2017 KIA SPORTAGE sensor

9ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPERATING INFORMATION AND SAFETY WARNINGS. *IF EQUIPPED
DRIVER'S PANEL
Blind Spot Detection (BSD) System*
The BSD system uses radar sensors to help alert the driver before changing lanes. The
light on the BSD button A will illuminate when turned ON. The outside rearview mirror
warning lights will also illuminate for 3 seconds.
The system will become active when the vehicle is traveling more than 20 mph and will
alert the driver if another vehicle is detected by the radar sensor, up to 230 feet away.
For more information on the Blind Spot Detection System, please refer to the Owner’s Manual.
Blind Spot Detection*/Lane Change Assist*
1st-stage alert: When another vehicle is detected within the BSD system boundary B, a
yellow indicator will illuminate on the outside rearview mirrors.
2nd-stage alert: When 1st-stage alert is on and the driver activates a turn signal, a
flashing yellow indicator will illuminate on the outside rearview mirrors and the system
will sound an alert.
Rear Cross Traffic Alert (RCTA)*
If the RCTA system sensors detect approaching vehicles from the left or right side C, the
system will sound an audible alert, the warning indicators on the outside rearview mirror
will illuminate and a message will appear on the LCD screen, with these conditions:
•When the gear shift is in Reverse
•When the vehicle moves in reverse from a parked position
•When the vehicle is moving less than 6 mph
REMINDERS:
•When the BSD system is ON and the ignition is cycled to OFF then ON again, the BSD system returns to ON
•The RCTA feature can be turned OFF/ON in User Settings
Blind Spot Detection System Video To view a video on your mobile device, snap this QR Code or visit the listed website.
Refer to page 2 for more information.
www.KuTechVideos.com/ql13/2017
QR CODE
A
B
C

SPORTAGE FEATURES & FUNCTIONS GUIDE10*IF EQUIPPED
DRIVER'S PANEL
Lane Departure Warning System (LDWS)*
With the ENGINE START/STOP button in the ON position, press
the LDWS button C to turn system ON. The instrument cluster
indicator will illuminate green.
If the LDWS detects that you are veering outside of your lane, the
system may issue a warning on the LCD screen and an alert may
sound, under these conditions:
•The vehicle exceeds approximately 43 mph
•The LDWS system recognizes the lane the vehicle is traveling in
REMINDERS:
•LDWS will not issue a warning if the turn signal is activated
• If the LDWS button is ON and ignition is cycled, the system will turn ON again. If the LDWS button is OFF, the system remains OFF
Instrument Panel Dimmer
With parking lights/headlights ON, toggle switch A up (+) or down (-) to adjust the brightness of
the instrument panel illumination.
REMINDER: The Instrument Panel Dimmer does not adjust brightness on the audio/navigation system* screens; use SETUP to adjust brightness on the screens.
A
B
C
(Buttons located on left of Steering Wheel)Lane Departure
Lane Departure
Lane Departure
Lane Departure
Lane Departure Warning System Video
To view a video on your mobile device, snap this QR Code or visit the listed website.
Refer to page 2 for more information.
www.KuTechVideos.com/ql13/2017
QR CODE
The Lane Departure Warning System (LDWS) is not a substitute for safe and proper driving. Always drive safely and use caution. LDWS may not always alert the driver if the vehicle is driven outside of its lane.
When the LDWS sensor detects the lane traveling inWhen the LDWS sensor does not detect the lane traveling in
When the LDWS sensor detects the vehicle veering outside of the lane traveling in, a yellow indicator will illuminate
Electronic Stability Control (ESC)
The ESC system is designed to help stabilize the
vehicle during cornering maneuvers. It is a good
idea to keep the ESC turned ON for daily driving
whenever possible.
Press ESC button B to turn ESC OFF/ON.
REMINDERS:
•ESC is turned ON by default at vehicle start-up. When ignition is cycled, ESC will turn ON again
• The ESC Indicator Light in the instrument cluster will illuminate whenever the ESC is in operation

SPORTAGE FEATURES & FUNCTIONS GUIDE34*IF EQUIPPED
OTHER KEY FEATURES
How to Sync Transmitter with HomeLink®*
If programming for the first time, begin with Step 1 (repeating this step will
delete all information).
To program non-rolling and rolling code garage door openers and other devices:
1. Press and hold the left A and center D buttons simultaneously until the
indicator light C begins to flash (to reprogram buttons, skip this step)
2. Press and hold the desired button A, B or D and hold the button on the
transmitter while it is approximately 1 to 3 inches away from the mirror. The
HomeLink® Indicator light C will flash rapidly once the frequency signal has
been successfully programmed
To finish programming rolling code garage door openers, complete these steps:
3. Locate the “learn” or “smart” button on the garage door’s motor head unit.
Press and release the button and complete Step 4 within 30 seconds
4. Firmly press and release the programmed HomeLink® button up to three times
Operating HomeLink®:
Press one of the programmed HomeLink® buttons.
Erasing programmed buttons:
Press and hold the left A and center D buttons simultaneously for
approximately 20 seconds, and then release both buttons within 30 seconds.
REMINDER: Mirror indicator light C will illuminate when automatic dimming is ON.
The HomeLink® / Auto-Dimming Rearview Mirror* is designed to
reduce glare from a vehicle’s headlights located in the rear and also
connect up to three electronic transmitters into one location.
• To turn automatic dimming ON, press button F
• To turn automatic dimming OFF, press button G
HomeLink® with Auto-Dimming
Rearview Mirror*
A HomeLink® button
B HomeLink® button
C Indicator light
D HomeLink® button
E Glare detection sensor
F Automatic dimming ON
G Automatic dimming OFF
ABCDEFG

•You can reprogram a single HomeLink® button by repeating Step 2 •Erasing programmed buttons will delete all trained transmitters
QUICK TIPS
If your garage door opener was manufactured in 2011 or later, and you’re unable to program your vehicle’s HomeLink® system, you may need to purchase a HomeLink Repeater Kit. For more information, go to www.HomeLink.com or call (800) 355-3515.