2017 INFINITI QX60 HYBRID wheel

3-3 Vehicle Immobilization and Stabilization
If
possible, immobilize the vehicle by turning the 12-volt system OFF and stabilize it with a wheel chock(s) .
Stabilize the vehicle with wooden blocks or by removing air from the tires. • To avoid electrical shock, do not put wooden blocks or wheel chock(s) under the
high-voltage
components and harnesses as shown following. =
AAYIA0486ZZ
RAG–17

4-3 Towing
4-3.1
Vehicle Specifications Length
196.4
in. (4,989 mm)
Width 77.2 in. (1,960 mm)
Overall Height 68.6 in. (1,742 mm)
Wheel Base 114.2 in. (2,900 mm)
Minimum ground clearance 6.5 in. (165 mm)
Overall vehicle weight 4,598.6 - 4,737.9 lbs. (2,085.9 - 2,149.1 kg)
(Weight varies by equipment and trim level.)
Front approach angle 14°
Rear departure angle 20.6°
4-3.2 Towing Guidelines
Infiniti strongly recommends that QX60 HYBRID be towed with the driving wheels off the ground or that the
vehicle be placed on a flatbed truck. • AWD Models: Never tow with any of the wheels on the ground, as this may cause
serious
and expensive damage to the powertrain.
• FWD Models: Never tow with the front wheels on the ground, as this may cause serious and expensive damage to the powertrain.
• Transport the vehicle only after turning the ignition switch OFF.
• Safety chains or cables must be attached only to the main structural members of the vehicle. Otherwise, the vehicle body will be damaged.
• Do not use the vehicle tie down points to free a vehicle stuck in sand, snow, mud, etc.
• Never tow a vehicle using the vehicle tie down.
• Always pull the recovery device straight out from the vehicle. Never pull on the vehicle at an angle.
• Pulling devices should be routed so they do not touch any part of the suspension, steering, brake, high-voltage or cooling systems.
• Pulling devices such as ropes or canvas straps are not recommended for use in vehicle towing or recovery.
RAG–24

Perform vehicle towing by holding up drive wheels (front or all, depending on model) or on flatbed in order
to
prevent secondary damage from voltage generated by the motor. In addition, turn the ignition switch OFF
when towing the vehicle. Refer to the following illustration:
AWD Models
FWD Models AAYIA0384ZZ
AAYIA0355ZZ
RAG–25

4-4 Jacking Up the Vehicle and Changing a Tire
Always follow these instructions when jacking up the vehicle and changing a tire:
•
Never change a tire when the vehicle is on a slope, ice or slippery areas. Jack must be on
level ground.
• Make sure the parking brake is securely applied and shift selector is in P (Park) position.
• Never get under the vehicle while it is supported only by the jack. If it is necessary to work under the vehicle, support it with safety stands.
• Use the correct jack-up points. Never use any other part of the vehicle for jack support.
• Never jack up the vehicle more than necessary.
• Never use blocks on or under the jack.
• Do not start or run the engine while vehicle is on the jack. It may cause the vehicle to move. This is especially true for vehicles with limited slip differentials.
• Do not allow passengers to stay in the vehicle while it is on the jack.
• Never run the engine with a wheel(s) off the ground. It may cause the vehicle to move.
• Be sure to block the wheel diagonally opposite the wheel being removed as the vehicle may move and result in personal injury.
Failure to follow these instructions can result in serious personal injury or death and/or
vehicle damage.
1. Open the liftgate and lift the luggage board in the cargoarea using the handle (A) .
2. Remove the jack and tool kit cover by lifting up using the handles. AAYIA0267ZZ
AAYIA0368ZZ
RAG–27

3. Remove the tool kit.
a. To release the tool kit, release the straps (A) .
4. Remove the jack (B) , winch socket (C) , extension (D) and wheel nut wrench (E) .
5. The lowering mechanism for the spare tire is located on the passenger side of the cargo area. Remove the cover
to access the spare tire winch.
6. Place the spare tire winch socket onto the lowering mechanism nut.
7. To lower the spare tire, insert the wheel nut wrench (E) to the extension (D) and insert the T-shaped end to the
winch socket (C) and rotate counterclockwise.
8. After removing the spare tire from under the vehicle, be sure to crank the cable up to stow it.
9.
Loosen each wheel nut one or two turns by turning it counterclockwise with the wheel nut wrench.
Do not remove the wheel nuts until the tire is off the ground. AAYIA0369ZZ
AAYIA0370ZZ
AAYIA0371ZZ
AAYIA0372ZZ
RAG–28

10. Place the jack directly under the jack-up point as illustrated so the top of the jack contacts the
vehicle at the jack-up point. Align the jack head between the two notches in the front or the rear
as shown. Also fit the groove of the jack head between the notches as shown. The jack should
be used on level firm ground.
11. To lift the vehicle, securely hold the jack lever and rod with both hands as shown. Carefully raise the vehicle until the tire clears the ground. Remove the wheel nuts, and then remove the tire.
12. Install new or repaired tire and hand-tighten the wheel nuts with the wheel nut wrench in an alternating pattern. Always follow these instructions when changing a tire:
•

Incorrect wheel nuts or improperly tightened wheel
nuts can cause the wheel to become loose or come
off. This could cause an accident.
• Do not use oil or grease on the wheel studs or nuts. This could cause the nuts to become loose.
Failure to follow these instructions can result in serious
personal injury or death and/or vehicle damage.
13. Securely torque the wheel nuts in an alternating pattern to 83 ft-lb (113 Nm) . AAYIA0373ZZ
AAYIA0136ZZ
AAYIA0137ZZ
RAG–29