2017 INFINITI QX30 wiper blades

A visual and audible alarm is triggered if the
alarm system is armed and you open:
•A door.
•The vehicle with the emergency key element.
•The lift gate.
•The hood.
To switch the alarm off with the key: press the
orbutton on the key. The alarm is
switched off
The alarm is not switched off, even if you close
the open door that has triggered it, for example.
WARNING
In freezing temperatures the washer solution
may freeze on the windshield and obscure your
vision which may lead to an accident. Warm
the windshield with the defroster before you
wash the windshield.
CAUTION
•Do not operate the washer continuously for
more than 30 seconds.
•Do not operate the washer if the window
washer fluid reservoir is empty.
•Do not fill the window washer reservoir tank
with washer fluid concentrates at full
strength. Some methyl alcohol based
washer fluid concentrates may permanently
stain the grille if spilled while filling the
window washer reservoir tank.
•Pre-mix washer fluid concentrates with wa-
ter to the manufacturer’s recommended lev-
els before pouring the fluid into the window
washer reservoir tank. Do not use the win-
dow washer reservoir tank to mix the
washer fluid concentrate and water.NOTE
•If the wiper operation is interrupted by snow
or ice, the wiper may stop moving to protect
its motor. If this occurs, turn the wiper switch
to the “OFF” position and remove the snow
or ice on and around the wiper arms. In
approximately 1 minute, turn the switch on
again to operate the wiper.
•Do not operate the windshield wipers when
the windshield is dry, as this could damage
the wiper blades. Moreover, dust that has
collected on the windshield can scratch the
glass if wiping takes place when the wind-
shield is dry.
•If it is necessary to switch on the wipers in
dry weather conditions, always operate them
using washer fluid.
•If the windshield wipers leave smears on the
windshield after the vehicle has been
washed in an automatic car wash, this may
be due to wax or other residue. Clean the
windshield with washer fluid after an auto-
matic car wash.
WIPER AND WASHER SWITCH
2-58Instruments and controls

SWITCHING THE WINDSHIELD WIPERS
ON/OFF
1Windshield wipers off.
2Intermittent wipe, low (rain sen-
sor set to low sensitivity).
3Intermittent wipe, high (rain sen-
sor set to high sensitivity).
4Continuous wipe, slow.
5Continuous wipe, fast.
ASingle wipe/
wipe the windshield using washer fluid.
The windshield wiper and washer operate when
the ignition switch is in the ON position.
Turn the combination switch to the desired
position.
Rain sensor (if equipped)
CAUTION
•Do not touch the rain sensor and around it
when the wiper switch is in theorposition and the ignition switch is in
the ON position. The wipers may operate
unexpectedly and cause an injury or may
damage a wiper.
•The rain-sensing auto wipers are intended
for use during rain. If the switch is left in the
orposition, the wipers may
operate unexpectedly when dirt, finger-
prints, oil film or insects are stuck on or
around the sensor. The wipers may also op-
erate when exhaust gas or moisture affect
the rain sensor.
•When the windshield glass is coated with
water repellent, the speed of the rain-
sensing auto wipers may be higher even
though the amount of the rainfall is small.
•Be sure to turn off the rain-sensing auto
wiper system when you use a car wash.
•The rain-sensing auto wipers may not oper-
ate if rain does not hit the rain sensor even if
it is raining.
•Using genuine wiper blades is recom-
mended for proper operation of the rain-
sensing auto wiper system. For additional
information, refer toWiper bladesin the
8. Do-it-yourselfsection.
•Vehicles with a rain sensor: if the wind-
shield becomes dirty in dry weather condi-
tions, the windshield wipers may be acti-
vated inadvertently. This could damage the
windshield wiper blades or scratch the
windshield.
For this reason, you should always switch
off the windshield wipers in dry weather.
Vehicles with a rain sensor: in the
orposition, the appropriate wiping fre-
quency is automatically set according to the
intensity of the rain. In the
position, the
rain sensor is more sensitive than in the
position, causing the windshield wiper to wipe
more frequently.
If the wiper blades are worn, the windshield will
no longer be wiped properly. This could prevent
you from observing the traffic conditions.
The rain-sensing auto wiper system uses the
rain sensor located on the upper part of the
windshield.
NIC2810Combination switch
Instruments and controls2-59

8 Do-it-yourself
Maintenance precautions..................8-2
Engine compartment check locations...........8-3
2.0L Gasoline engine...................8-3
Engine cooling system....................8-3
Checking engine coolant level.............8-4
Changing engine coolant................8-5
Engine oil............................8-5
Checking engine oil level................8-5
Changing engine oil...................8-5
Changing engine oil filter................8-6
Automatic Transmission Fluid (ATF)............8-7
Brake fluid...........................8-7
Window washer fluid.....................8-8
Battery.............................8-9
Accessing Vehicle battery...............8-10
Maintenance free battery................8-10
Models with Idle Stop/Start System.........8-11
Battery replacement...................8-11
Reinitialisation procedure after battery
reconnection.......................8-12
Jump-starting.......................8-12
Drive belt...........................8-12
Spark plugs..........................8-13
Air cleaner filter.......................8-13
Wiper blades.........................8-13Cleaning..........................8-13
Replacing front window wiper blades........8-14
Replacing rear window wiper blade..........8-15
Brakes.............................8-17
Self-adjusting brakes..................8-17
Fuses..............................8-17
Before replacing a fuse.................8-17
Engine compartment...................8-17
Passenger compartment................8-18
Intelligent key battery replacement..........
.8-20
Checking the battery..................8-20
Replacing the battery..................8-20
Lights.............................8-22
Exterior and interior lights...............8-22
Replacement procedures................8-24
Wheels and tires.......................8-27
Tire Pressure.......................8-27
Tire inflation pressure.................8-29
Tire labeling.......................8-30
Types of tires.......................8-31
Tire chains........................8-33
Tire wear and damage.................8-33
Tire rotation.......................8-34
Replacing wheels and tires..............8-34
Wheel balance......................8-36

Replace the spark plugs according to the main-
tenance schedule shown in a separate mainte-
nance booklet.
If replacement is required, it is recommended
that you visit an INFINITI retailer.
Always replace spark plugs with recommended
or equivalent ones.
WARNING
Be sure the engine and ignition switch are off
and that the parking brake is engaged
securely.
CAUTION
•Be sure to use the correct socket to remove
the spark plugs. An incorrect socket can
cause damage to the spark plugs.It is recommended that you visit an INFINITI
retailer if checking or replacement is required.
WARNING
•Operating the engine with the air cleaner
filter off can cause you or others to be
burned. The air cleaner filter not only cleans
the intake air, it also stops the flame if the
engine backfires. If the air cleaner is not
installed and the engine backfires, you
could be burned. Never drive with the air
cleaner filter off. Be cautious working on the
engine when the air cleaner is off.
•Never pour fuel into the throttle body or
attempt to start the engine with the air
cleaner removed. Doing so could result in
serious injury.
CLEANING
If the windshield or rear window is not clear
after using the window washer or if a wiper
blade chatters when running, wax or other
material may be on the blade or windshield.
Clean the outside of the windshield or rear
window with a washer solution or a mild deter-
gent. The windshield or rear window is clean if
beads do not form when rinsing with clear
water.
Clean the blade by wiping it with a cloth soaked
in a washer solution or a mild detergent. Then
rinse the blade with clear water. If the wind-
shield or rear window is still not clear after
cleaning the blades and using the wiper, re-
place the blades.
CAUTION
Worn windshield wiper blades can damage the
windshield and impair driver vision.
SPARK PLUGS AIR CLEANER FILTER WIPER BLADES
Do-it-yourself8-13

REPLACING FRONT WINDOW WIPER
BLADES
Replace the wiper blades if they are worn. To
replace the windshield wiper blades, follow the
procedure below:1. Move the wiper arm away from the wind-
shield.
2. Press both release clips
2.
3. Move the wiper blade
1in the direction of
arrow
3away from wiper arm4.
4. Remove wiper blade
1in the direction of
arrow
5.
5. Position new wiper blade
1with recess6on lug5.
6. Move wiper blade
1in the direction of
arrow
3onto the wiper arm until retaining
clips
2engage in bracket4.
NDI1586NDI1587
8-14Do-it-yourself

7. Make sure that wiper blade1is seated
correctly.
8. Move the wiper arm back onto the wind-
shield.
CAUTION
•After wiper blade replacement, return the
wiper arm to its original position; otherwise
it may be damaged when the hood is
opened.
•Make sure the wiper blades contact the
glass; otherwise the arms may be damaged
from wind pressure.If you wax the surface of the engine hood, be
careful not to let wax get into the washer nozzle
A. This may cause clogging or improper wind-
shield washer operation. If wax gets into the
nozzle, remove it with a needle or small pin
B.
REPLACING REAR WINDOW WIPER
BLADE
Replace the wiper blades if they are worn. To
replace the rear window wiper blade, follow the
procedure below:
1. Move wiper arm
4away from the rear window.
NDI892Z
NDI1588
Do-it-yourself8-15

released. When driving in areas using road salt
or other corrosive materials, check lubrication
frequently.
Lights*
:
Clean the headlights on a regular basis. Make
sure that the headlights, stop lights, tail lights,
turn signal lights, and other lights are all oper-
ating properly and installed securely. Also
check the aim of the headlights.
Road wheel nuts (lug nuts)*
:
When checking the tires, make sure no wheel
nuts are missing, and check for any loose wheel
nuts. Tighten if necessary.
Tire rotation*
:
Tires should be rotated every 5,000 miles
(8,000 km). Tires marked with directional indi-
cators can only be rotated between front and
rear. Make sure that the directional indicators
point in the direction of wheel rotation after the
tire rotation is completed.
Tires*
:
Check the pressure with a gauge often and
always prior to long distance trips. Adjust the
pressure in all tires to the pressure specified.
Check carefully for damage, cuts or excessive
wear.Tire Pressure Monitoring System (TPMS) trans-
mitter components
:
Replace the TPMS transmitter grommet seal,
valve core and cap when the tires are replaced
due to wear or age.
Wheel alignment and balance
:
If the vehicle should pull to either side while
driving on a straight and level road, or if you
detect uneven or abnormal tire wear, there may
be a need for wheel alignment.
If the steering wheel or seat vibrates at normal
highway speeds, wheel balancing may be
needed.
For additional information regarding tires, refer
to “Important Tire Safety Information” (US) or
“Tire Safety Information” (Canada) in the
INFINITI Warranty Information Booklet.
Windshield
:
Clean the windshield on a regular basis. Check
the windshield at least every six months for
cracks or other damage. Have a damaged wind-
shield repaired by a qualified repair facility.
Wiper blades*
:
Check for cracks or wear if not functioning
correctly. Replace as necessary.
Inside the vehicle
The maintenance items listed here should be
checked on a regular basis, such as when
performing scheduled maintenance, cleaning
the vehicle, etc.
Accelerator pedal
:
Check the pedal for smooth operation and make
sure that the pedal does not catch or require
uneven effort. Keep the floor mat away from the
pedal.
Automatic transmission P (Park) mechanism
:
On a fairly steep hill, check that your vehicle is
held securely when P (Park) has been activated,
without applying any brakes.
Brake pedal*
:
Check the pedal for smooth operation. If the
brake pedal suddenly goes down further than
normal, the pedal feels spongy or the vehicle
seems to take longer to stop, have your vehicle
checked immediately. It is recommended you
visit an INFINITI retailer for this service. Keep
the floor mat away from the pedal.
Brakes
:
Check that the brakes do not pull the vehicle to
one side when applied.
Maintenance and Schedules9-3

Parkingsensors .................5-79
OFF switch...................5-79
Phone.......................4-88
During a call.................4-90
Favorites....................4-97
Makingacall.................4-88
Phonebook..................4-97
Receiving a call................4-89
Selection...................4-88
Settings....................4-94
Power........................3-6
Door lock switch................3-6
Outlet .....................2-75
Seat adjustment................1-4
Steering....................5-86
Windows....................2-71
Precautions....................4-53
Audio......................4-53
Boosterseats.................1-36
Brake......................5-87
Child restraints................1-20
Intelligent Parking Assist (IPA).......5-68
Maintenance..................8-2
Safety......................4-2
Seatbeltusage ................1-11
Starting and driving..............5-4
Supplemental Restraint System.......1-39
Tire Pressure Monitoring System (TPMS) . .5-5
Pregnant women.................1-13
Protection.....................7-7
Corrosion....................7-7Push-starting...................6-12
Rearseats .....................1-5
Folding......................1-6
RearViewmonitor.................4-17
Maintenance .................4-24
Repairing.....................8-24
Headlights...................8-24
Replacement...................1-56
Air bags....................1-56
Air cleaner filter................8-13
Enginecoolant.................8-5
Engineoil....................8-5
Engine oil filter.................8-6
Intelligent Key battery............8-20
Sparkplugs..................8-13
Tires and wheels...............8-34
Wiperblades .................8-13
Roof........................2-74
Glass......................2-74
Sunshade operation.............2-74
Roof Rack.....................2-82
Safety.......................1-18
Children ...................
.1-18
Child safety rear door locks..........3-7
Head restraints.................1-7
Injuredpersons................1-13
Precautions...................4-2
Pregnant women................1-13
Reporting safety defects..........10-18
Seat belts..................1-11, 1-14
Adjustment...................1-16Children-Infants...............1-18
Children - Larger...............1-19
Children - Small................1-19
Child safety..................1-18
Cleaning.....................7-5
Maintenance..................1-17
Overview....................0-2
Precautions...................1-11
Warninglight .................2-11
Warnings....................1-14
Seats........................1-2
Adjustment...................1-4
Adjustment(Manual)..............1-3
Booster seats.................1-36
Head restraints.................1-7
Heating....................2-69
Leather .....................7-6
Memory....................3-20
Overview....................0-2
Rear .......................1-5
Rear seats - Folding..............1-6
Seatbelts....................1-11
Security system.................2-57
Servicing.....................4-52
Air conditioner................4-52
Sparkplugs....................8-13
Information..................8-13
Replacement..................8-13
Speedometer....................2-5
Starting......................5-15
Before starting the engine..........5-15
Index11-5