 or 2, until a beep
sound is heard one time.
 Programming using the key
Press the key
button until a beep
sound is heard one time.
NOTE
If a beep sound is heard three times, the
operation is canceled.
To move the driving position to a
programmed position
(Using a button on the side of the seat)
1. Make sure the parking brake is on.
2. (Automatic transaxle)
Make sure the selector lever is in the P
position.
3. Start the engine.
4. Press the programming button for the
driving position you want to call up
(button 1 or 2).
5. A beep sound is heard when the driving
position adjustment is completed.
NOTE
 If the driving position movement is not
changed, only the beep sounds.
 A seat position can be called up even
with the engine not running.
 The driving position adjustment is
canceled in the following cases:
 Any of the seat adjustment switches
is operated.
 The SET button is pressed. Programming button 1 or 2 is
pressed.
 The key button or button is
operated.
 The vehicle starts moving. The active driving display is
adjusted.
Mazda6_8FH2-EA-16F_Edition2.indb 92016/07/07 13:44:11

2–10
Essential Safety Equipment
Seats
(Using a programmed key)
1. Unlock the doors by pressing a request
switch or the key
button.
2. After unlocking the doors, the seat
position adjustment begins within 40
seconds of opening the driver's door,
and a beep sounds when the operation
is finished.
3. Make sure the parking brake is on.
4. (Automatic transaxle)
Make sure the selector lever is in the P
position.
5. Start the engine.
6. The active driving display adjustment
begins.
NOTE
 If there is no driving position movement,
a beep is not heard.
 The driving position adjustment is
canceled in the following cases:
 Any of the seat adjustment switches
is operated.
 The SET button is pressed. Programming button 1 or 2 is
pressed.
 The key button or button is
operated.
 The vehicle starts moving. The active driving display is
adjusted.
Erasing programmed driving positions
(Erasing the driving positions
programmed to the key)
1. Switch the ignition OFF.
2. Press the SET button on the side of the
seat until a beep sound is heard one
time.
3. After the beep sounds, press the key

button within 5 seconds until a beep
sound is heard one time.
NOTE
If a beep sound is heard three times, the
operation is canceled.
Mazda6_8FH2-EA-16F_Edition2.indb 102016/07/07 13:44:11

4–4
When Driving
Start/Stop Engine
Ignition Switch
Push Button Start Positions
The system operates only when the key is
within operational range.
Each time the push button start is pressed,
the ignition switches in the order of off,
ACC, and ON. Pressing the push button
start again from ON switches the ignition
off.
Indicator light
Push b utton start
NOTE
 The engine starts by pressing the push
button start while depressing the clutch
pedal (manual transaxle) or the brake
pedal (automatic transaxle). To switch
the ignition position, press the push
button start without depressing the
pedal.
 Do not leave the ignition switched ON
while the engine is not running. Doing
so could result in the battery going
dead. If the ignition is left in ACC (For
automatic transaxle, the selector lever
is in the P position, and the ignition
is in ACC), the ignition switches off
automatically after about 25 minutes. Off
The power supply to electrical devices
turns off and the push button start indicator
light (amber) also turns off.
WARNING
Before leaving the driver's seat, always
switch the ignition off, set the parking
brake, and make sure the selector lever
is in P (automatic transaxle) or in 1st
gear or R (manual transaxle):
Leaving the driver's seat without
switching the ignition off, setting the
parking brake, and shifting the selector
lever to P (automatic transaxle) or
to 1st gear or R (manual transaxle)
is dangerous. Unexpected vehicle
movement could occur which could
result in an accident.
In addition, if your intention is to leave
the vehicle for even a short period, it
is important to switch the ignition off,
as leaving it in another position will
disable some of the vehicle's security
systems and run the battery down.
ACC (Accessory)
Some electrical accessories will operate
and the indicator light (amber) illuminates.
NOTE
The keyless entry system does not function
while the push button start has been
pressed to ACC, and the doors will not
lock/unlock even if they have been locked
manually.
Mazda6_8FH2-EA-16F_Edition2.indb 42016/07/07 13:44:32

4–6
When Driving
Start/Stop Engine
 Engine-starting is controlled by the
spark ignition system.
This system meets all Canadian
Interference-Causing Equipment
Standard requirements regulating the
impulse electrical field strength of radio
noise.
1. Make sure you are carrying the key.
2. Occupants should fasten their seat
belts.
3. Make sure the parking brake is on.
4. Continue to press the brake pedal
firmly until the engine has completely
started.
5. (Manual transaxle)
Continue to press the clutch pedal
firmly until the engine has completely
started.
(Automatic transaxle)
Put the vehicle in park (P). If you must
restart the engine while the vehicle is
moving, shift into neutral (N).
NOTE
(Manual transaxle)
The starter will not operate if the clutch
pedal is not depressed sufficiently.
(Automatic transaxle)
The starter will not operate if the selector
lever is not in P or N and the brake pedal
is not depressed sufficiently. 6.
Verify that the KEY indicator light
(green) (if equipped) in the instrument
cluster and the push button start
indicator light (green) illuminate.

Indicator light
Push b utton start
NOTE
 If the push button start indicator
light (green) flashes, make sure that
the key is being carried (for vehicles
with a type A instrument cluster (page
4-32), messages are displayed in the
instrument cluster).
 If the push button start indicator light
(green) flashes with the key being
carried, touch the key to the push button
start and start the engine (for vehicles
with a type A instrument cluster (page
4-32), messages are displayed in the
instrument cluster). Refer to Engine
Start Function When Key Battery is
Dead on page 4-8.
Mazda6_8FH2-EA-16F_Edition2.indb 62016/07/07 13:44:33

4–10
When Driving
Start/Stop Engine
Emergency Operation for Starting
the Engine
If the KEY warning light (red) illuminates,
or the push button start indicator light
(amber) flashes, this could indicate that
the engine may not start using the usual
starting method. Have your vehicle
inspected at an Authorized Mazda Dealer
as soon as possible. If this occurs, the
engine can be force-started. Press and hold
the push button start until the engine starts.
Other procedures necessary for starting the
engine such as having the key in the cabin,
and depressing the clutch pedal (manual
transaxle) or the brake pedal (automatic
transaxle) are required.
Turning the Engine Off
WARNING
Do not stop the engine while the vehicle
is moving:
Stopping the engine while the vehicle
is moving for any reason other than in
an emergency is dangerous. Stopping
the engine while the vehicle is moving
will result in reduced braking ability
due to the loss of power braking, which
could cause an accident and serious
injury.
1. Stop the vehicle completely.
2. (Manual transaxle)
Shift into neutral and set the parking
brake.
(Automatic transaxle)
Shift the selector lever to the P position
and set the parking brake.
3. Press the push button start to turn off
the engine. The ignition position is off.
CAUTION
When leaving the vehicle, make sure
the push button start is off.
Mazda6_8FH2-EA-16F_Edition2.indb 102016/07/07 13:44:33

4–33
When Driving
Instrument Cluster and Display
*Some models.
Warning Indication/Warning Lights
These lights turn on or flash to notify the user of the system operation status or a system
malfunction.
Signal WarningPage
Brake System Warning Light*1*27-22
ABS Warning Light*1
Electronic
Brake Force Distribution
System Warning 7-22,
ABS warning 7-25
Charging System Warning Light*17-22
Engine Oil Warning Light*17-22
(Red)
*High Engine Coolant Temperature Warning Indication/
Warning Light*17-22
Power Steering Malfunction Indication/Malfunction
Indicator Light*17-22
Master Warning Indication/Warning Light*17-25
Electric Parking Brake Warning Light 7-25
Check Engine Light*17-25
Automatic Transaxle Warning Indication/Warning Light*17-25
Air Bag/Front Seat Belt Pretensioner System Warning
Light*17-25
Tire Pressure Monitoring System Warning Light*1
Flashing
7-25,
Illuminate 7-29
(Amber)
*KEY Warning Indication 7-25
Mazda6_8FH2-EA-16F_Edition2.indb 332016/07/07 13:44:44

4–35
When Driving
Instrument Cluster and Display
*Some models.
SignalWarningPage
*Door-Ajar Warning Indication 7-29
*Trunk lid-Ajar Warning Indication7-29
*Door-Ajar Warning Light7-29
*1 The light turns on when the ignition is switched on for an operation che\
ck, and turns off a few seconds later or
when the engine is started. If the light does not turn on or remains tur\
ned on, have the vehicle inspected at an
Authorized Mazda Dealer.
*2 The light turns on continuously when the parking brake is applied.
Mazda6_8FH2-EA-16F_Edition2.indb 352016/07/07 13:44:46