2017 MAZDA MODEL 2 fog light

4–110
When Driving
i-ACTIVSENSE
NOTE
Under the following conditions, the Adaptive LED Headlights (ALH) may not operate
normally. Manually switch between the high and low beams according to the visibility,
and the road and traf¿ c conditions.


 When there are other sources of light in the area such as street lamps, illuminated
signboards, and traf¿ c signals.

 When there are reÀ ective objects in the surrounding area such as reÀ ective plates and
signs.
  When visibility is reduced under rain, snow and foggy conditions. 
 When driving on roads with sharp curves or undulations. 
 When the headlights/rear lamps of vehicles ahead or in the opposite lane are dim or not
illuminated.
  When there is insuf¿ cient darkness such as at dawn or dusk. 
 When the luggage compartment is loaded with heavy objects or the rear passenger
seats are occupied.
  When visibility is reduced due to a vehicle ahead spraying water from its tyres onto
your windscreen.
To Operate the System
The system switches the headlights to the
high beams after the ignition is switched
ON and the headlight switch is in the

position. The Adaptive LED Headlights
(ALH) indicator light (green) in the
instrument cluster turns on simultaneously.


The Adaptive LED Headlights (ALH)
determine that it is nighttime based on the
brightness of the surrounding area.
The system cancels operation when the
headlight switch is turned to a position
other than
, the headlights are
manually switched to low beams, or the
high beams are À ashed on and off.
NOTE
The system can be changed so that the
Adaptive LED Headlights (ALH) do not
operate.
Refer to Personalisation Features on
page 9-13 .
Manual Switching
Switching to low beams
Shift the lever to the low beam position.
The Adaptive LED Headlights (ALH)
indicator light (green) turns off.
Switching to high beams
Turn the headlight switch to the

position.
The Adaptive LED Headlights (ALH)
indicator light (green) turns off and the

is illuminated.

4–111
When Driving
i-ACTIVSENSE
*Some models.
Lane Departure Warning System (LDWS) *
The LDWS system noti¿ es the driver that the vehicle may be deviating from its lane.
The system detects the white or yellow lines on the traf¿ c lane using the Forward Sensing
Camera (FSC) and if it determines that the vehicle may be deviating from its lane, it noti¿ es
the driver using the active driving display (vehicles with active driving display), and by
À ashing the LDWS warning light and activating the LDWS warning beep.
Use the LDWS when you drive the vehicle on roads with white or yellow lines.
Refer to Forward Sensing Camera on page 4-170 .


Forward Sensing Camera (FSC)

The warning light illuminates when the system has a malfunction.
Refer to Warning Lights on page 4-38 .
WARNING
Do not use the LDWS under the following conditions:
The system may not operate adequately according to the actual driving conditions,
resulting in an accident.
 
 Driving on roads with tight curves. 
 Driving under bad weather conditions (rain, fog, and snow).

The functions of the LDWS have limitations:
Always stay on course using the steering wheel and drive with care. The system is not
designed to compensate for a driver’s lack of caution and if you rely too much on the
LDWS it could lead to an accident. The driver is responsible for assuring lane changes
and other manoeuvres. Always pay attention to the direction in which the vehicle is
travelling and the vehicle’s surroundings.

4–113
When Driving
i-ACTIVSENSE
NOTE
  Under the following conditions, the LDWS may not be able to detect white or yellow
lines correctly and the LDWS may not operate correctly.
 


 If an object placed on the instrument panel is reÀ ected in the windscreen and picked
up by the camera.
 


 Heavy luggage is loaded in the luggage compartment or on the rear seat and the
vehicle is inclined.
 


 The tyre pressures are not adjusted to the speci¿ ed pressure.



 When the vehicle is driven on the entry and exit to or from the rest area or tollgate of
a highway.
 


 The white or yellow lines are less visible because of dirt or paint À aking.



 The vehicle ahead is running near a white or yellow line and the line is less visible.



 A white or yellow line is less visible because of bad weather (rain, fog, or snow).



 The vehicle is driven on a temporary lane or section with a closed lane due to
construction.
 


 A misleading line is picked up on the road such as a temporary line for construction,
or because of shade, lingering snow, or grooves ¿ lled with water.




 The surrounding brightness suddenly changes such as when entering or exiting a
tunnel.
 


 The illumination of the headlights is weakened because of dirt or the optical axis is
deviated.
 


 The windscreen is dirty or foggy.



 Back-light is reÀ ecting from the road surface.



 The road surface is wet and shiny after rain, or there are puddles on the road.



 The shade of a guardrail parallel to a white or yellow line is on the road.



 The width of a lane is excessively narrow or wide.



 The road is excessively uneven.



 The vehicle is shaken after hitting a road bump.



 There are two or more adjacent white or yellow lines.



 There are various road markings or lane markings of various shapes near an
intersection.

4–114
When Driving
i-ACTIVSENSE
When The System Operates
1. The system goes on operation standby
when the LDWS OFF switch is pressed
and the LDWS OFF indicator light in
the instrument cluster turns off.


2. Drive the vehicle in the centre of the
driving lane while the LDWS OFF
indicator light is turned off. The system
becomes operational when all of the
following conditions are met.
 

 
 The vehicle is driven in the centre
of the driving lane with the white
or yellow lines on the left and right
sides, or on either side.
 

 
 The vehicle speed is 70 km/h
(44 mph) or faster.
 

 
 The vehicle is driven on a straight
road or road with gentle curves.

The LDWS does not operate in the
following cases:
 

 
 The system cannot detect white or
yellow lines.
 

 
 The vehicle speed is less than
65 km/h (40 mph).
 

 
 The vehicle is making a sharp turn.


 
 The vehicle is making a curve at an
inadequate speed.

NOTE
  The LDWS does not operate until the
system detects a white or yellow line
on either the left or right.
  When the system detects a white
or yellow line on one side only, the
system will activate the warning only
when the vehicle deviates on the side
where the white or yellow line is
being detected.
  The distance and warning sensitivity
(likelihood of a warning) which
the system uses to determine the
possibility of a lane departure can be
changed.
 Refer to Personalisation Features on
page 9-13 .
Auto cancel
In the following cases, the LDWS cancels
automatically and the LDWS warning
light in the instrument cluster turns on.
 


 The temperature inside the camera is
high or low.
 


 The windscreen around the camera is
foggy.
 


 The windscreen around the camera is
blocked by an obstruction, causing poor
forward visibility.

The LDWS is enabled automatically when
the operation conditions are met, and the
LDWS warning light turns off.

4–120
When Driving
i-ACTIVSENSE
NOTE
  The Blind Spot Monitoring (BSM) warning indicator light may turn on and the vehicle
detection screen may be displayed in the display in reaction to stationary objects
(guardrails, tunnels, sidewalls, and parked vehicles) on the road or the roadside.
Objects such as guardrails and concrete walls
running alongside the vehicle.Places where the width between guardrails or
walls on each side of the vehicle narrows.

The walls at the entrance and exits of tunnels,
turnouts.
  A Blind Spot Monitoring (BSM) warning indicator light may À ash or the warning beep
may be activated several times when making a turn at a city intersection.
  Turn off the Blind Spot Monitoring (BSM) while pulling a trailer or while an accessory
such as a bicycle carrier is installed to the rear of the vehicle. Otherwise, the radar’s
radio waves will be blocked causing the system to not operate normally.
  In the following cases, it may be dif¿ cult to view the illumination/À ashing of the Blind
Spot Monitoring (BSM) warning indicator lights equipped on the door mirrors.
 


 Snow or ice is adhering to the door mirrors.



 The front door glass is fogged or covered in snow, frost or dirt. 

 The system switches to the Rear Cross Traf¿ c Alert function when the shift lever
(manual transaxle) or the selector lever (automatic transaxle) is shifted to the reverse
(R) position.
 Refer to Rear Cross Traf¿ c Alert (RCTA) on page 4-130 .

4–122
When Driving
i-ACTIVSENSE
Function for cancelling illumination dimmer
If the Blind Spot Monitoring (BSM) warning indicator lights turn on when the position
lights are turned on, the brightness of the Blind Spot Monitoring (BSM) warning indicator
lights is dimmed.
If the Blind Spot Monitoring (BSM) warning indicator lights are dif¿ cult to see due to
glare from surrounding brightness when travelling on snow-covered roads or under foggy
conditions, press the dimmer cancellation button to cancel the dimmer and increase the
brightness of Blind Spot Monitoring (BSM) warning indicator lights when they turn on.
Refer to Instrument Panel Illumination on page 4-30 .
Display indicator (Vehicles with active driving display)
The detected approaching vehicle and warning are displayed in the active driving display
when the vehicle is moving forward (Blind Spot Monitoring (BSM) operational).


The detected direction is displayed with a detection indicator (white) when an approaching
vehicle is detected. In addition, if the direction indicator lever is operated to signal a lane
change while the vehicle is detected, the display changes the colour (amber) of the warning
indicator.
Blind Spot Monitoring (BSM) warning beep
The Blind Spot Monitoring (BSM) warning beep is activated simultaneously with the
À ashing of a Blind Spot Monitoring (BSM) warning indicator light.

4–134
When Driving
i-ACTIVSENSE
NOTE
  In the following cases, it may be dif¿ cult to view the illumination/À ashing of the Blind
Spot Monitoring (BSM) warning indicator lights equipped on the door mirrors.
 


 Snow or ice adheres to the door mirrors.



 The front door glass is fogged or covered in snow, frost or dirt. 

 Turn off the Rear Cross Traf¿ c Alert (RCTA) system while pulling a trailer or while
an accessory such as a bicycle carrier is installed to the rear of the vehicle. Otherwise,
the radio waves emitted by the radar will be blocked causing the system to not operate
normally.

4–158
When Driving
i-ACTIVSENSE
NOTE
  The Smart City Brake Support (SCBS) system will not operate if the driver is
deliberately performing driving operations (accelerator pedal and steering wheel).
  The Smart City Brake Support (SCBS) system will operate under the following
conditions.
 


 The engine is running.



 The Smart City Brake Support (SCBS) warning light (amber) does not illuminate.



 The vehicle speed is between about 4 to 30 km/h (2 to 18 mph).



 The Smart City Brake Support (SCBS) system is not turned off.



 The DSC is not malfunctioning. 

 The Smart City Brake Support (SCBS) detects a vehicle ahead by emitting a near-
infrared laser beam and receiving the beam reÀ ected off the reÀ ector of the vehicle
ahead, and then using it for the measurement. Consequently, the Smart City Brake
Support (SCBS) may not operate under the following conditions:
 


 ReÀ ection of the laser is poor due to the shape of the vehicle ahead.



 The vehicle ahead is signi¿ cantly dirty.



 Under bad weather condition, such as rain, fog and snow.



 The window washer is being used or the windscreen wipers are not used when it's
raining.
 


 The windscreen is dirty.



 The steering wheel is turned completely left or right, or the vehicle is accelerated
rapidly and comes close to the vehicle ahead.
 


 Trucks with low loading platforms and vehicles with an extremely low or high
pro¿ le.




 Vehicles with certain shapes such as a vehicle carrier. 

 Under the following conditions, the Smart City Brake Support (SCBS) system may not
operate normally.
 


 Heavy luggage is loaded in the luggage compartment or on the rear seat.



 If there is the possibility of partial contact with a vehicle ahead.



 When driving on continuously curving roads, and entering and exiting exits.



 Elongated luggage or cargo is loaded onto installed roof rails and covers the laser
sensor.
 


 Exhaust gas from the vehicle in front, sand, snow, and water vapour rising from
manholes and grating, and water splashed into the air.
 


 When towing a malfunctioning vehicle.



 When driving with tyres having signi¿ cantly different wear.