2017 KIA BORREGO warning

853
Maintenance
FUSES
❈ Left side : Normal
Right side : blown
A vehicle’s electrical system is pro-
tected from electrical overload dam-
age by fuses. This vehicle has 5 fuse panels, one
located in the driver’s side panel bol-
ster, the others in the engine com-
partment near the battery.
If any of your vehicle’s lights, acces-
sories, or controls do not work, check
the appropriate circuit fuse. If the fuse
becomes disconnected, the electricalsystem it protected will not function
properly. Therefore, replace the fuse.
If the electrical system does not work,
first check the driver’s side fuse panel.
In order to replace the fuse, turn off
the engine and switch of all electrical
system first. Then, disconnect the
negative battery cable of the fuse and
replace at a level and safe location.
Always replace a blown fuse with
one of the same rating. If
the replace-
ment fuse blows, this indicates an elec-
trical problem. Avoid using the system
involved and we recommend that you
consult an authorized Kia dealer.
Three kinds of fuses are used: blade
type for lower amperage rating, car-tridge type, and fusible link for higheramperage ratings.
WARNING - Fuse replace- ment
Never replace a fuse with any- thing but another fuse of the same rating.
A higher capacity fuse could cause damage and possibly a
fire.
Never install a wire or alu- minum foil instead of the
proper fuse even as a tempo-
rary repair. It may cause
extensive wiring damage and
a possible fire.
Do not arbitrarily modify or add-on electric wiring of the
vehicle.
1VQA4037
Normal
Normal
Blade type
Cartridge type
Fusible link Blown
Blown
Normal Blown

Maintenance
56
8
Memory fuse (SHUNT connector)
Your vehicle is equipped with a mem-
ory fuse (SHUNT connector) to pre-
vent battery discharge if your vehicle
is parked without being operated for
prolonged periods. Use the following
procedures before parking the vehi-
cle for prolonged periods.
1. Turn off the engine.
2. Turn off the headlights and tail
lights.
3. Open the driver’s side panel cover and pull out the memory fuse (SHUNT connector).
✽✽ NOTICE
 If the memory fuse is pulled out from the fuse panel, the warning
chime, audio, clock and interior
lamps, etc., will not operate. Some
items must be reset after replace-
ment. Refer to “Battery” in this
section.
 Even though the memory fuse is pulled out, the battery can still be
discharged by operation of the
headlights or other electrical
devices.Engine compartment fuse replacement
1. Turn the ignition switch and all other switches off.
OHM078023OHM078024N
OHM078025N

Maintenance
60
8
DescriptionFuse ratingProtected component
PASS P/SEAT20APassenger Power Seat Switch
DRIVER P/SEAT30ADriver Power Seat Switch, Driver Lumbar Support Switch, IMS Control Module
ACC7.5AAudio, A/V & Navigation Head Unit, MTS E-Call Module, Smart Key Control Module,
Around View Monitor, JBL AMP
FRT CIGAR15ACigarette Lighter
START7.5ABurglar Alarm Relay, Start Relay
AIR BAG IND.7.5AInstrument Cluster(Air Bag IND.)
ABS7.5AABS Control Module, ESC Control Module, DBC Relay, Steering Angle Sensor,
Crash Pad Switch
IGN 17.5A
Rheostat, Air Suspention Control Module, Electro Chromic Mirror, Front Wiper Motor,
Smart Key Control Module, Multipurpose Check Connector, MTS E-Call Module,
Rear Parking Assist Buzzer, Rear Parking Assist Switch, Sport Mode Switch,
Audio, A/V & Navigation Head Unit, Stop Lamp Switch, Auto Head Lamp Leveling
Device Sensor, Alternator, Multifunction Switch, Tire Pressure Monitoring Module,
Blind Spot Detection Radar LH/RH, Tilt & Telescopic Module, Front A/C Control Module,
Instrument Cluster, Fuel Filter Warning Switch, Lane Departure Warning Control Module,
Front/Rear Parking Assist Sensor LH/RH, Front/Rear Parking Assist Sensor Center LH/RH
ENG7.5AECM, TCM, 4WD ECM, Air Flow Sensor, Smart Key Control Module, Inhibitor Switch,
Multipurpose Check Connector
AIR BAG15ASRS Control Module
DDM30ADriver Door Module, Driver Safety Power Window Motor
ADM30APassenger Door Sensor, Passenger Safety Power Window Motor

Maintenance
68
8
LIGHT BULBS
Please prepare bulbs with appropri- ate standards in case of emergen-
cies. (Refer to chapter 9 for further
information)
When changing bulbs and sorts, first
turn off the engine at a safe place,
firmly apply the side brake and take
out the battery's negative (-) terminal.
Use only the bulbs of the specified wattage.
WARNING - Working on the lights
Prior to working on the light,
firmly apply the parking brake,
ensure that the ignition switchis turned to the LOCK position
and turn off the lights to avoid
sudden movement of the vehi-
cle and burning your fingers or
receiving an electric shock.
WARNING
Be sure to replace the burned-
out bulb with one of the same
wattage rating. Otherwise, it
may cause extensive wiring
damage and possible fire.
CAUTION
If you don’t have necessary tools, the correct bulbs and theexpertise, consult an authorized Kia dealer. In many cases, it isdifficult to replace vehicle lightbulbs because other parts of the vehicle must be removed beforeyou can get to the bulb. This isespecially true if you have toremove the headlight assembly to get to the bulb(s). Removing/installing the headlight assem-bly can result in damage to the vehicle.
CAUTION
If unauthentic parts or sub- standard lights are used whenchanging lights, it may lead to fuse disconnection and mal-function, and other wiringdamages.
Do not install extra lamps or LED to the vehicle. If supple-mentary lights are installed, itmay lead to lamp malfunctionand flickering of the lights. In addition, the fuse box andother writing may be damaged.

Maintenance
70
8
Headlamp, Front position lamp,
Front turn signal lamp, Front
fog lamp bulb replacement (1) Headlamp (High)
(2) Headlamp (Low)
(3) Front turn signal lamp
(4) Front position lamp /
Daytime running lamp (LED)*
(5) Front fog lamp (Bulb)
* : if equippedHeadlamp bulb
OHM076030L
(Continued) A bulb should be operated
only when installed in a head-light.
If a bulb becomes damaged or cracked, replace it immediate-
ly and carefully dispose of it.
Wear eye protection when changing a bulb. Allow the
bulb to cool down before han-dling it.
OHD076046
WARNING - Halogen
bulbs
Halogen bulbs contain pres- surized gas that will produce
flying pieces of glass if broken.
Always handle them carefully, and avoid scratches and abra-
sions. If the bulbs are lit, avoid
contact with liquids. Never
touch the glass with bare
hands. Residual oil may cause
the bulb to overheat and burstwhen lit.
(Continued)

871
Maintenance
1. Open the hood.
2. Remove the headlight bulb coverby turning it counterclockwise.
3. Disconnect the headlight bulb socket-connector.
4. Unsnap the headlight bulb retain- ing wire by depressing the end
and pushing it upward.
5. Remove the bulb from the head- light assembly.
6. Install a new headlight bulb and snap the headlight bulb retaining
wire into position by aligning the
wire with the groove on the bulb. 7. Connect the headlight bulb socket-
connector.
8. Install the headlight bulb cover by turning it clockwise.
✽✽ NOTICE
If the headlight aiming adjustment
is necessary after the headlight
assembly is reinstalled, we recom-
mend that you consult an authorized
Kia dealer.
Headlight (HID type), position, turn signal, and front fog light bulb replacement
If the light bulb does not operate, we
recommend that you have the vehi-
cle checked by an authorized Kia
dealer.
OEN076051
WARNING
- HID Headlight low beam (if equipped)
Do not attempt to replace or
inspect the low beam (XENON
bulb) due to electric shock dan-
ger. If the low beam (XENON
bulb) is not working, we recom-
mend that you have your vehi-
cle checked by an authorized
Kia dealer.

Maintenance
76
8
Interior light bulb replacement
1. Using a flat-blade screwdriver,
gently pry the lens from the interi- or light housing.
2. Remove the bulb by pulling it straight out.
3. Install a new bulb in the socket.
4. Align the lens tabs with the interior light housing notches and snap
the lens into place.Luggage lamp Map lamp
OHM078054/OHM078053
Vanity mirror lampRoom lamp
Glove box lamp OHM076051/OHM076052/OHM079055
WARNING
Prior to working on the Interior
Lights, ensure that the “OFF”
button is depressed to avoid
burning your fingers or receiv-
ing an electric shock.
CAUTION
Be careful not to dirty or dam- age the lens, lens tab, and plas-tic housings.

877
Maintenance
Exterior care
Exterior general caution
It is very important to follow the label
directions when using any chemical
cleaner or polish. Read all warningand caution statements that appearon the label.
Finish maintenance
Washing
To help protect your vehicle’s finish
from rust and deterioration, wash itthoroughly and frequently at least
once a month with lukewarm or cold
water.
If you use your vehicle for off-road
driving, you should wash it after each
off-road trip. Pay special attention to
the removal of any accumulation of
salt, dirt, mud, and other foreign mate-
rials. Make sure the drain holes in the
lower edges of the doors and rocker
panels are kept clear and clean.
Insects, tar, tree sap, bird droppings,
industrial pollution and similar
deposits can damage your vehicle’s
finish if not removed immediately.
Even prompt washing with plain water
may not completely remove all these
deposits. A mild soap, safe for use on
painted surfaces, may be used.
After washing, rinse the vehicle thor-
oughly with lukewarm or cold water.
Do not allow soap to dry on the finish.
APPEARANCE CARE
WARNING -
Wet brakes
After washing the vehicle, test
the brakes while driving slowly
to see if they have been affected
by water. If braking performance
is impaired, dry the brakes by
applying them lightly while main-
taining a slow forward speed.
CAUTION
Do not use strong soap, chem- ical detergents or hot water,and do not wash the vehicle in direct sunlight or when thebody of the vehicle is warm.
Be careful when washing the side windows of your vehicle.
Especially, with high-pressurewater, water may leak throughthe windows and wet the inte- rior.
To prevent damage to the plastic parts and lamps, donot clean with chemical sol-vents or strong detergents.