2017 Hyundai Sonata Plug-in Hybrid trunk

7-69
7
Maintenance
Instrument panel fuse (Plug-in hybrid)
Fuse rating Fuse Name Protected Component
SAFETY POWERWINDOW LH 25A Driver Safety Power Window Module
P/SEAT PASS 30A Passenger Seat Manual Switch
P/WDW LH 20A Power Window Main Switch, Rear Power Window Module LH
P/WDW RH 25A Power Window Main Switch, Rear Power Window Module RH, Passenger Door Module,
Passenger Power Window Switch
DR LOCK 20A Door Lock Relay, Door Unlock Relay, ICM Relay Box (Two Turn Unlock Relay)
S/HEATER FRT 25A Front Air Ventilation Seat Module, Front Seat Warmer Module
BRAKE
SWITCH 10A Stop Lamp Switch, Smart Key Control Module
8MODULE 7.5A BCM, Smart Key Control Module
SAFETY POWER WINDOW RH 25A Passenger Safety Power Window Module
BATTERY
MANAGEMENT 10A BMS Control Module
SMART KEY 15A Smart Key Control Module
TRUNK 10A Trunk Lid Relay, ICM Relay Box (Fuel Filler Relay)
7MODULE 10A Driver/Passenger Door Module, Rear Parking Assist Sensor, Digital Clock,
Electric Parking Brake Module, Blind Spot Detection Radar LH/RH
INTERIOR LAMP 10A Glove Box Lamp, Front Vanity Lamp Switch LH/RH, Room Lamp, Overhead Console Lamp,
Rear Personal Lamp LH/RH, Trunk Room Lamp, Driver/Passenger Door Lamp
2MEMORY 7.5A Not Used

7-71
7
Maintenance
Fuse rating Fuse Name Protected Component
6MODULE10A Multipurpose Check Connector, TMU Unit, A/C Control Module, Vess Unit, Electro Chromic Mirror,
Rear Seat Warmer Module, A/T Shift Lever IND., Front Air Ventilation Seat Module,
Front Seat Warmer Module, Driver IMS Module, ICM Relay Box (IG3 #1 Relay)
AMP 25A AMP (JBL/MOBIS)
HTD STRG 15A BCM
5MODULE 10A Front Console, Switch Fuel Filler Door & Trunk Lid Switch, Active Air Flap Tire Pressure Monitoring Module,
Lane Departure Warning Unit, Smart Cruise Control Unit
IG1 25A PCB Block (Fuse - TCU 2/HEV ECU 2/OPCU 2/AHB 3)
WASHER 15A Multifunction Switch (Wiper Low & Washer Switch)
POWER OUTLET 20A Cigarette Lighter
GATEWAY 10A Gateway
A/BAG 15A SRS Control Module, Occupant Detection Sensor
IG3 15A ICM Relay Box (IG3 #1/2/3 Relay)
START 7.5A Transaxle Range Switch, HPCU
Instrument panel fuse (Plug-in hybrid)

7-77
7
Maintenance
Engine compartment main fuse panel (Plug-in hybrid)
Fuse NameFuse rating Protected Component
MULTI FUSE(TYPE A)
IG2 30A PCB Block (IG2 Relay)
BLOWER 40A Blower Relay 2AHB 40A Integrated Brake Actuation Unit, Multipurpose Check Connector 1 AHB 40A Integrated Brake Actuation Unit, Multipurpose Check Connector
REAR
HEATED 50A Rear Heated Relay
3 B+ 50A IGPM (IPS2 (4CH), IPS3 (4CH), Fuse - STOP LAMP/MODULE 1)
5 B+ 50A PCM Block (Fuse - WIPER/HORN/BATTERY C/FAN/AMS/TCU 1/ECU 2/FUEL PUMP,
Engine Control Relay)
EEWP 60A Electric Water Pump
MDPS 80A MDPS Unit
MULTI FUSE (TYPE B)
IG1 40A PCB Block (IG1 Relay) 3 POWER
OUTLET 40A Power Outlet Relay
2 PTC
HEATER 50A PTC Heater 2 Relay
1 PTC
HEATER50A PTC Heater 1 Relay
2 B+ 50A IGPM (IPS1 (4CH), IPS4 (4CH), IPS5 (4CH), Fuse - IG3/AMP)
1 B+60A IGPM (Fuse - P/SEAT DRV/P/SEAT PASS/S/HEATER RR/SUNROOF 1/
SUNROOF 2/SAFETY POWER WINDOW LH/ SAFETY POWER WINDOW RH/TRUNK,
Power Window Relay)
COOLING FAN 60A Cooling Fan Relay

7-80
Maintenance
L
LI
IG
G H
H T
T
B
B U
U L
LB
B S
S
Consult an authorized HYUNDAI
dealer to replace most vehicle light
bulbs. It is difficult to replace vehicle
light bulbs because other parts of the
vehicle must be removed before you
can get to the bulb. This is especially
true for removing the headlamp
assembly to get to the bulb(s).
Removing/installing the headlamp
assembly can result in damage to
the vehicle.Information
After heavy driving, rain or washing,
headlamp and trunk lenses could
appear frosty. This condition is caused
by the temperature difference
between the lamp inside and the out-
side temperature. This is similar to the
condensation on your windows inside
your vehicle during the rain and does-
n’t indicate a problem with your vehi-
cle. If the water leaks into the lamp
bulb circuitry, have your vehicle
checked by an authorized HYUNDAI
dealer.
i
Prior to replacing a lamp,
depress the foot brake, move
the shift lever into P (Park)
apply the parking brake, place
the igntion switch to the
LOCK/OFF position, and take
the key with you when leaving
the vehicle to avoid sudden
movement of the vehicle and
to prevent possible electric
shock.
Be aware the bulbs may be hot
and may burn your fingers.
WARNING

7-87
7
Maintenance
Rear combination light bulb
replacement
Type A
(1) Stop/Tail lamp
(2) Turn signal lamp
(3) Tail lamp
(4) Side marker lamp
Stop/Tail lamp and Turn signal lamp
1. Open the trunk lid.
2. Remove the service cover by turn-ing the lock counterclockwise and
then pulling it out. 3. Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
4. Remove the bulb from the socket by pressing it in and rotating it
counterclockwise until the tabs on
the bulb align with the slots in the
socket. Pull the bulb out of the
socket.
5. Install a new bulb by inserting it into the socket and rotating it until
it locks into place.
OLF074062
OLFH074019
OLFH074026LE
Stop/Tail lamp
Turn Signal lamp

7-88
Maintenance
6. Install the socket in the assembly by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
Tail lamp
1. Open the trunk.
2. Loosen the retaining screw of thetrunk lid cover and then remove
the cover.
3. Disconnect the connector and then remove the screws by turning
the screws counterclockwise. 4. Remove the bulb by pulling it
straight out.
5. Install a new bulb by inserting it into the socket and rotating it until
it locks into place.
6. Install the socket into the assem- bly by aligning the tabs on the
socket with the slots in the assem-
bly. Push the socket into the
assembly and turn the socket
clockwise.
7. Reinstall the trunk lid cover by pushing in the screw.
OLFH074026LOLFH074064
Tail lamp

7-90
Maintenance
Turn signal lamp
1. Open the trunk lid.
2. Remove the service cover by turn-ing the lock counterclockwise and
then pulling it out. 3. Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
4. Remove the bulb from the socket by pressing it in and rotating it
counterclockwise until the tabs on
the bulb align with the slots in the
socket. Pull the bulb out of the
socket.
5. Install a new bulb by inserting it into the socket and rotating it until
it locks into place. 6. Install the socket in the assembly
by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
OLF074062OLFH074027
Turn signal lamp

7-93
7
Maintenance
1. Using a flat-head screwdriver,gently pry the lens from the interi-
or light housing.
2. Remove the bulb by pulling it straight out.
3. Install a new bulb in the socket.
4. Align the lens tabs with the interi- or light housing notches and snap
the lens into place.
If the lamps do not operating, have
the vehicle checked by an authorized
HYUNDAI dealer.
Use care not to dirty or damage
lenses, lens tabs, and plastic
housings.
NOTICE
■ Map lamp - without sunroof
OLF074081N
OLF074082N
■Vanity mirror lamp
■Trunk room lamp
OLF074069
OLF074056
■ Room lamp - without sunroof
Map lamp, Room lamp, Vanity mirror lamp and Luggage room lamp