2017 INFINITI QX30 service indicator

Message Possible causes/consequences and solutions
[Front Passenger Airbag
Disabled See Operator’s
Manual]The front-passenger front air bag is disabled during the journey although an adult or person of corresponding stature is on the front
passenger seat.
Front passenger seat adult occupants who are properly seated and using the seat belt as outlined in this manual should not cause the
front passenger air bag to be automatically turned OFF. For small adults it may be turned OFF, however if the occupant takes his/her
weight off the seat cushion (for example, by not sitting upright, by sitting on an edge of the seat, or by otherwise being out of position),
this could cause the sensor to turn the air bag OFF. Always be sure to be seated and wearing the seat belt properly for the most effective
protection by the seat belt and supplemental air bag.
If additional forces are applied to the seat, the system may interpret the occupant’s weight as lower than it actually is.
1. Stop the vehicle in a safe area away from traffic as soon as possible, paying attention to road and traffic conditions.
2. Secure the vehicle against rolling away.
3. Switch the ignition off.
4. Have the occupant on the front-passenger seat step out of the vehicle.
5. Make sure that the seat is unoccupied, close the front passenger door and switch on the ignition.
6. Observe the indicator lights in the center console and the vehicle information display and check the following.
Seat unoccupied and ignition switched on:
- The and indicator lights must light up simultaneously for approximately six
seconds.
- The indicator lights must then light up and remain lit. If the indicator light is on, the automatic
front-passenger front air bag deactivation system has disabled the front-passenger front air bag (seeFront passenger air bag and
status lightin the1. Safety — seats, seat belts and supplemental restraint systemsection)
- the [Front Passenger Airbag Enabled See Operator’s Manual] or [Front Passenger Airbag Disabled See Operator’s Manual] display
messages must not be shown in the vehicle information display.
7. Wait for a period of at least 60 seconds until the necessary system checks have been completed.
8. Make sure that the display messages do not appear in the vehicle information display.
If these conditions are met, the front-passenger seat can be occupied again. Whether the or indicator
light remains lit or goes out depends on how the automatic front passenger front air bag deactivation system classifies the occupant.
If the conditions are not met, the system is not operating correctly.
Have the system checked immediately. It is recommended you visit an INFINITI retailer for this service.
For further information on the automatic front-passenger front air bag deactivation feature (seeFront passenger air bag and status light
in the1. Safety — seats, seat belts and supplemental restraint systemsection).
2-38Instruments and controls

Message Possible causes/consequences and solutions
[Front Passenger Airbag
Enabled See Operator’s
Manual]The front-passenger front air bag is enabled during the journey although:
•A child or child restraint as specified in U.S. regulations is located on the front-passenger seat.
or
•The front-passenger seat is not occupied.
The system may detect objects or forces that are adding to the weight applied to the seat.
1. Stop the vehicle in a safe area away from traffic as soon as possible, paying attention to road and traffic conditions.
2. Secure the vehicle against rolling away.
3. Switch the ignition off.
4. Open the front-passenger door.
5. Remove the child and the child restraint system from the front passenger seat.
6. Make sure there are no objects applying additional force to the seat. The system may otherwise detect the additional force and
interpret the seat occupant’s weight as greater than it actually is.
7. Make sure that the seat is unoccupied, close the front passenger door and switch on the ignition.
8. Observe the indicator lights in the center console and the vehicle information display and check the following.
Seat unoccupied and ignition switched on:
- The and indicator lights must light up simultaneously for approximately six
seconds.
- The indicator light must then light up and remain lit. If the indicator light is on, the automatic
front-passenger front air bag deactivation system has disabled the front-passenger front air bag (seeFront passenger air bag and
status lightin the1. Safety — seats, seat belts and supplemental restraint systemsection).
- the [Front Passenger Airbag Enabled See Operator’s Manual] or [Front Passenger Airbag Disabled See Operator’s Manual] display
messages must not be shown in the vehicle information display.
7. Wait for a period of at least 60 seconds until the necessary system checks have been completed.
8. Make sure that the display messages do not appear in the vehicle information display.
If these conditions are met, the front-passenger seat can be occupied again. Whether the or indicator
light remains lit or goes out depends on how the automatic front passenger front air bag deactivation system classifies the occupant.
If the conditions are not met, the system is not operating correctly.
Have the system checked immediately. It is recommended you visit an INFINITI retailer for this service.
For further information on the automatic front-passenger front air bag deactivation feature (seeFront passenger air bag and status light
in the1. Safety — seats, seat belts and supplemental restraint systemsection).
Instruments and controls2-39

Driving systems
Message Possible causes/consequences and solutions
[Lane Departure Warning
Currently Unavailable See
Operator’s Manual]Lane Departure Warning is deactivated and temporarily inoperative.
Possible causes:
•The windshield is dirty in the camera’s field of vision.•Visibility is impaired due to heavy rain, snow or fog.•There have been no lane markings for an extended period.•The lane markings are worn, dark or covered, e.g. by dirt or snow.
Once the causes listed above no longer apply, the display message goes out.
Lane Departure Warning is operational again.
If the display message does not disappear:
1. Pull over and stop the vehicle safely as soon as possible, paying attention to road and traffic conditions, and switch off the engine.
2. Secure the vehicle against rolling away.
3. Clean the windshield
[Lane Departure Warning
Inoperative]Lane Departure Warning is faulty.
Have the system checked. It is recommended you visit an INFINITI retailer for this service.
[Blind Spot Warning Cur-
rently Unavailable See Op-
erator’s Manual]Blind Spot Warning is temporarily inoperative. Possible causes:
•The function is impaired due to heavy rain or snow.•The radar sensor system is temporarily inoperative, e.g. due to electromagnetic radiation emitted by nearby TV or radio stations or
other sources of electromagnetic radiation.
•The radar sensor system is outside the operating temperature range.
The yellow indicator lights also light up in the exterior mirrors.
Once the causes listed above no longer apply, the display message goes out.
Blind Spot Warning is operational again.
If the display message does not disappear:
1. Pull over and stop the vehicle safely as soon as possible, paying attention to road and traffic conditions, and switch off the engine.
2. Secure the vehicle against rolling away.
3. Restart the engine
2-46Instruments and controls

Message Possible causes/consequences and solutions
[Blind Spot Warning Not
Available When Towing a
Trailer See Operator’s
Manual]Blind Spot Warning is deactivated while towing a trailer.
You have established the electrical connection between the trailer and your vehicle.
Press on the steering wheel to confirm the display message.
[Blind Spot Warning
Inoperative]Blind Spot Warning (BSW) is faulty.
The BSW indicator lights also light up.
Have the system checked. It is recommended you visit an INFINITI retailer for this service.
[Park Assist Canceled] The driver’s door is open and the driver’s seat belt has not been fastened.
Repeat the parking process with the seat belt fastened and the driver’s door closed.
You inadvertently touched the steering wheel while steering intervention was active.
While steering intervention is active, make sure not to touch the steering wheel.
The vehicle has started to skid and VDC has intervened.
Use Intelligent Park Assist again later.
[Park Assist Inoperative] You have just carried out a large number of turning or parking maneuvers.
Intelligent Park Assist will become available again after approximately ten minutes.
1. Pull over and stop the vehicle safely as soon as possible, paying attention to road and traffic conditions, and switch off the engine.
2. Restart the engine.
If the display message continues to be displayed, have the system checked. It is recommended you visit an INFINITI retailer for this
service.
The parking sensor system is faulty.
Have the system checked. It is recommended you visit an INFINITI retailer for this service.
[Park Assist Finished] The vehicle is parked. A warning tone also sounds.
The display message disappears automatically.
[ICC Off]
Intelligent Cruise Control has been deactivated (seeIntelligent Cruise Control (ICC) system (Full speed range) (if equipped)in the5.
Starting and drivingsection).
If it was not deactivated by the driver, a warning tone also sounds.
Instruments and controls2-47

•When cleaning the seat, never use gaso-
line, benzine, thinner, or any similar mate-
rials.
•If any malfunctions are found or the heated
seat does not operate, turn the switch off
and have the system checked. It is recom-
mended you visit an INFINITI retailer for this
service.
The front seats are warmed by built-in heaters.
The switches are located on the center console
and can be operated independently, for the
left-hand side seat and for the right-hand side
seat.
The three red indicator lights in the button
indicate the heating level you have selected The
system automatically switches from level 3 to
level 2 after approximately eight minutes The
system automatically switches from level 2 to
level 1 after approximately ten minutes. The
system automatically switches off approxi-
mately 20 minutes after it is set to level 1
1. Turn the ignition switch to the ON position.
NOTE
The seat heater can only be activated when
the ignition switch is in the ON position.2. Start the engine.
3. Select the heat range:
•To switch on: press button1repeatedly
until the desired heating level is set.
•To switch off: press button1repeatedly
until all the indicator lights turn off.
NOTE
If the battery voltage is too low, the seat heating
may switch off.
NIC2634
2-70Instruments and controls

•Recommendation for air distribution in win-
ter: select theandsettings.
Recommendation for air distribution in sum-
mer: select the
orandsettings.
•Only use theWindshield demistingfunc-
tion briefly until the windshield is clear again
•Only use air-recirculation mode briefly, e. g
if there are unpleasant outside odors or
when in a tunnel. The windows could other-
wise mist up as no fresh air is drawn into the
vehicle in air-recirculation mode
•If you change the settings of the climate
control system, the climate status display
appears for approximately three seconds at
the bottom of the screen in the central
display (see separate operating instruc-
tions). You will see the current settings of the
various climate control functions.
Switching air-conditioning system
on/off
Make sure the ignition switch is in the ON
position.
To switch on:turn control
5clockwise to the
desired position (except position0).
To switch off:turn control
5counter-clockwise
to position0.
Activating/deactivating the cooling
with air dehumidification function
If you deactivate theCooling with air dehumidi-
ficationfunction, the air inside the vehicle will
not be cooled. The air inside the vehicle will
also not be dehumidified. The windows can mist
up more quickly. Therefore, only deactivate the
Cooling with air dehumidificationfunction
briefly.
TheCooling with air dehumidificationfunction
is only available when the engine is running.
The air inside the vehicle is cooled and dehu-
midified according to the temperature selected.
Condensation may drip from the underside of
the vehicle when cooling mode is active. This is
normal and not a sign that there is a malfunc-
tion.
To activate
:
Press thebutton The indicator lamp in
thebutton lights up.
To deactivate
:
Press thebutton. The indicator lamp in
thebutton goes out. The cooling with air
dehumidification function has a delayed switch-
off feature.Problems with theCooling with air dehumidifi-
cationfunction
:
Problem:The indicator lamp in thebutton flashes three times or remains off. The
cooling with air dehumidification function can-
not be activated.
Cause and solution:The cooling with air dehu-
midification function has been deactivated due
to a malfunction. Have the system checked. It is
recommended you visit an INFINITI retailer for
this service.
Setting the temperature
You can set the temperature for the entire
vehicle. The set temperature is automatically
maintained at a constant level.
To increase or reduce the temperature: turn
control
1counterclockwise or clockwise. Only
change the temperature setting in small incre-
ments. Start at 70
oF (22oC).
Setting the air distribution
Directs the airflow through the demis-
ter ventilators.
Directs the airflow through the center
and side air ventilators.
Directs the airflow through the footwell
air ventilators.
Display screen, heater and air conditioner, and audio system4-45

•Use thefunction to adopt the tem-
perature settings on the driver’s side for the
front-passenger side as well. The indicator
lamp in the
button goes out.
•If you change the settings of the climate
control system, the climate status display
appears for approximately three seconds at
the bottom of the screen in the center display
(see separate operating instructions). You
will see the current settings of the various
climate control functions.
Idle Stop/Start function
During automatic engine switch-off, the Climate
control only operates at a reduced capacity. If
you require the full climate control output, you
can switch off the Idle Stop/Start function by
pressing the ECO button (seeIdle Stop/Start
System (if equipped)in the5. Starting and
drivingsection).
Switching automatic climate control
on/off
When the climate control is switched off, the air
supply and air circulation are also switched off.
The windows could mist up. Therefore, only
switch off climate control briefly.
Make sure the ignition switch is in the ON
position.To activate
:
Press thebutton The indicator lamp in
thebutton lights up. Airflow and air
distribution are set to automatic mode.
or
Press the
button. The indicator lamp in
thebutton goes out. The previous set-
tings are reactivated.
To deactivate
:
Press thebutton. The indicator lamp in
thebutton lights up.
NOTE
Automatic climate control: switch on climate
control primarily using the
button.
Activating/deactivating the cooling
with air dehumidification function
If you deactivate theCooling with air dehumidifi-
cationfunction, the air inside the vehicle will not
be cooled. The air inside the vehicle will also not
be dehumidified. The windows can mist up more
quickly. Therefore, only deactivate theCooling
with air dehumidificationfunction briefly.
TheCooling with air dehumidificationfunction
is only available when the engine is running.
The air inside the vehicle is cooled and dehu-
midified according to the temperature selected.Condensation may drip from the underside of
the vehicle when cooling mode is active. This is
normal and not a sign that there is a malfunc-
tion.
To activate
:
Press thebutton The indicator lamp in
thebutton lights up.
To deactivate
:
Press thebutton. The indicator lamp in
thebutton goes out. The cooling with air
dehumidification function has a delayed switch-
off feature.
Problems with theCooling with air dehumidifi-
cationfunction
:
Problem:The indicator lamp in thebutton flashes three times or remains off. The
cooling with air dehumidification function can-
not be activated.
Cause and solution:The cooling with air dehu-
midification function has been deactivated due
to a malfunction. Have the system checked. It is
recommended you visit an INFINITI retailer for
this service.
Display screen, heater and air conditioner, and audio system4-49

Activating air recirculation mode:
Make sure the ignition switch is in the ON
position.
Press the
button. The indicator light in
thebutton lights up.
Air-recirculation mode is activated automati-
cally at high outside temperatures or high
levels of pollution. When air-recirculation mode
is activated automatically, the indicator light in
the
button is not lit. Outside air is added
after about 30 minutes.
Deactivating air recirculation mode
:
Press thebutton. The indicator light in
thebutton goes out.
NOTE
Air-recirculation mode is deactivated automati-
cally:
•After approximately five minutes at outside
temperatures below approximately 45oF(7oC).
•After approximately five minutes if theCool-
ing with air dehumidificationfunction is
deactivated.
•After approximately 30 minutes at outside
temperatures above approximately 45oF(7oC) if the cooling with air dehumidification
function is activated.
SERVICING AIR CONDITIONER
WARNING
The air conditioner system contains refriger-
ant under high pressure. To avoid personal in-
jury, any air conditioner service should be
done only by an experienced technician with
the proper equipment.
The air conditioner system in your vehicle is
charged with a refrigerant designed with the
environment in mind.
This refrigerant will not harm the earth’s ozone
layer.
Special charging equipment and lubricant are
required when servicing your vehicle’s air con-
ditioner. Using improper refrigerants or lubri-
cants will cause severe damage to the air
conditioner system. (SeeAir conditioner sys-
tem refrigerant and oil recommendationsin the
9. Maintenance and Schedulessection.)
An INFINITI retailer will be able to service your
environmentally friendly air conditioner system.
Air conditioner filter
The air conditioner system is equipped with an
air conditioner filter. To make sure the air
conditioner heats, defogs, and ventilates effi-
ciently, replace the filter in accordance with the
specified maintenance intervals listed in the
separate maintenance booklet. It is recom-
mended you visit an INFINITI retailer for this
service.
The filter should be replaced if the air flow
decreases significantly or if windows fog up
easily when operating the heater or air condi-
tioner.
4-52Display screen, heater and air conditioner, and audio system