2017 INFINITI QX30 start stop button

2. Press theorbutton to select
[Convenience] submenu.
3. Press to confirm.
4. Press the
orbutton to select
the [Fold Mirrors in when Locking] function.
If the [Fold Mirrors in when Locking] function
is activated, the vehicle’s exterior mirror is
shown in orange in the vehicle information
display.
5. Press the button to save the setting.
Resetting to factory settings
1. Press theorbutton on the
steering wheel to select the [Settings] menu.
2. Press the
orbutton to select
[Factory Setting] submenu.
3. Press to confirm.
The [Reset All Settings?] message appears.
4. Press the
orbutton to select
[No] or [Yes].
5. Press the button to confirm the selec-
tion.
If you have selected [Yes], the vehicle infor-
mation display shows a confirmation mes-
sage.For safety reasons, not all functions are reset:
the [Limit Speed (Winter Tires)] function in
permanent speed limiter can only be set in the
[Vehicle] submenu.
If you want to reset the Daytime driving lights
function in the Lights submenu, you must
switch the ignition switch to the ACC position.
DISPLAY MESSAGES
Display messages appear in the vehicle infor-
mation display.
Display messages with graphic symbols are
simplified in the Owner’s Manual and may differ
from the symbols in the vehicle information
display.
Certain display messages are accompanied by
an audible warning tone or a continuous tone.
When the ignition is switched off, all display
messages are deleted apart from some high-
priority display messages. Once the causes of
the high-priority display messages have been
rectified, these display messages are deleted
as well.
When you stop and park the vehicle, please
observe the notes on parking (seeParkingin
the5. Starting and drivingsection).
Hiding display messages
Press the orbutton to hide the
display message. The display message is hid-
den.
The vehicle information display shows high-
priority display messages in red. Some high-
priority display messages cannot be hidden.
The vehicle information display shows these
messages continuously until the causes for the
messages have been remedied.
Message memory
The vehicle information display saves certain
messages in the message memory. You can call
up these display messages:
1. Press the
orbutton on the
steering wheel to select the [Service] menu.
If there are display messages, the vehicle
information display shows [2 messages], for
example.
2. Press the
orbutton to select
the entry, e.g. [2 messages].
3. Press to confirm.
4. Press the
orbutton to scroll
through the display messages.
Instruments and controls2-29

Message Possible causes/consequences and solutions
[Inoperative See Operator’s
Manual]EBD (electronic brake force distribution) ABS (Anti-Lock Braking System), BAS (Brake Assist System), VDC (Vehicle Dynamic Contro), and
hill start assist are not available due to a malfunction.
Forward Emergency Braking (FEB) may also have failed.
A warning tone sounds.
In addition, the
,andwarning lights may light up in the combination meter.
WARNING
The brake system continues to function normally, but without the functions listed above. The front and rear wheels could therefore lock if
you brake hard, for example.
The steering and braking characteristics may be severely affected. The braking distance may increase in an emergency braking situation.
If VDC is not operational, VDC is unable to stabilize the vehicle. There is an increased danger of skidding and risk of an accident.
Drive on carefully and have the system checked immediately. It is recommended you visit an INFINITI retailer for this service.
[Turn On The Ignition to Re-
lease the Parking Brake]The redindicator light lights up.
You attempted to release the electric parking brake while the ignition was switched off.
Key: turn the key to the ON position in the ignition switch
[Please Release Parking
Brake]The redindicator light flashes and a warning tone sounds. A condition for automatic release of the electric parking brake is not
fulfilled (seeApplying automatically (vehicles with automatic transmission)in the5. Starting and drivingsection).
You are driving with the electric parking brake applied.
Release the electric parking brake manually.
The red
indicator light flashes and a warning tone sounds.
You are making an emergency stop using the electric parking brake (seeEmergency brakingin the5. Starting and drivingsection)
[Parking Brake See Opera-
tor’s Manual]The yellowwarning light lights up.
The electric parking brake is malfunctioning.
To apply:
1. Switch the ignition off.
2. Press the electric parking brake handle for at least ten seconds.
3. Press the P (Park) button.
4. Have the system checked. It is recommended you consult an INFINITI retailer.
2-32Instruments and controls

•To interrupt automatic operation: press/pull
the corresponding switch again.
NOTE
•If you press/pull the switch beyond the point
of resistance, automatic operation is started
in the corresponding direction. You can stop
automatic operation by pressing/pulling
again.
•You can continue to operate the side win-
dows after switching off the engine or remov-
ing the key. This function remains active for
five minutes or until the driver’s or front-
passenger door is opened.
•The side windows cannot be operated from
the rear when the override feature for the
side windows is activated.Locking rear side windows
:
To enable/disable the override feature for the
rear side windows, press button
2. If indicator
lamp
1is lit, operation of the rear side win-
dows is disabled. Operation is only possible
using the switches in the driver’s door. If indi-
cator lamp
1is off, operation is possible using
the switches in the rear compartment.
Passenger’s window switch
The passenger’s switch can control its corre-
sponding window.
Convenience opening feature
For vehicles with Intelligent key:you can venti-
late the vehicle before you start driving. The key
can also be used to carry out the following
functions simultaneously:
•Unlock the vehicle
•Open the side windows
NOTE
The convenience opening feature can only be
operated using the key.
The key must be in close proximity to the ve-
hicle.
NIC2716NIC2640
2-72Instruments and controls

OPENING FUEL-FILLER DOOR
To open the fuel-filler door, unlock it using one
of the following operations, then push the right
side of the door
1.
•Push the door handle request switch with
the Intelligent Key carried with you.
•Push the “UNLOCK”button on the
Intelligent Key.
•Push the power door lock switch to the
“UNLOCK”position.
To close the fuel-filler door, close the door until
it securely latches. To lock the fuel filler door,
lock the vehicle using the intelligent key.
FUEL-FILLER CAP
Turn the fuel-filler cap counterclockwise to re-
move. To tighten, turn the cap clockwise until a
single click is heard.
Put the fuel-filler cap on the cap holder
2while refueling.
WARNING
•Gasoline is extremely flammable and
highly explosive under certain conditions.
You could be burned or seriously injured if it
is misused or mishandled. Always stop the
engine and do not smoke or allow open
flames or sparks near the vehicle when re-
fueling.
•Do not attempt to top off the fuel tank after
the fuel pump nozzle shuts off automati-
cally. Continued refueling may cause fuel
overflow, resulting in fuel spray and possi-
bly a fire.
•Use only an original equipment type fuel-
filler cap as a replacement. It has a built-in
safety valve needed for proper operation of
the fuel system and emission control sys-
tem. An incorrect cap can result in a serious
malfunction and possible injury.
•Never pour fuel into the throttle body to
attempt to start your vehicle.
•Do not fill a portable fuel container in the
vehicle or trailer. Static electricity can cause
an explosion of flammable liquid, vapor or
gas in any vehicle or trailer. To reduce the
risk of serious injury or death when filling
portable fuel containers:
–Always place the container on the
ground when filling.
–Do not use electronic devices when fill-
ing.
–Keep the pump nozzle in contact with
the container while you are filling it.
–Use only approved portable fuel con-
tainers for flammable liquid.
CAUTION
•Do not use E-15 or E-85 fuel in your vehicle.
For additional information, refer toFuel
Recommendationin theTechnical and
consumer informationsection of this
manual.
•If fuel is spilled on the vehicle body, flush it
away with water to avoid paint damage.
NPA1482
FUEL-FILLER DOOR
Pre-driving checks and adjustments3-15

Air recirculation mode
You can deactivate the flow of fresh air if
unpleasant odors are entering the vehicle from
outside. The air already inside the vehicle will
then be recirculated.
If you activate air-recirculation mode, the win-
dows can mist up more quickly, in particular at
low temperatures. Only use air recirculation
mode briefly to prevent the windows misting
up.
Activating air recirculation mode
:
Make sure the ignition switch is in the ON
position.
Press the
button. The indicator light in
thebutton lights up.Deactivating air recirculation mode
:
Press thebutton. The indicator light in
thebutton goes out.
NOTE
Air-recirculation mode is deactivated automati-
cally:
•After approximately five minutes at outside
temperatures below approximately 45oF
(7oC).
•After approximately five minutes if theCool-
ing with air dehumidificationfunction is
deactivated.
•After approximately 30 minutes at outside
temperatures above approximately 45oF
(7oC) if the cooling with air dehumidification
function is activated.
Idle Stop/Start function
During automatic engine switch-off, the Climate
control only operates at a reduced capacity. If
you require the full climate control output, you
can switch off the Idle Stop/Start function by
pressing the ECO button (seeIdle Stop/Start
System (if equipped)in the5. Starting and
drivingsection).
Display screen, heater and air conditioner, and audio system4-47

•Use thefunction to adopt the tem-
perature settings on the driver’s side for the
front-passenger side as well. The indicator
lamp in the
button goes out.
•If you change the settings of the climate
control system, the climate status display
appears for approximately three seconds at
the bottom of the screen in the center display
(see separate operating instructions). You
will see the current settings of the various
climate control functions.
Idle Stop/Start function
During automatic engine switch-off, the Climate
control only operates at a reduced capacity. If
you require the full climate control output, you
can switch off the Idle Stop/Start function by
pressing the ECO button (seeIdle Stop/Start
System (if equipped)in the5. Starting and
drivingsection).
Switching automatic climate control
on/off
When the climate control is switched off, the air
supply and air circulation are also switched off.
The windows could mist up. Therefore, only
switch off climate control briefly.
Make sure the ignition switch is in the ON
position.To activate
:
Press thebutton The indicator lamp in
thebutton lights up. Airflow and air
distribution are set to automatic mode.
or
Press the
button. The indicator lamp in
thebutton goes out. The previous set-
tings are reactivated.
To deactivate
:
Press thebutton. The indicator lamp in
thebutton lights up.
NOTE
Automatic climate control: switch on climate
control primarily using the
button.
Activating/deactivating the cooling
with air dehumidification function
If you deactivate theCooling with air dehumidifi-
cationfunction, the air inside the vehicle will not
be cooled. The air inside the vehicle will also not
be dehumidified. The windows can mist up more
quickly. Therefore, only deactivate theCooling
with air dehumidificationfunction briefly.
TheCooling with air dehumidificationfunction
is only available when the engine is running.
The air inside the vehicle is cooled and dehu-
midified according to the temperature selected.Condensation may drip from the underside of
the vehicle when cooling mode is active. This is
normal and not a sign that there is a malfunc-
tion.
To activate
:
Press thebutton The indicator lamp in
thebutton lights up.
To deactivate
:
Press thebutton. The indicator lamp in
thebutton goes out. The cooling with air
dehumidification function has a delayed switch-
off feature.
Problems with theCooling with air dehumidifi-
cationfunction
:
Problem:The indicator lamp in thebutton flashes three times or remains off. The
cooling with air dehumidification function can-
not be activated.
Cause and solution:The cooling with air dehu-
midification function has been deactivated due
to a malfunction. Have the system checked. It is
recommended you visit an INFINITI retailer for
this service.
Display screen, heater and air conditioner, and audio system4-49

For CDs without compressed audio files:
Mode Screen display
Disc Repeat
Disc
1 Track Repeat
1 Track
Disc Random
Disc
For CDs with compressed audio files:
Mode Screen display
Disc Repeat
Disc
1 Folder Repeat
1 Folder
1 Track Repeat
1 Track
Disc Random
Disc
1 Folder Random
1 Folder
CD player operation
Loading:
Insert the CD into the slot with the label side
facing up. The CD will be guided automatically
into the slot and starts playing.
After loading the CD, the CD screen will appear
on the display.
Activation and playing
:
The CD mode can be selected from the source
list or by pushing thebutton with a CD
loaded to play the CD.
For details, seeSelecting audio sourceearlier
in this section andMain audio buttonsearlier
in this section.
If the system has been turned off while the CD
was playing, pushing >will start
the Audio system set to the CD screen.
Selecting track/folder
:
Touch [Track] or [Folder] in the CD menu and
select a preferred track or folder from the list.
Push to move to the next or
previous track.For CDs with compressed audio files, push
to move to the next or
previous folder.
For details, seeMain audio buttonsearlier in
this section.
Fast-forwarding/rewinding
:
Push and holdto fast-
forward or rewind the track. Release •CAT•TRACK> to play the track at normal speed.
Scanning
:
Touch [Scan] on the display to scan the tracks in
the CD. While scanning, the CD will play the first
10 seconds of each track and move on to the
next track. Pushing [Scan] again within the 10
seconds will stop scanning.
Changing play mode
:
Touch [Play Mode] or the play mode icon ([]or[]) to select the play mode.
Ejecting CD
:
Push<>to eject the CD. If the CD is
ejected and left unremoved, it will be reloaded
into the slot to protect the CD.
4-72Display screen, heater and air conditioner, and audio system

STARTING PROCEDURE WITH THE KEY
0OFF position
1ACC position
2ON position
3START position
1. Apply the parking brake.
2. Shift the transmission to position P (Park)
by pressing the

button.
The transmission position indicator in the
vehicle information display shows

When the transmission is in position N (Neu-
tral), you can also start the engine with the
brake pedal depressed.The starter is designed not to operate if the shift
lever is in any of the driving positions.
3. Turn the key to the START position
3in the
ignition lock and release it as soon as the
engine is running.
If the engine is very hard to start because it is
flooded, depress the accelerator pedal all the
way to the floor and hold it. Turn the ignition
switch to the START position to start cranking
the engine. After 5 or 6 seconds, stop cranking
by turning the ignition switch to OFF. After
cranking the engine, release the accelerator
pedal. Crank the engine with your foot off the
accelerator pedal by depressing the brake
pedal and turning the ignition switch to start
the engine. If the engine starts, but fails to run,
repeat the above procedure.
CAUTION
Do not operate the starter for more than 15
seconds at a time. If the engine does not start,
turn the ignition key to the OFF position and
wait 10 seconds before cranking again, other-
wise the starter could be damaged.
4.Warm-up
Allow the engine to idle for at least 30
seconds after starting. Do not race the en-
gine while warming it up. Drive at moderate
speed for a short distance first, especially in
cold weather. In cold weather, keep the
engine running for a minimum of2-3
minutes before shutting it off. Starting and
stopping the engine over a short period of
time may make the vehicle more difficult to
start.
5. To stop the engine, Shift the transmission to
position P (Park) by pressing the

button.
and turn the ignition switch to the OFF
position.
NPA1483
STARTING ENGINE
5-16Starting and driving