2017 HYUNDAI I20 hood open

6
"!!" " " !
"#!"! #! "#
1. Door lock\bunlock button ............514
2. Outside rearview mirror foldingswitch*........................................5\f5
\f. Outside rearview mirror control switch*........................................5\f4
4. Power window switches ............520
5. Power window lock switch ........52\f
6. Headlight leveling device*..........585
7. Instrument panel illumination control switch*............................5\f7
8. Fuel filler door opener* ..............527
9. Fuse
box.................\4..................\4.96 2
10. Steering wheel ........................5\f0
11. Seat ..........................................42
12. Clutch pedal ............................720
1\f. Brake pedal..............................7\f0
14. Accelerator pedal
15. Hood release lever ..................525
* : if equipped
OIB01400\fThe actual shape may differ from the illustration.

)'
#10*30-30.2+3%.,/3(21+2"1,/2*3!-$&3
RRemote key (if equipped)Your HYUNDAI uses a remote key,
which you can use to lock or unlock
a door (and tailgate) and even start
the engine.
1. Door Lock
2. Door Unlock
3. Tailgate Unlock
LockingTo lock :
1. Close all doors, engine hood and
tailgate.
2. Press the Door Lock button (1) on the remote key.
3. The doors will lock. The hazard warning lights will blink once.
4. Make sure the doors are locked by checking the position of the door
lock button inside the vehicle.
UnlockingTo unlock:
1. Press the Door Unlock button (2)on the remote key.
2. The doors will unlock. The hazard warning lights will blink two times.
Information
After unlocking the doors, the doors
will lock automatically after 30 sec-
onds unless a door is opened.i
$

+(('#&"*+'
%+
OIB034040
Do not leave the keys in your vehi-
cle with unsupervised children.
Unattended children could place
the key in the ignition switch and
may operate power windows or
other controls, or even make the
vehicle move, which could result in
serious injury or death.
WARNING

)')
#10*30-30.2+3%.,/3(21+2"1,/2*3!-$&3
OOpening the hood 1. Make sure the shift lever is in P
(Park, for Continuously Variable
Transaxle vehicle) or first gear or
R (Reverse, for Manual Transaxle
vehicle) and set the parking brake.
2. Pull the release lever to unlatch the hood. The hood should pop
open slightly. 3. Go to the front of the vehicle, raise
the hood slightly, push the second-
ary latch up (1) inside of the hood
center and lift the hood (2). 4. Pull out the support rod.
5. Hold the hood opened with the
support rod.&& 
OIB047050
OIB044047
OIB044052
The support rod must be inserted
completely into the hole provided
whenever you inspect the engine
compartment. This will prevent the
hood from falling and possibly
injuring you.
WARNING

)'#10*30-30.2+3%.,/3(21+2"1,/2*3!-$&3
CC losing the hood1. Before closing the hood, check the
following:
• All filler caps in engine compart- ment must be correctly installed.
• Gloves, rags or any other com- bustible material must be removed
from the engine compartment.
2. Return the support rod to its clip to prevent it from rattling.
3. Lower the hood halfway (lifted approximately 30cm from the
closed position) and push down to
securely lock in place. Then dou-
ble check to be sure the hood is
secure.
•
Before closing the hood, ensure
that all obstructions are
removed from the hood opening.
Closing the hood with an
obstruction present in the hood
opening may result in property
damage or severe personal
injury.
•
Do not leave gloves, rags or any
other combustible material in the
engine compartment. Doing so
may cause a heat-induced fire.
•
Do not move the vehicle with the
hood raised. The view will be
blocked and the hood could fall
or be damaged.
WARNING
Always double check to be surethat the hood is firmly latched
before driving away. Check there
is no hood open warning light or
message displayed on the instru-
ment cluster. Driving with the hood
opened may cause a total loss of
visibility, which might result in an
accident.
WARNING

If your temperature gauge indicates
overheating, you experience a loss
of power, or hear loud pinging or
knocking, the engine may be over-
heating. If this happens, you should:
1.Pull off the road and stop as soonas it is safe to do so.
2.Place the shift lever in P (Park, for Continuously Variable Transaxle
vehicle) or neutral (for Manual
Transaxle vehicle) and set the
parking brake. If the air condition-
ing is ON, turn it OFF.
3.If engine coolant is running out under the vehicle or steam is com-
ing out from the hood, stop the
engine. Do not open the hood until
the coolant has stopped running or
the steaming has stopped. If there
is no visible loss of engine coolant
and no steam, leave the engine
running and check to be sure the
engine cooling fan is operating. If
the fan is not running, turn the
engine off. 4.Check for coolant leaking from the
radiator, hoses or under the vehi-
cle. (If the air conditioning had
been in use, it is normal for cold
water to be draining from it when
you stop.)
5.If engine coolant is leaking out, stop the engine immediately and
we recommend that you call an
authorized HYUNDAI dealer for
assistance.$$ !%%#$#%% %"!!!$#'#"'"' %'$%'&&&%
While the engine is run-
ning, keep hands,
clothing and tools away
from the moving parts
such as the cool ing fan
and drive belt to pre-
vent serious injury.WARNING
NEVER remove the
radiator cap or the
drain plug while the
engine and radiator are
hot. Hot coolant and
ste am may blow out under pres-
sure, causing serious injury.
Turn the engine off and wait until
the engine cools down. Use
extreme care when removing the
radiator cap. Wrap a thick towel
around it, and turn it c ounterclock-
wise slowly to the first stop. Step
back while the pressure is
released from the cooling sy stem.
When you are sure all the pres-
sure has been released, press
down on the cap, using a thick
towel, and continue turning coun-
terclockwise to remove it.WARNING

1.$1
,204/3424-3
HHeadlight (Low/High)1. Open the hood.
2. Remove the headlight bulb cover
by turning it counterclockwise.
3. Disconnect the headlight bulb socket-connector. 4. Unsnap the headlight bulb retain-
ing wire by depressing the end
and pushing it upward.
5. Remove the bulb from the head- light assembly.
6. Install a new headlight bulb and snap the headlight bulb retaining
wire into position by aligning the
wire with the groove on the bulb.
7. Connect the headlight bulb socket connector.
8. Install the headlight bulb cover by turning it clockwise.
Information
- Bi-Function projection
headlight
This headlight is bi-function type that
switches the low beam to high or the
high beam to low using solenoid sys-
tem. So, the moving sound may be
heard when the headlight switches the
low beam to high or the high beam to
low and it does not indicate malfunc-
tion of the headlight.
Turn signal light1. Remove the turn signal light bulb cover by turning it counterclock-
wise.
2. Remove the socket from the assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
3. Insert a new bulb by inserting it into the socket and rotating it until
it locks into place.
4. Install the socket in the assembly by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
5. Install the turn signal light bulb cover by turning it clockwise.
i
OIB074048
Turn signal light
Parking
(Position) light
Headlight
■ MFR (Multi Focus Reflector) Headlight
OIB075061
Turn signal light
Headlight
■Bi-Function Projection Headlight

1.',204/3424-3LLow Beam Assist-Static Light1. Open the hood.
2. Remove the Low Beam Assist-
Static Light bulb cover by turning it
counterclockwise.
3. Disconnect the Low Beam Assist- Static Light bulb socket-connector.
4. Unsnap the Low Beam Assist- Static Light bulb retaining wire by
depressing the end and pushing it
upward.
5. Remove the bulb from the Low Beam Assist-Static Light assem-
bly. 6. Install a new Low Beam Assist-
Static Light bulb and snap the Low
Beam Assist-Static Light bulb
retaining wire into position by
aligning the wire with the groove
on the bulb.
7. Connect the Low Beam Assist- Static Light bulb socket connector.
8. Install the Low Beam Assist-Static Light bulb cover by turning it clock-
wise.
Parking (Position) light1. Remove the socket from theassembly by pulling it straight out.
2. Remove the bulb from the socket by pulling it out.
3. Insert a new bulb by inserting it into the socket.
4. Install the socket in the assembly by pushing it in.
Front fog light or Daytime runninglight (if equipped)
OIB075061
Low Beam Assist-Static Light
OIB077071OIB077072OIB077073
■
5 Door
• Type A (without DRL)■5 Door
• Type A (with DRL)■ Cross