2017 INFINITI QX30 light

FRONT SEATS
Manual seat adjustment
Forward and backward:
Pull the lever1up and hold it while sliding the
seat forward or backward to the preferred posi-
tion. Release the lever to lock the seat in
position.
Seat cushion angle (if equipped)
:
Adjust the angles so that your thighs are lightly
supported. Turn handwheel
2forwards or
backwards.Seat lifter (if equipped)
:
Repeatedly pull up or push down the adjusting
lever
3, to adjust the seat height to the
desired position.
Seatback angle
:
Relieve the pressure on the seatback and turn
handwheel
4forwards or backwards.
The reclining feature allows the adjustment of
the seatback for occupants of different sizes to
help obtain the proper seat belt fit. (SeeSeat
beltslater in this section.)
The seatback may be reclined to allow occu-
pants to rest when the vehicle is parked.Lumbar support
:
The lumbar support feature provides lower back
support to the driver.
Push each side of the adjusting switch to adjust
the seat lumbar area until the desired position
is achieved.
1To raise the seatback contour
2To soften the seatback contour
3To lower the seatback contour
4To harden the seatback contour
NIC2605NIC2607
Safety — seats, seat belts and supplemental restraint system1-3

Removing and fitting the rear seat
head restraints/headrests
The rear head restraints/headrests on the outer
seats can be removed and refitted. For vehicles
with sports seats the rear head restraints/
headrests cannot be removed and refitted.
Fold the seatback slightly forward in order to
remove the head restraint/headrest.
•To remove: pull the head restraint/headrest
up to the stop.
Press release catch
1and pull the head
restraint/headrest out of the guides.
•To refit: insert the head restraint/headrest
so that the notches on the bar are on the left
when viewed in the direction of travel.
Push the head restraint/headrest down until
you hear it engage in position.
PRECAUTIONS ON SEAT BELT USAGE
If you are wearing your seat belt properly
adjusted, and you are sitting upright and well
back in your seat, your chances of being injured
or killed in an accident and/or the severity of
injury may be greatly reduced. INFINITI strongly
encourages you and all of your passengers to
buckle up every time you drive, even if your
seating position includes a supplemental air
bag.
Most U.S. states and Canadian provinces or ter-
ritories specify that seat belts be worn at all
times when a vehicle is being driven.
SEAT BELTS
Safety — seats, seat belts and supplemental restraint system1-11

•The seat belt should be properly adjusted
to a snug fit. Failure to do so may reduce the
effectiveness of the entire restraint system
and increase the chance or severity of injury
in an accident. Serious injury or death can
occur if the seat belt is not worn properly.
•Always route the shoulder belt over your
shoulder and across your chest. Never put
the belt behind your back, under your arm or
across your neck. The belt should be away
from your face and neck, but not falling off
your shoulder.
•Position the lap belt as low and snug as
possible AROUND THE HIPS, NOT THE
WAIST. A lap belt worn too high could in-
crease the risk of internal injuries in an ac-
cident.
•Be sure the seat belt tongue is securely
fastened to the proper buckle.
•Do not wear the seat belt inside out or
twisted. Doing so may reduce its effective-
ness.
•Do not allow more than one person to use
the same seat belt.
•Never carry more people in the vehicle than
there are seat belts.
•If the seat belt warning light glows continu-
ously while the ignition is turned ON with all
doors closed and all seat belts fastened, it
may indicate a malfunction in the system.
Have the system checked. It is recom-
mended that you visit an INFINITI retailer for
this service.
•No changes should be made to the seat belt
system. For example, do not modify the seat
belt, add material or install devices that
may change the seat belt routing or tension.
Doing so may affect the operation of the
seat belt system. Modifying or tampering
with the seat belt system may result in seri-
ous personal injury.
•Once a seat belt pretensioner has acti-
vated, they cannot be reused and must be
replaced together with the retractor. It is
recommended that you visit an INFINITI re-
tailer for this service.
•All seat belt assemblies, including retrac-
tors and attaching hardware, should be in-
spected after any collision. It is recom-
mended that you visit an INFINITI retailer for
this service. INFINITI recommends that all
seat belt assemblies in use during a colli-
sion be replaced unless the collision was
minor and the belts show no damage andcontinue to operate properly. Seat belt as-
semblies not in use during a collision
should also be inspected and replaced if
either damage or improper operation is
noted.
•All child restraints and attaching hardware
should be inspected after any collision. Al-
ways follow the restraint manufacturer’s in-
spection instructions and replacement rec-
ommendations. The child restraints should
be replaced if they are damaged.
PREGNANT WOMEN
INFINITI recommends that pregnant women use
seat belts. The seat belt should be worn snug,
and always position the lap belt as low as
possible around the hips, not the waist. Place
the shoulder belt over your shoulder and across
your chest. Never put the lap/shoulder belt over
your abdominal area. Contact your doctor for
specific recommendations.
INJURED PERSONS
INFINITI recommends that injured persons use
seat belts. Check with your doctor for specific
recommendations.
Safety — seats, seat belts and supplemental restraint system1-13

SEAT BELT WARNING LIGHT
The seat belt warning light reminds you to
fasten your seat belts. The light illuminates if
the engine is started, all doors are closed and
the driver’s and/or front passenger’s seat belt
is unfastened. It will remain illuminated until
the driver and/or front passenger fastens their
seat belt. A chime will sound once the vehicle is
in motion.
If the seat belt warning light flashes, together
with an intermittent warning tone, this means
that the driver or passenger has not fastened
their seat belt, and the speed of the vehicle is
exceeding 15 MPH (25 km/h).
For additional information, refer toWarning
lights, indicator lights and audible reminders
in the2. Instruments and controlssection.
THREE-POINT TYPE SEAT BELT WITH
RETRACTOR
WARNING
•Every person who drives or rides in this
vehicle should use a seat belt at all times.
Children should be in the rear seats and in
an appropriate restraint.
•Do not ride in a moving vehicle when the
seatback is reclined. This can be dangerous.
The shoulder belt will not be against your
body. In an accident, you could be thrown
into it and receive neck or other serious in-
juries. You could also slide under the lap
belt and receive serious internal injuries.
•For the most effective protection when the
vehicle is in motion, the seat should be up-
right. Always sit well back and upright in the
seat with both feet on the floor and adjust
the seat belt properly.
•Do not allow children to play with the seat
belts. Most seating positions are equipped
with Automatic Locking Retractor (ALR)
mode seat belts. If the seat belt becomes
wrapped around a child’s neck with the ALR
mode activated, the child can be seriously
injured or killed if the seat belt retracts and
becomes tight. This can occur even if thevehicle is parked. Unbuckle the seat belt to
release the child. If the seat belt cannot be
unbuckled or is already unbuckled, release
the child by cutting the seat belt with a
suitable tool (such as a knife or scissors) to
release the seat belt.
Fastening the seat belts
1. Adjust the seat. (SeeSeatsearlier in this
section.)
2. Slowly pull the seat belt out of the retractor
and insert the tongue into the buckle until
you hear and feel the latch engage.NIC2743
1-14Safety — seats, seat belts and supplemental restraint system

•The retractor is designed to lock during a
sudden stop or on impact. A slow pulling
motion permits the belt to move and al-
lows you some freedom of movement in
the seat.
•If the seat belt cannot be pulled from its
fully retracted position, firmly pull the belt
and release it. Then smoothly pull the belt
out of the retractor.
3. Position the lap belt portionlow and snug on
the hipsas shown4. Pull the shoulder belt portion toward the
retractor to take up extra slack. Be sure the
shoulder belt is routed over your shoulder
and across your chest.
The front passenger seat and the rear seating
positions three-point seat belts have two
modes of operation:
•Emergency Locking Retractor (ELR)
•Automatic Locking Retractor (ALR)
The ELR mode allows the seat belt to extend and
retract to allow the driver and passengers some
freedom of movement in the seat. The ELR locks
the seat belt when the vehicle slows down
rapidly or during certain impacts.The ALR mode (child restraint mode) locks the
seat belt for child restraint installation. When
the ALR mode is activated, the seat belt cannot
be extended again until the seat belt tongue is
detached from the buckle and fully retracted.
The seat belt returns to the ELR mode after the
seat belt fully retracts. For additional informa-
tion, refer toChild restraintslater in this
section. The ALR mode should be used only for
child restraint installation. During normal seat
belt use by an occupant, the ALR mode should
not be activated. If it is activated, it may cause
uncomfortable seat belt tension. It can also
change the operation of the front passenger air
bag. For additional information, refer toFront
passenger air bag and status lightin the1.
Safety — seats, seat belts and supplemental
restraint systemSafety — seats, seat belts and
supplemental restraint systemsection.WARNING
When fastening the seat belts, be certain that
the seatbacks are completely secured in the
latched position. If they are not completely
secured, passengers may be injured in an acci-
dent or sudden stop.
SSS0292ZSSS0290Z
Safety — seats, seat belts and supplemental restraint system1-15

Outboard seating positions with removable
head restraints/headrests:
1. If necessary, raise or remove the head
restraint/headrest and store it in a secure
place. Be sure to reinstall the head restraint/
headrest when the child restraint is re-
moved. For additional information about
head restraint/headrest adjustment, removal
and installation, refer toHead
restraints/Headrestsin the1. Safety —
seats, seat belts and supplemental restraint
systemsection.
2. Position the top tether strap
1over the
seatback.
3. Secure the tether strap to the tether anchor
point
2on the seatback behind the child
restraint.
4. Tighten the tether strap according to the
manufacturer’s instructions to remove any
slack.Outboard seating positions with fixed head
restraints/headrests
:
1. If the child restraint has a single tether
strap, route the strap
1over the top of the
outer head restraint/headrest. If the child
restraint has two tether straps, route them
round each side of the outer head restraint/
headrest.
2. Secure the tether strap to the tether anchor
point
2on the seatback behind the child
restraint.
3. Tighten the tether strap according to the
manufacturer’s instructions to remove any
slack.
If you have any questions when installing a
top tether strap, it is recommended that you
visit an INFINITI retailer for this service.
FORWARD-FACING CHILD RESTRAINT
INSTALLATION USING THE SEAT BELTS
WARNING
The three-point seat belt with Automatic Lock-
ing Retractor (ALR) must be used when install-
ing a child restraint. Failure to use the ALR
mode will result in the child restraint not being
properly secured. The restraint could tip over
or be loose and cause injury to a child in a
sudden stop or collision. Also, it can change
the operation of the front passenger air bag.
For additional information, refer toFront pas-
senger air bag and status lightin the1. Safety
— seats, seat belts and supplemental restraint
systemsection.
For additional information, refer to all Warnings
and Cautions in theChild safetyin the1.
Safety — seats, seat belts and supplemental
restraint systemSafety — seats, seat belts and
supplemental restraint systemsection and
Child restraintsin the1. Safety — seats, seat
belts and supplemental restraint systemsec-
tion before installing a child restraint.
Safety — seats, seat belts and supplemental restraint system1-31

6. Remove any additional slack from the seat
belt; press downward and rearward firmly in
the center of the child restraint with your
knee to compress the vehicle seat cushion
and seatback while pulling up on the seat
belt.
7. Tighten the tether strap according to the
manufacturer’s instructions to remove any
slack.8. After attaching the child restraint, test it
before you place the child in it. Push it from
side to side while holding the child restraint
near the seat belt path. The child restraint
should not move more than 1 inch (25 mm),
from side to side. Try to tug it forward and
check to see if the belt holds the restraint in
place. If the restraint is not secure, tighten
the seat belt as necessary, or put the re-
straint in another seat and test it again. You
may need to try a different child restraint.
Not all child restraints fit in all types of
vehicles.
9. Check to make sure the child restraint is
properly secured prior to each use. If the
seat belt is not locked, repeat steps 2
through 8.10. If the child restraint is installed in the front
passenger seat, place the ignition switch in
the ON position. The front passenger air
bag status OFF light should illuminate. If
this light is not illuminated refer toFront
passenger air bag and status lightin the
1. Safety — seats, seat belts and supple-
mental restraint systemsection.Move the
child restraint to another seating position.
Have the system checked. It is recom-
mended you visit an INFINITI retailer for this
service. After the child restraint is removed
and the seat belt is fully retracted, the ALR
mode (child restraint mode) is canceled.
WRS0681ZForward-facing — step 6WRS0698ZForward-facing — step 8SSS0676ZForward-facing — step 10
1-34Safety — seats, seat belts and supplemental restraint system

If the indicator
lamp does NOT light continuously when a
child restraint is installed on the front
passenger seat, the seat may not be used
for a child restraint. Move the child re-
straint to another position. See
Troubleshootinglater in this section. Have
the system checked. It is recommended you
visit an INFINITI retailer for this service.
Installing top tether strap
WARNING
Child restraint anchorages are designed to
withstand only those loads imposed by cor-
rectly fitted child restraints. Under no circum-
stances are they to be used to attach adult seat
belts, or other items or equipment to the ve-
hicle. Doing so could damage the child re-
straint anchorages. The child restraint will not
be properly installed using the damaged an-
chorage, and a child could be seriously injured
or killed in a collision.
The child restraint top tether strap must be
used when installing the child restraint with
seat belts.
First, secure the child restraint with the seat
belt.Outboard seating positions with removable
head restraints/headrests:
1. If necessary raise or remove the head
restraint/headrest and store it in a secure
place. Be sure to reinstall the head restraint/
headrest when the child restraint is re-
moved. For additional information about
head restraint/headrest adjustment, removal
and installation, refer toHead
restraints/Headrestsin the1. Safety —
seats, seat belts and supplemental restraint
systemsection.
2. Position the top tether strap
1over the
seatback.
3. Secure the tether strap to the tether anchor
point
2on the seatback behind the child
restraint.4. Tighten the tether strap according to the
manufacturer’s instructions to remove any
slack.
Outboard seating positions with fixed head
restraints/headrests
:
1. If the child restraint has a single tether
strap, route the strap
1over the top of the
outer head restraint/headrest. If the child
restraint has two tether straps, route them
round each side of the outer head restraint/
headrest.
2. Secure the tether strap to the tether anchor
point
2on the seatback behind the child
restraint.
3. Tighten the tether strap according to the
manufacturer’s instructions to remove any
slack.
NIC2848Rear seat - Type ANIC2903Rear seat - Type B
Safety — seats, seat belts and supplemental restraint system1-35