2017 JEEP WRANGLER lock

POWER WINDOWS — IF EQUIPPED
The power window switches are located on the instrument
panel below the radio. Push the switch downward to open
the window and upward to close the window.
The top left switch controls the left front window and the
top right switch controls the right front window.
WARNING!
Never leave children unattended in a vehicle, and do
not let children play with power windows. Do not
leave the key fob in or near the vehicle, or in a location
accessible to children. Occupants, particularly unat-
tended children, can become entrapped by the win-
dows while operating the power window switches.
Such entrapment may result in serious injury or death.NOTE:
•
For vehicles not equipped with the instrument cluster
display, the power window switches will remain active
for 45 seconds after the ignition switch is turned to the
LOCK position. Opening either front door will cancel
this feature.
• For vehicles equipped with the instrument cluster dis-
play, the power window switches will remain active for
up to 10 minutes after the ignition switch is turned to the
LOCK position. Opening either front door will cancel
this feature.
Power Window Switches
3
GETTING TO KNOW YOUR VEHICLE 71

Installing The Soft Top — Four-Door Models
NOTE:The following procedures are for first time set up
only. For future soft top procedures, refer to “Soft Top” in
this section.
1. Locate and remove the following items prior to hard top removal:
• Right and left door frames
• Six door frame attachment knobs
• Right and left quarter windows
• Rear window
2. Remove the hard top. Refer to “Freedom Top Three- Piece Modular Hard Top — Front/Rear Panel Removal”
in this section.
3. Install the door frames. Refer to “Door Frame” in this section.
4. Install the soft top with the pivot brackets above the sport bar brackets, lower the soft top into the sport bar
bracket slots in a downward motion to lock tab on soft
top. You will need to lift the top to get the brackets to
line up. (Another person may be needed to help with
this operation.) NOTE:
If you are doing this alone, use one arm to hold the
soft top up, the other to align the brackets.
Step Four
80 GETTING TO KNOW YOUR VEHICLE

5. Lower the pivot bracket onto the sport bar bracketmounting tab in a downward motion to lock into tab.
6. Install the pivot bracket bolts back into place using a 10.0 mm wrench or socket driver. Secure them until they
are snug, being careful not to cross-thread the screws or
overtighten.
CAUTION!
Do not overtighten the screws. You can strip the screws
if they are overtightened. 7. Remove the tether strap from the pivot bracket.
Step Five
Step Seven
3
GETTING TO KNOW YOUR VEHICLE 81

CAUTION!(Continued)
•Careless handling and storage of the removable roof
panels may damage the seals, causing water to leak
into the vehicle’s interior.
• The front panel(s) must be positioned properly to
ensure sealing. Improper installation can cause water
to leak into the vehicle’s interior.
Front Panel(s) Removal
NOTE: Left panel must be removed before removing
right panel.
1. Fold down the sun visor, and move it to the side. 2. Turn the rear fasteners (knobs) (located on the overhead
speaker bar assembly) counterclockwise until they can
be removed.
Step Two
84 GETTING TO KNOW YOUR VEHICLE

3. Turn the center L-shaped locks (two) from the center ofthe roof panel. 4. Turn the rear L-shaped lock (located above the shoulder
belt anchorage).
Step ThreeStep Four
3
GETTING TO KNOW YOUR VEHICLE 85

Front Panel(s) Installation
NOTE:Set the panels on the windshield frame so that
there is no overhang. Also, make sure that the panels are
sitting flush with the body.
1. Install the right panel first, then the left panel.
2. Reinstall the panel(s) using the same steps for removal in reverse order.
Front Panel(s) Installation With Rear Hard Top
Removed
1. Turn the left and right panels over and move the spacerblock (located on the rear of the panel) upward 90
degrees. NOTE:
The front panel(s) must be positioned properly to
ensure sealing. Set the panels on the windshield frame so
that there is no overhang. Also, make sure that the panels
are sitting flush with the body.
2. Install the right panel first, then the left panel.
3. Reinstall the panel(s) using the same steps for removal in reverse order.Step One
90 GETTING TO KNOW YOUR VEHICLE

6. Locate the wire harness on the left rear inside corner ofthe vehicle. 7. Release the red locking tab by pulling outward to the
right.
Wire Harness ConnectorRed Locking Tab
92 GETTING TO KNOW YOUR VEHICLE

4. Release the sail panel retainers from the body sidechannel at the rear corners of the vehicle.
NOTE: When releasing the sail panel retainers, it is helpful
to pull down on the rear roof bow. 5. Make sure the plastic sleeves are slid rearward over the
Sunrider link to lock in the link (Sunrider Models only).
Step FourStep Five
104 GETTING TO KNOW YOUR VEHICLE