2017 KIA K900 buttons

36
Power Reclining Rear Seats*
The rear seats can be adjusted by using the control switches
located on the door.
Seatback & Seat Slide Adjustment:
§
Move the button C forward/backward to adjust the
seatback position
§
Move the button D forward/backward to adjust the
seat position
Easy Access (AUTO) Button – When opening the rear door, the
rear seats will automatically move rearward to provide
easier access for passengers. Press the AUTO button
E on
the door panel to turn the system ON (LED is lit) and OFF (LED
not lit).
REMINDERS:
- Keep hands and other objects away from seat
mechanisms while the seat is in motion
- Do not adjust the seat while wearing seat belts
- Do not operate the rear power seat while the child
seat is installed
- Do not operate two or more power seat control
switches at the same time. Doing so may result
in power seat motor or electrical component
malfunction
C
D
E
(Controls located on door panel)
The integrated system stores into memory the position of
the driver’s seat, outside rearview mirrors, Head-Up Display
(HUD)*, and steering wheel positions. To store positions into
memory, first place the gear shift into P (Park) while the
ENGINE START/STOP button is in the ON position. Then:
1. Adjust the driver’s seat, outside rearview mirrors, Head-
Up Display (HUD)* settings and steering wheel positions
2. Press the SET button A on the control panel. System will
beep once
3. Press one of the memory buttons 1 or 2 B within 5
seconds. The system will beep twice when memory has
been stored
Driver Position Memory System
(Buttons located on driver door panel)
B
A
S E AT I N G
*IF EQUIPPED
S E AT I N G
*IF EQUIPPED

37
Rear Passenger’s Control System
The rear passenger’s control system lets users adjust the rear
and front seat controls, rear audio control and climate control.
Rear Seat Adjustment
To activate or deactivate the system, press the RE AR LOCK
button
A on the rear armrest console.
To control the rear seat lumbar support*, press the L (left
seat)
B or R (right seat) C button.
To adjust the lumbar support, move the lever
D:
§ To the LEFT to increase
§ To the RIGHT to decrease
§
UP to move the support position higher
§ DOWN to move lower
Quick Tip
Users can also activate/deactivate the rear passenger control system through the navigation
system. Press the CLIMATE button on the center
panel and deselect the Rear Climate option. If
the rear climate controls have been deactivated
through navigation system, they must be activated
the same way.
DF
E
G
C
B
A
Front Passenger Seat Adjustment
To adjust the angle of the front passenger’s seat from the
rear seat control system or the buttons on front seatback,
press the top/bottom of button
F to angle the front
seatback forward/backward.
To adjust the position of front passenger’s seat from
the rear seat control system or the buttons on the front
seatback, press the top/bottom of button
G to move the
seat forward/backward.
REMINDER: The front passenger seat adjustments F G only operate when seat is not occupied.
Easy Access (AUTO) – When opening the rear door, the rear seats will automatically move rearward to
provide easier access for passengers.
Press the AUTO button
E on the door panel to turn the system ON (LED is lit) or OFF (LED not lit).
(Buttons located on left side of
front passenger seatback)
F
G
S E AT I N G
*IF EQUIPPED
ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLE TE OPER ATING INFORMATION AND SAFE T Y WARNINGS.

39
P o w e r Tr u n k
The Power Trunk can be operated from several controls to
either open, close or lock the trunk. The Power Trunk Lock
button will close the trunk, lock all doors and trunk and then
arm the vehicle.
To turn the Power Trunk features ON, press the Power Trunk
Lid Control button to ON, located inside the glove box.
Driver’s Panel Power Trunk Main Control Lever – Located
to the left of the steering wheel, below the main button panel.
To open, pull the Power Trunk Main Control lever
A.
To close, press and hold the Power Trunk Main Control lever
A.
Power Trunk Close/Lock Buttons – Located underneath
the inside of the trunk lid.
To close trunk – Press the Trunk Close button
B.
To close trunk and lock and arm all doors/trunk, press the
Trunk Lock button
C.
Exterior Power Trunk Open Button – Located underneath
the outside of the trunk lid. To open, press the soft-touch
Power Trunk Open button.
Quick Tips
- The trunk must be unlocked before it can be
opened by the Trunk Release button
- The trunk unlocks automatically and then can be
opened manually when the Smart Key is within
close proximity to the vehicle
BC
www.KuTechVideos.com/kh13/2017
POWER TRUNK VIDEO
To view a video on your
mobile device, snap
this QR Code or visit the
listed website. Refer
to page 2 for more
information.
A
(Button located under driver’s
panel, left of the steering wheel)
REMINDERS:
- Power Trunk may be damaged if attempting to
open or close manually
- When not in use, keep the Trunk Lid Control
button in the OFF position
- If going through a car wash, remind the attendant
to keep the vehicle in Neutral (N) and keep the
engine running. Also, disable the Power Trunk
lid control using the button inside the glove
compartment, turn off the auto rain-sensing
wipers and fold in the mirrors
- Ensure all obstacles are out of the way of the
trunk lid when operating the Power Trunk
Smart Power Trunk (Continued)
OTHER KEY FEATURES
*IF EQUIPPED
ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLE TE OPER ATING INFORMATION AND SAFE T Y WARNINGS.

42
Map/Room Lamps
Automatic Turn Off Function
The interior lights automatically turn off approximately 20
seconds after the ENGINE START/STOP button is turned OFF.
Map/Room Lamp Operation
Map Lamps – These lights produce spot beams for
convenient use as map lamps or as personal lamps for the
driver or the front passenger. Press the buttons
A to turn the
map lamps ON/OFF.
ROOM button – Press the button
B to turn the front and
rear lamps ON/OFF.
REAR ROOM button – Press the button
C to turn the rear
lamp ON/OFF.
DOOR button – When the DOOR button
D is pressed (LED
lit) the front and rear lamps will turn ON as follows:
§
When a door is opened or doors are unlocked with the
Smart Key, the lamps will turn ON for approximately
30 seconds
§
If the ENGINE START/STOP button is in the ACC/OFF
position and a door is open, the lamps will stay ON for
approximately 20 minutes
§
If the ENGINE START/STOP button is in the ACC/ON
position and a door is open, the lamps will stay ON
The lamps will turn OFF immediately if the ENG INE STA RT/
STOP button is turned ON or all doors are locked.
PRIVACY button – When button
E is pressed (LED lit) and
a door is opened, that door lamp will turn ON.
REMINDER: When room lamp lens is pressed ON it
will remain ON, even when the map lamp switch is in
the OFF position. Quick Tips
- When doors are unlocked by the Smart Key, the
lamp turns ON for approximately 30 seconds
- If your vehicle is equipped with the theft alarm
system, the interior lights automatically turn off
approximately 3 seconds after the system is in
armed stage
- Using interior lights for an extended period of time
may cause battery discharge
BC
D
E
AA
OTHER KEY FEATURES
*IF EQUIPPED
OTHER KEY FEATURES
*IF EQUIPPED

45
How to Sync Transmitter with HomeLink®
If programming for the first time, begin with step 1 (repeating
this step will delete all information).
To program non-rolling and rolling code garage door openers
and other devices:
1. Press and hold the left F and center G buttons
simultaneously until the indicator light begins to flash (to
reprogram buttons, skip this step)
2. Press and hold the desired button F, G or H and hold
the button on the transmitter while it is approximately 1 to
3 inches away from the mirror. The HomeLink
® indicator
light will flash rapidly once the frequency signal has been
successfully programmed
To finish programming rolling code garage door openers,
complete these steps:
3. Locate the “learn” or “smart” button on the garage door’s
motor head unit. Press and release the button and complete
step 4 within 30 seconds
4. Firmly press and release the programmed HomeLink®
button up to three times
Quick Tips
- You can reprogram a single HomeLink® button by
repeating step 2
- Erasing programmed buttons will delete all
trained transmitters
Operating HomeLink®:
Press one of the programmed HomeLink
® buttons.
Erasing programmed buttons:
Press and hold the left
F and center H buttons
simultaneously for approximately 20 seconds, and then
release both buttons within 30 seconds.
If your garage door opener was manufactured in 2011
or later, and you are unable to program your vehicle’s
HomeLink
® system, you may need to purchase a
HomeLink® Repeater Kit. For more information, go to
www.HomeLink.com or call (800) 355-3515.
OTHER KEY FEATURES
*IF EQUIPPED
ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLE TE OPER ATING INFORMATION AND SAFE T Y WARNINGS.