Page 23 of 606
22
Quick Reference Guide
Maintenance (P503)
Under the Hood (P511)
● Check engine oil, engine coolant, and windshield washer 
fluid. Add when necessary.
● Check brake fluid.
● Check the battery condition monthly.
aPull the hood release handle under the corner of the 
dashboard.
bLocate the hood latch lever, pull the lever up, and lift up 
the hood.
cWhen finished, close the hood  and make sure it is firmly 
locked in place.
Lights (P523)
● Inspect all lights regularly.
Wiper Blades (P529)
● Replace blades if they leave streaks 
across the windshield.
Tires (P531)
● Inspect tires and wheels regularly.
● Check tire pressures regularly.
● Install snow tires for winter 
driving. 
     
        
        Page 25 of 606
24
Quick Reference Guide
What to Do If
The power mode does not 
change from VEHICLE OFF 
(LOCK) to ACCESSORY. 
Why?
●The steering wheel may be locked.
●Move the steering wheel left and right 
after pressing the ENGINE START/STOP  
button.
The power mode does not 
change from ON to 
VEHICLE OFF  (LOCK). Why?The shift lever should be moved to (P.
Why does the brake pedal 
pulsate slightly when 
applying the brakes?This can occur when the ABS activates, and does not indicate a 
problem. Apply firm, steady pressure on the brake pedal. Never 
pump the brake pedal.
Canadian models 
     
        
        Page 26 of 606
25
Quick Reference Guide
The rear door cannot be 
opened from inside the 
vehicle. Why?Check if the childproof lock is in 
the lock position. If so, open the 
rear door with the outside door 
handle.
To cancel this function, push the 
lever to the unlock position.
Why do the doors lock 
after I unlocked the doors?If you do not open the doors within 30 seconds, the doors are 
relocked automatically for security.
Why does the beeper 
sound when I open the 
driver’s door?The beeper sounds when:
●The exterior lights are left on.
●The power mode is in ACCESSORY.
Why does the beeper 
sound when I start driving?The beeper sounds when:
●Driver and/or front passenger are not wearing their seat belts.
●The parking brake pedal is not fully released.
Why do I hear a screeching 
sound when I apply the 
brake pedal?The brake pads may need to be replaced. Have your vehicle 
inspected by a dealer. 
     
        
        Page 77 of 606
76
uuIndicators u
Instrument Panel
IndicatorNameOn/BlinkingExplanationMessage
Vehicle Stability 
Assist (VSA ®) 
System Indicator
●Comes on for a few seconds 
when you set the power mode to 
ON, then goes off.
●Blinks when VSA ®, or trailer 
stability assist is active.
●Comes on if there is a problem 
with the VSA ®, hill start assist, 
trailer stability assist or brake 
lighting system.
●Stays on constantly  - Have your vehicle 
checked by a dealer.
2 Vehicle Stability Assist (VSA ®), aka 
Electronic Stability Control (ESC), 
System  P. 462
2 Trailer Stability Assist P. 413
2 Hill start assist system  P. 423
●When Trailer Stability  Assist Problem is 
displayed on the multi-information display, 
the VSA ® does not activate. 
     
        
        Page 79 of 606

78
uuIndicators u
Instrument Panel
IndicatorNameOn/BlinkingExplanationMessage
Electric Power 
Steering (EPS) 
System Indicator
●Comes on when you set the 
power mode to ON, and goes off 
when the engine starts.
●Comes on if there is a problem 
with the EPS system.
●Stays on constantly or does not come on 
at all - Have your vehicle checked by a 
dealer.
2If the Electric Power Steering (EPS) 
System Indicator Comes On  P. 573
Low Tire Pressure/
TPMS Indicator
●Comes on for a few seconds 
when you set the power mode to 
ON, then goes off.
●Comes on if the tire pressure of 
any of the tires becomes 
significantly low.
●Blinks for about one minute, and 
then stays on if there is a problem 
with the TPMS with Tire Fill 
Assist, or when a compact spare 
tire is temporarily installed.
●Comes on while driving - Stop in a safe 
place, check tire pres sures, and inflate the 
tire(s) if necessary.
●Blinks and remains on - Have your vehicle 
checked by a dealer. If the vehicle is fitted 
with a compact spare, get your regular tire 
repaired or replaced and put back on your 
vehicle as soon as you can.
Turn Signal and 
Hazard Warning 
Indicators●Blinks when you operate the turn 
signal lever.
●Blink when you press the hazard 
warning button.
●Does not blink or blinks rapidly  - A turn 
signal light bulb has blown. Change the 
bulb immediately.
2 Replacing Light Bulbs  P. 526, 527
—
High Beam 
Indicator●Comes on when the high beam 
headlights are on.—— 
     
        
        Page 80 of 606

79
uuIndicators u
Continued
Instrument Panel
IndicatorNameOn/BlinkingExplanationMessage
Lights On 
Indicator●Comes on whenever the light 
switch is on, or in  AUTO when 
the exterior lights are on.●If you set the power mode to VEHICLE OFF 
(LOCK) while the lights  are on, a chime sounds 
when the driver’s  door is opened.
—
Auto high-beam 
Indicator*
●Comes on for a few seconds 
when you set the power mode to 
ON, then goes off.
●Comes on when all the operating 
conditions of the Auto high-
beam are met.
2Auto High-Beam (High Beam Support 
System)* P. 149—
Fog Light 
Indicator*
●Comes on when the fog lights 
are on.
——
Immobilizer 
System Indicator
●Comes on briefly when you set 
the power mode to ON, then 
goes off.
●Comes on if the immobilizer 
system cannot recognize the key 
information.
●Blinks  - You cannot start the engine. Set the 
power mode to VEHICL E OFF (LOCK), then 
select the ON mode again.
●Repeatedly blinks  - The system may be 
malfunctioning. Have your vehicle checked by 
a dealer.
●Do not attempt to alter this system or add 
other devices to it. Electrical problems can 
occur.
—
* Not available on all models 
     
        
        Page 89 of 606
88
uuIndicators u
Instrument Panel
IndicatorNameOn/BlinkingExplanationMessage
Bed Lights On 
Indicator
●Comes on when the bed lights 
are on.
●Comes on for 30 minutes when 
you set power mode to 
ACCESSORY or VEHICLE OFF 
(LOCK) without turning off the 
bed lights, then goes off.
2Bed Lights P. 184— 
     
        
        Page 95 of 606
94
uuIndicators uMulti-Information Display Warn ing and Information Messages
Instrument Panel
MessageConditionExplanation
●Appears when pressing the Intelligent Traction 
Management button.
2Intelligent Traction Management  P. 429
MessageConditionExplanation
●Appears if there is a problem with the headlights.●Appears while driving  - The low beam headlights 
may not be on. When conditions allow you to drive 
safety, have your vehicle chec ked by a dealer as soon as 
possible.
AWD models
2WD models
Models with LED low beam headlights