2017 KIA FORTE 5 bulb

4 103
Features of your vehicle
If an indicator stays on and does not
flash or if it flashes abnormally, one of
the turn signal bulbs may be burned
out and will require replacement.
If an indicator flash is abnormally
quick or slow, a bulb may be burned
out or have a poor electrical connec-
tion in the circuit.One-touch lane change function
To activate an one-touch lane
change function, move the turn sig-
nal lever slightly and then release it.
The lane change signals will blink 3,
5 or 7 times.
You can choose one-touch lane
change blinking function in “One
touch turn lamp” of “User setting”.
Refer to “User setting” in chapter 4.
✽NOTICE
If an indicator flash is abnormally
quick or slow, the bulb may be
burned out or have a poor electrical
connection in the circuit.
Front fog light (if equipped)
Fog lights are used to provide
improved visibility when visibility is
poor due to fog, rain or snow, etc.
The fog lights will turn on when the
fog light switch (1) is turned to the on
position after the headlights are
turned on.
To turn off the fog lights, turn the
switch (1) to the off position.
When in operation, the fog lights
consume large amounts of vehicle
electrical power. Only use the fog
lights when visibility is poor.
OAM049046N

Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-69
• Instrument panel fuse replacement . . . . . . . . . . . . . . 7-70
• Engine compartment fuse replacement. . . . . . . . . . . 7-72
• Fuse/relay panel description. . . . . . . . . . . . . . . . . . . . 7-74
• Engine compartment fuse panel . . . . . . . . . . . . . . . . 7-75
• Engine room (Battery terminal cover) . . . . . . . . . . . 7-76
Light bulbs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-85
• Front lights replacement. . . . . . . . . . . . . . . . . . . . . . . 7-85
• Outside Mirrors with Turn Signal Indicators . . . . . 7-89
• Rear combination lamp bulb replacement . . . . . . . . 7-90
• High mounted stop lamp replacement . . . . . . . . . . . 7-95
• License plate lamp bulb replacement . . . . . . . . . . . . 7-97
• Interior lamp bulb replacement . . . . . . . . . . . . . . . . . 7-98
Appearance care . . . . . . . . . . . . . . . . . . . . . . . . . . 7-100
• Exterior care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-100
• Interior care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-105
Emission control system . . . . . . . . . . . . . . . . . . . 7-108
• Crankcase emission control system . . . . . . . . . . . . . 7-108
• Evaporative emission control (including ORVR:
Onboard Refueling Vapor Recovery) system . . . . 7-108
• Exhaust emission control system . . . . . . . . . . . . . . . 7-109
7

785
Maintenance
LIGHT BULBS
Use only the bulbs of the specified
wattage.
If you don’t have necessary tools, the
correct bulbs and the expertise, con-
sult an authorized Kia dealer. In
many cases, it is difficult to replace
vehicle light bulbs because other
parts of the vehicle must be removed
before you can get to the bulb. This is
especially true if you have to remove
the headlight assembly to get to the
bulb(s). Removing/installing the
headlight assembly can result in
damage to the vehicle.Front lights replacement
(1) Headlight (High)
(2) Headlight (Low)
(3) Front turn signal light
(4) Front fog light
(5) Front position light
(6) Side marker
WARNING - Lights
Prior to working on the light,
firmly apply the parking brake,
ensure that the ignition switch
is turned to the “LOCK” position
and turn off the lights to avoid
burning your fingers or receiv-
ing an electric shock.
CAUTION - Light
replacement
Be sure to replace the burned-
out bulb with one of the same
wattage rating. Otherwise, it
may cause damage to the fuse
or electric wiring system.
OYDM076048
OYD076034L
■4 Door, 5 Door
■2 Door

Maintenance
86 7
Headlight bulbAlways handle them carefully, and
avoid scratches and abrasions. If the
bulbs are lit, avoid contact with liq-
uids. Never touch the glass with bare
hands. Residual oil may cause the
bulb to overheat and burst when lit. A
bulb should be operated only when
installed in a headlight.
If a bulb becomes damaged or
cracked, replace it immediately and
carefully dispose of it.
Wear eye protection when changing
a bulb. Allow the bulb to cool down
before handling it.Headlight (bulb type)
1. Turn off the engine.
2. Open the hood.
3. Remove the headlight bulb cover
by turning it counterclockwise.
OHD076046
WARNING-Halogen
bulbs
Handle halogen bulbs with care.
Halogen bulbs contain pressur-
ized gas that will produce flying
pieces of glass if broken.
OYD076010L
OYDDMC20271
■4 Door, 5 Door
■2 Door
LowHIgh
LowHIgh

787
Maintenance
4. Disconnect the headlight bulb
socket-connector.
5. Remove the bulb from the head-
light assembly.
6. Install a new headlight bulb.
7. Connect the headlight bulb socket-
connector.
8. Install the headlight bulb cover by
turning it clockwise.
If the headlight aiming adjustment is
necessary after the headlight
assembly is reinstalled, consult an
authorized Kia dealer.Front side marker/Front turn sig-
nal light
1. Open the hood.
2. Disconnect the negative battery
cable.
3. Loosen the retaining bolts and
remove the headlamp assembly
from the body of the vehicle. If you
can reach to the bulb without
removing the headlamp assembly,
you don’t need to do step 3.
4. Disconnect the power connec
tor(s) from the back of the head
lamp assembly.Front side marker
5. Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
OYDDMC2043
OYDM076073
OYDNMC2058
■4 Door, 5 Door
■2 Door

Maintenance
88 7
6. Pull the bulb out of the socket.
7. Insert a new bulb.
8. Install the socket in the assembly
by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into assembly
and turn the socket clockwise.
9. Reinstall the headlamp assembly,
bumper to the body of the vehicle.
Front turn signal light
5. Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.6. Remove the bulb from the socket
by pressing it in and rotating it
counterclockwise until the tabs on
the bulb align with the slots in the
socket. Pull the bulb out of the
socket.
7. Insert a new bulb by inserting it
into the socket and rotating it until
it locks into place.
8. Install the socket in the assembly
by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into assembly
and turn the socket clockwise.
OYD076085L
OYDDMC2028
■4 Door, 5 Door
■2 Door

789
Maintenance
Front fog light (if equipped)1. Turn off the engine.
2. Remove the under cover by rotat-
ing the screws.
3. Reach your hand into the back of
the front bumper.
4. Disconnect the power connector.
5.Remove the bulb-socket from the
housing by turning the socket
counter clockwise until the tabs on
the socket align with the slots on
the housing.
6.Install the new bulb-socket into the
housing by aligning the tabs on the
socket with the slots in the hous-
ing.
Push the socket into the housing
and turn the socket clockwise.
7.Connect the power connector.
8.Reinstall the front under cover.Outside Mirrors with Turn
Signal Indicators (if equipped)
If the light (LED) does not operate,
have the vehicle checked by an
authorized Kia dealer
■5 Door Turbo
■4 Door, 5 Door
OYDM076083■2 Door
OYD076029
OYD076012L
OYDDMC2017

Maintenance
90 7
Rear combination lamp bulb
replacement
(1) Tail and Stop and Side marker lamp
(2) Tail and Side marker lamp
(3) Tail lamp
(4) Stop lamp
(5) Back up lamp
(6) Rear turn signal lamp
OYDM076079
OYDM076080
• 4 Door
Type A
• 4 Door
Type B
OYDDMC3075
OYDDMC3063
• 5 Door
Type A
• 5 Door
Type BOYD074021
OYD074019
• 2 Door
Type A
• 2 Door
Type B
(1) Stop and tail lamp
(2) Tail lamp
(3) Back-up lamp
(4) Rear turn signal lamp(5) Tail stop lamp or stop lamp
(LED)
If the light (LED) does not operate,
have the vehicle checked by an
authorized Kia dealer