2017 MAZDA MODEL 2 headlights

4–71
When Driving
Switches and Controls
Type B (Without Front Fog Light)
The headlights must be turned on to turn
on the rear fog light.

To turn the rear fog light on, rotate the fog
light switch to the
position (the fog
light switch returns to its original position
automatically).
The rear fog light indicator light in the
instrument cluster illuminates while the
rear fog light is on.


Fog light switch
To turn the rear fog light off, do any of the
following:
 


 Rotate the fog light switch to the
position again (the fog light switch
returns to its original position
automatically).
 


 Turn the headlight switch to the
position.

The rear fog light indicator light in the
instrument cluster goes off when the rear
fog light is turned off.
NOTE
(With auto-light control)
When the headlight switch is in the

position and the headlights, exterior
lights and instrument panel illuminated,
the rear fog light turns on when the rear
fog light switch is turned on.
Turn and Lane-Change
Signals
The ignition must be switched ON to use
the turn and lane-change signals.
Direction Indicators
Move the signal lever down (for a left
turn) or up (for a right turn) to the stop
position. The signal will self-cancel after
the turn is completed.

If the indicator light continues to À ash
after a turn, manually return the lever to its
original position.

Right turn
Left turn Right lane change
Left lane changeOFF

The direction indicators in the instrument
cluster À ash according to the operation of
the direction indicator lever to show which
signal is working.

4–76
When Driving
Switches and Controls
NOTE
  If the auto-wiper lever is left in the

position, the wipers could
operate automatically from the effect
of strong light sources,
electromagnetic waves, or infrared
light because the rain sensor uses an
optical sensor. It is recommended
that the auto-wiper lever be switched
to the
position other than when
driving the vehicle under rainy
conditions.
  The auto-wiper control functions can
be turned off.
 Refer to Personalisation Features on
page 9-13 .
Windscreen Washer
Pull the lever toward you and hold it to
spray washer À uid.


Washer OFF

NOTE
If the windscreen washer is turned
on when the windscreen wipers are
not operating, the windscreen wipers
operate a few times.
If the washer does not work, inspect the
À uid level (page 6-32 ). If the À uid level
is normal, consult an expert repairer,
we recommend an Authorised Mazda
Repairer.
NOTE
(With headlight washers)
When the headlights are on, the
headlight washers operate automatically
once every ¿ fth time the windscreen
washer operates.
Refer to Headlight Washer on page
4-77 .

4–77
When Driving
Switches and Controls
*Some models.
Rear Window Wiper and
Washer
*
The ignition must be switched ON to use
the wiper.
Rear Window Wiper

Turn the wiper on by turning the rear
wiper/washer switch.

Switch Position
Wiper operation
No. Type A Type B

Stop

Intermittent

Normal

Rear Window Washer
T o s p r a y w a s h e r À uid, turn the rear wiper/
washer switch to either of the
position.
After the switch is released, the washer
will stop.
If the washer does not work, inspect the
À uid level (page 6-32 ). If the À uid
level is normal and the washer still does
not work, consult an expert repairer,
we recommend an Authorised Mazda
Repairer.
Headlight Washer *
The engine must be started and the
headlights must be turned on.

If you want to operate headlight washers,
double À ick the wiper lever.


Washer OFF

NOTE
  When the windscreen washer
is operated for the ¿ rst time
after turning on the headlights,
the headlight washers operate
automatically.
  If air enters the headlight washer
À uid pipe under conditions such
as when the vehicle is brand-new
or after an empty washer tank is
replenished with washer À uid,
washer À uid will not spray even
when the wiper lever is operated. If
this occurs, perform the following
procedure:

1. Start the engine.
2. Turn on the headlights.
3. Double À ick the wiper lever
several times until the washer
À uid sprays.

4–102
When Driving
i-ACTIVSENSE
*Some models.
i-ACTIVSENSE *
i-ACTIVSENSE is a collective term covering a series of advanced safety and driver support
systems which make use of a Forward Sensing Camera (FSC) and radar sensors. These
systems consist of active safety and pre-crash safety systems.
These systems are designed to assist the driver in safer driving by reducing the load on the
driver and helping to avert collisions or reduce their severity. However, because each system
has its limitations, always drive carefully and do not rely solely on the systems.
Active Safety Technology
Active Safety Technology supports safer driving by helping the driver to recognise potential
hazards and avert accidents.
Driver awareness support systems
Nighttime visibility
Adaptive LED Headlights (ALH) ..................................................................................... 4-108
High Beam Control System (HBC) .................................................................................. 4-105
Left/right side and rear side detection
Lane Departure Warning System (LDWS) ....................................................................... 4-111
Blind Spot Monitoring (BSM) .......................................................................................... 4-117
Inter-vehicle distance recognition
Distance Recognition Support System (DRSS) ................................................................ 4-124
Driver fatigue detection
Driver Attention Alert (DAA) ........................................................................................... 4-127
Rear obstruction detection when leaving a parking space
Rear Cross Traf¿ c Alert (RCTA) ...................................................................................... 4-130
Driver support systems
Inter-vehicle distance
Mazda Radar Cruise Control (MRCC) ............................................................................. 4-135
Speed control
Adjustable Speed Limiter ................................................................................................. 4-148

4–103
When Driving
i-ACTIVSENSE
Pre-Crash Safety Technology
Pre-crash safety technology is designed to assist the driver in averting collisions or reduce
their severity in situations where they cannot be avoided.
Collision damage reduction in low vehicle speed range
Forward driving
Smart City Brake Support [Forward] (SCBS F) ............................................................... 4-155
Reverse driving
Smart City Brake Support [Reverse] (SCBS R) ............................................................... 4-161
Collision damage reduction in medium/high speed range
Smart Brake Support (SBS) .............................................................................................. 4-167
Camera and Sensors
Forward Sensing Camera (FSC)
The Forward Sensing Camera (FSC) detects lane indications and recognises headlights, tail
lights and city lights during nighttime driving. The following systems also use the Forward
Sensing Camera (FSC).
 


 High Beam Control System (HBC)



 Adaptive LED Headlights (ALH)



 Driver Attention Alert (DAA)



 Lane Departure Warning System (LDWS)



 Smart Brake Support (SBS)
The Forward Sensing Camera (FSC) is installed at the top of the windscreen near the
rearview mirror.
Refer to Forward Sensing Camera (FSC) on page 4-170 .
Radar sensor (front)
The radar sensor (front) functions by detecting the radio waves reÀ ected off a vehicle ahead
sent from the radar sensor. The following systems also use the radar sensor (front).
 


 Distance Recognition Support System (DRSS)



 Mazda Radar Cruise Control (MRCC)



 Smart Brake Support (SBS)
The radar sensor (front) is mounted behind the radiator grille.
Refer to Radar Sensor (Front) on page 4-176 .

4–105
When Driving
i-ACTIVSENSE
*Some models.
High Beam Control System (HBC) *
The High Beam Control System (HBC) determines the conditions in front of the vehicle
using the Forward Sensing Camera (FSC) while driving in darkness to automatically switch
the headlights between high and low beams.
Refer to Warning/Indicator Lights on page 4-38 .
While driving the vehicle at a speed of about 30 km/h (19 mph) or more, the headlights are
switched to high beams when there are no vehicles ahead or approaching in the opposite
direction.
The system switches the headlights to low beams when one of the following occurs:
 


 The system detects a vehicle or the headlights/lights of a vehicle approaching in the
opposite direction.
 


 The vehicle is driven on roads lined with streetlamps or on roads in well-lit cities and
towns.
 


 The vehicle is driven at less than about 20 km/h (12 mph).

Forward Sensing
Camera (FSC) The recognition distance of the
Forward Sensing Camera (FSC)
varies according to the
surrounding conditions.

The warning light À ashes when the system has a malfunction.
Refer to Warning Lights on page 4-38 .
CAUTION
  Do not adjust the vehicle height, modify the headlight units, or remove the camera,
otherwise the system will not operate normally.
  Do not rely excessively on the High Beam Control System (HBC) and drive the
vehicle while paying suf¿ cient attention to safety. Switch the headlights between the
high beams and low beams manually if necessary.

4–106
When Driving
i-ACTIVSENSE
NOTE
The timing in which the system switches the headlights changes under the following
conditions. If the system does not switch the headlights appropriately, manually switch
between high and low beams according to the visibility as well as road and traf¿ c
conditions.
 
 When there are sources of light in the area such as street lamps, illuminated
signboards, and traf¿ c signals.

 When there are reÀ ective objects in the surrounding area such as reÀ ective plates and
signs.
  When visibility is reduced under rain, snow and foggy conditions. 
 When driving on roads with sharp turn or hilly terrain. 
 When the headlights/rear lamps of vehicles in front of you or in the opposite lane are
dim or not illuminated.
  When there is suf¿ cient darkness such as at dawn or dusk. 
 When the luggage compartment is loaded with heavy objects or the rear passenger
seats are occupied.
  When visibility is reduced due to a vehicle in front of you spraying water from its tyres
onto your windscreen.
To Operate the System
The High Beam Control System (HBC)
operates to switch the headlights
automatically between high and low
beams after the ignition is switched ON
and the headlight switch is in the AUTO
and high beam position.
The High Beam Control System (HBC)
determines that it is dark based on the
brightness of the surrounding area. At the
same time, the High Beam Control System
(HBC) indicator light (green) in the
instrument cluster illuminates.



NOTE
  When the vehicle speed is about
30 km/h (19 mph) or more, the
headlights automatically switch
to high beams when there are no
vehicles ahead or approaching in the
opposite direction.
 When the vehicle speed is less
than about 20 km/h (12 mph), the
High Beam Control System (HBC)
switches the headlights to low
beams.
  The low beams may not switch to
high beams when cornering.
  Operation of the High Beam Control
System (HBC) function can be
disabled. Refer to Personalisation
Features on page 9-13 .

4–10 8
When Driving
i-ACTIVSENSE
*Some models.
Adaptive LED Headlights (ALH) *
The Adaptive LED Headlights (ALH) are a system which uses the Forward Sensing Camera
(FSC) to determine the situation of a vehicle ahead or a vehicle approaching in the opposite
direction while driving at night to automatically switch the illumination range of the
headlights, the illuminated area, or the illumination brightness.
Refer to Forward Sensing Camera (FSC) on page 4-170 .
The Adaptive LED Headlights (ALH) are controlled between high and low beams as follows
to assure the driver’s visibility without dazzling a vehicle ahead or a vehicle approaching in
the opposite direction.
Glare-Free High Beam
This feature dims only the high-beam light shone on the vehicle ahead.
The high beams will dim while driving at a speed of about 40 km/h (25 mph) or faster.
When the vehicle speed is less than about 30 km/h (18 mph), the beams switch to the low
beams.


NOTE
The headlight high-beam indicator light turns on while the high beams are on.