2017 HYUNDAI I20 clock

##!'%$&%" '&$BBluetoothPress the
[SETUP]
button on the
audio system ➟ Select [Bluetooth].
• Connections: Control pairing, dele- tion, connection and disconnection
of Bluetooth
®
devices.
• Auto Connection Priority: Set the connection priority of B luetooth
®
devices when the vehicle is started.
• Download Contacts: Contacts can be downloaded from connectedBluetooth
®
devices.
Information
• When paired devices are deleted, the call history and contacts of the
device saved to the audio system are
deleted.
• For Bluetooth
®
connections with low
connection priority, some time may
be required for the connection to be
established.
• Contacts can be downloaded only from the currently connected
Bluetooth
®
device.
• If no Bluetooth
®
device is connected,
the Download Contacts button is
disabled.
SystemPress the
[SETUP]
button on the
audio system ➟ Select [System].
• Language: Change the user lan- guage.
• Default: Reset the audio system.
Information
The system resets to the default val-
ues, and all saved data and settings
are lost.Screen SaverSet the information displayed when
the audio system is switched off or
the screen is turned off.
Press the
[SETUP]
button on the
audio system ➟ Select [Screen
Saver].
• Analog: An analog clock is dis- played.
• Digital: A digital clock is displayed.
• None: No information is displayed.
Display OffTo prevent glare, the screen can be
turned off while the audio system in
operation.
Press the
[SETUP]
button on the
audio system ➟ Select [Display Off].
Information
Use ‘Screen Saver’ to set the informa-
tion to be displayed when the screen is
turned off.i
i
i

If your temperature gauge indicates
overheating, you experience a loss
of power, or hear loud pinging or
knocking, the engine may be over-
heating. If this happens, you should:
1.Pull off the road and stop as soonas it is safe to do so.
2.Place the shift lever in P (Park, for Continuously Variable Transaxle
vehicle) or neutral (for Manual
Transaxle vehicle) and set the
parking brake. If the air condition-
ing is ON, turn it OFF.
3.If engine coolant is running out under the vehicle or steam is com-
ing out from the hood, stop the
engine. Do not open the hood until
the coolant has stopped running or
the steaming has stopped. If there
is no visible loss of engine coolant
and no steam, leave the engine
running and check to be sure the
engine cooling fan is operating. If
the fan is not running, turn the
engine off. 4.Check for coolant leaking from the
radiator, hoses or under the vehi-
cle. (If the air conditioning had
been in use, it is normal for cold
water to be draining from it when
you stop.)
5.If engine coolant is leaking out, stop the engine immediately and
we recommend that you call an
authorized HYUNDAI dealer for
assistance.$$ !%%#$#%% %"!!!$#'#"'"' %'$%'&&&%
While the engine is run-
ning, keep hands,
clothing and tools away
from the moving parts
such as the cool ing fan
and drive belt to pre-
vent serious injury.WARNING
NEVER remove the
radiator cap or the
drain plug while the
engine and radiator are
hot. Hot coolant and
ste am may blow out under pres-
sure, causing serious injury.
Turn the engine off and wait until
the engine cools down. Use
extreme care when removing the
radiator cap. Wrap a thick towel
around it, and turn it c ounterclock-
wise slowly to the first stop. Step
back while the pressure is
released from the cooling sy stem.
When you are sure all the pres-
sure has been released, press
down on the cap, using a thick
towel, and continue turning coun-
terclockwise to remove it.WARNING

! $#'#"'"' %'$%'&&&%
JJack and tools ➀Jack
➁ Jack handle
➂ Wheel lug nut wrench
➃ Towing hook
The jack, jack handle, and wheel lug
nut wrench, towing hook are stored
in the luggage compartment under
the luggage box cover.
The jack is provided for emergency
tire changing only.
Removing and storing the spare
tireTurn the winged hold down bolt
counterclockwise to remove the
spare tire.
Store the spare tire in the same com-
partment by turning the winged hold
down bolt clockwise.
To prevent the spare tire and tools
from “rattling,” store them in their
proper location.
$"%""!!$ %
OIB067021
OIB067020
Changing a tire can be dangerous.
Follow the instructions in this sec-
tion when changing a tire to
redu ce the risk of serious injury or
death.
WARNING

!
$#'#"'"' %'$%'&&&%
If it is hard to loosen the tire hold-
down wing bolt by hand, you can
loosen it easily using the wheel lug
nut wrench.
1. Put the wrench (1) inside of the tire hold-down wing bolt.
2. Turn the tire hold-down wing bolt counterclockwise with the wrench.
CChanging tires A vehicle can slip or roll off of a
jack causing serious injury or
death to you or those nearby.
Take th e following safety precau-
tions:•
Do not get under a vehicle that
is supported by a jack.
•
NEVER attempt to change a tire
in the lane of traffic. ALWAYS
move the vehicle completely off
the road o n level, firm ground
away from traffic before trying to
change a tire. If you cannot find
a level, firm place off the road,
call a towing service for assis-
tance.
•
Be sure to use the jack provided
with the vehicle.
(Continued)
(Continued)•
ALWAYS place the jack on the
designated jacking positions on
the vehicle and NEVER on the
bumpers or any other part of the
vehicle for jacking support.
•
Do not start or run the engine
while the vehicle is on the jack.
•
Do not allow anyone to remain
in the vehicle while it is on the
jack.
•
Keep children away from the
road and the vehicle.
WARNING
OIB067022

!$#'#"'"' %'$%'&&&%
Follow these steps to change your
v ehicle’s tire:
1.Park on a level, firm surface.
2.Move the shift lever into P (Park, for Continuously Variable Transaxle
vehicle) or neutral (for Manual
Transaxle vehicle), apply the park-
ing brake, and place the ignition
switch in the LOCK/OFF position.
3.Press the hazard warning flasher button.
4.Remove the wheel lug nut wrench, jack, jack handle, and spare tire
from the vehicle.
5.Block both the front and rear of the tire diagonally opposite of the tire
you are changing. 6.Loosen the wheel lug nuts counter-
clockwise one turn each in the
order shown above, but do not
remove any lug nuts until the tire
has been raised off of the ground. 7.Place the jack at the designated
jacking position under the frame
closest to the tire you are chang-
ing. The jacking positions are
plates welded to the frame with two
tabs and a raised dot. Never jack
any other position or part of the
vehicle.
OIB067006
OIB067005

!

$#'#"'"' %'$%'&&&%
8.Insert the jack handle into the jackand turn it clockwise, raising the
vehicle until the tire clears the ground. Make sure the vehicle is
stable on the jack. 9.Loosen the lug nuts with the wheel
lug nut wrench and remove them
with your fingers. Remove the
wheel from the studs and lay it flat
on the ground out of the way.
Remove any dirt or debris from the
studs, mounting surfaces, and
wheel.
10. Install the spare tire onto the studs of the hub.
11. Tighten the lug nuts with your fin- gers onto the studs with the
smaller end of the lug nuts clos-
est to the wheel.
12. Lower the vehicle to the ground by turning the jack handle coun-
terclockwise. 13. Use the wheel lug nut wrench to
tighten the lug nuts in the order
shown. Double-check each lug
nut until they are tight. After
changing tires, we recommend
that an authorized HYUNDAI
dealer tighten the lug nuts to their
proper torque as soon as possi-
ble. T
T
he wheel lug nut should be
tightened to 11~13 kgf.m (79~94
lbf.ft).
OIB067008
OIB067007

!!$#'#"'"' %'$%'&&&%
•• Do not tow the vehicle with 4
wheels on the ground (such as
dinghy towing behind a motorhome
or other m otor vehicle) as this can
seriously damage the
Continuously Variable Transaxle.
• Do not tow the vehicle with the
front wheels on the ground as this
may cause damage to the vehicle.
• Do not tow with sling-type equip-
ment. Use a wheel lift or flatbed
equipment.When towing your vehicle in an
emergency without wheel dollies:
1. Place the ignition switch in the ACC position.
2. Place the shift lever in N (Neutral).
3. Release the parking brake.Failure to place the shift lever in N
(Neutral) when being towed with the
front wheels on the ground can
cause internal damage to the
transaxle.
Removable towing hook 1.Open the trunk, and remove the towing hook from the tool case. 2.Remove the hole cover pressing
the lower part of the cover on the
front bumper.
3.Install the towing hook by turning it clockwise into the hole until it is
fully secured.
4.Remove the towing hook and install the cover after use.
NOTICENOTICE
OIB067013OIB064017
■ 5 Door■Cross

1.#),204/3424-3
IInformation
If the memory fuse is pulled up from
the fuse panel, the warning chime,
audio, clock and interior lamps, etc.,
will not operate. Some items must
be reset after replacement. Refer to
"Battery" in this chapter.
Even though the memory fuse is pulled up, the battery can still be
discharged by operation of the
headlights or other electrical
devices.
Engine compartment panel fuse
replacement1. Turn the ignition switch and all
other switches off.
2. Remove the fuse box cover by pressing the tab and pulling up the
cover.
3. Check the removed fuse; replace it if it is blown. To remove or insert
the fuse, use the fuse puller in the
engine compartment fuse panel.
4. Push in a new fuse of the same rating, and make sure it fits tightly
in the clips. If it fits loosely, we rec-
ommend that you consult an
authorized HYUNDAI dealer.
After checking the fuse panel in the
engine compartment, securely install
the fuse panel cover. If not, electrical
failures may occur from water leak-
ing in.NOTICE
i
OIB074031