2017 FIAT 500L ECU

WARNING!(Continued)
properly attached and secured to your vehicle. If a
floor mat needs to be replaced, only use a FCA
approved floor mat for the specific make, model,
and year of your vehicle.
• ONLY use the driver ’s side floor mat on the
driver ’s side floor area. To check for interference,
with the vehicle properly parked with the engine
off, fully depress the accelerator, the brake, and
the clutch pedal (if present) to check for interfer-
ence. If your floor mat interferes with the opera-
tion of any pedal, or is not secure to the floor,
remove the floor mat from the vehicle and place
the floor mat in your trunk.
• ONLY use the passenger ’s side floor mat on the
passenger ’s side floor area.
• ALWAYS make sure objects cannot fall or slide
into the driver ’s side floor area when the vehicle
is moving. Objects can become trapped under
accelerator, brake, or clutch pedals and could
cause a loss of vehicle control.
• NEVER place any objects under the floor mat
(e.g., towels, keys, etc.). These objects could
(Continued)
WARNING! (Continued)
change the position of the floor mat and may
cause interference with the accelerator, brake, or
clutch pedals.
• If the vehicle carpet has been removed and re-
installed, always properly attach carpet to the
floor and check the floor mat fasteners are secure
to the vehicle carpet. Fully depress each pedal to
check for interference with the accelerator, brake,
or clutch pedals then re-install the floor mats.
• It is recommended to only use mild soap and
water to clean your floor mats. After cleaning,
always check your floor mat has been properly
installed and is secured to your vehicle using the
floor mat fasteners by lightly pulling mat.
Periodic Safety Checks You Should Make
Outside The Vehicle
Tires
Examine tires for excessive tread wear and uneven wear
patterns. Check for stones, nails, glass, or other objects
lodged in the tread or sidewall. Inspect the tread for
cuts and cracks. Inspect sidewalls for cuts, cracks and
2
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69

TILT/TELESCOPING STEERING COLUMN . . .99
 ELECTRONIC SPEED CONTROL ..........100
▫ To Activate ........................ .101
▫ To Set A Desired Speed ................101
▫ To Deactivate .......................101
▫ To Resume Speed ....................101
▫ To Vary The Speed Setting ..............101
▫ To Accelerate For Passing ..............103
 REAR PARK ASSIST — IF EQUIPPED .......103
▫ Rear Park Assist Sensors ...............104
▫ Rear Park Assist Audible Alerts ..........104
▫ Failure Indications ....................106
▫ Cleaning The Rear Park Assist System ......106
▫ Park Assist System Usage Precautions ......106
 PARKVIEW REAR BACK UP CAMERA — IF
EQUIPPED ..........................108
 GARAGE DOOR OPENER — IF EQUIPPED . .110 ▫
Before You Begin Programming HomeLink. . .110
▫ Programming A Rolling Code ............111
▫ Programming A Non-Rolling Code ........112
▫ Canadian/Gate Operator Programming .....114
▫ Using HomeLink .....................115
▫ Security ...........................115
▫ Troubleshooting Tips ..................116
▫ General Information ...................117
 POWER SUNROOF — IF EQUIPPED .......117
▫ To Open ...........................118
▫ To Close ...........................118
▫ Wind Buffeting ......................118
▫ Power Sun Blind .....................119
 POWER OUTLETS .....................119
 CIGAR LIGHTER

— IF EQUIPPED .........119
 CUPHOLDERS .......................120
 STORAGE .......................... .121
72 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

▫Glove Compartment ..................121
▫ Front Center Armrest Storage —
If Equipped ........................ .122
 REAR CARGO STORAGE FEATURES .......123
▫ Securing Your Load ...................126
▫ Storage Compartments .................127 
REAR WINDOW FEATURES .............127
▫ Rear Window Defroster ................127
 ROOF LUGGAGE RACK-IF EQUIPPED ......128
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 73

up. To reinstall the head restraint, put the head restraint
posts into the holes and push downward. Then adjust it
to the appropriate height.
The Reactive Head Restraints will automatically return
to their normal position following a rear impact. If the
Reactive Head Restraints do not return to their normal
position, see your authorized dealership immediately.NOTE:
Do not reposition the head restraint 180 degrees
to the incorrect position in an attempt to gain additional
clearance to the back of the head.
WARNING!
• A loose head restraint thrown forward in a colli-
sion or hard stop could cause serious injury or
death to occupants of the vehicle. Always securely
stow removed head restraints in a location out-
side the occupant compartment.
• ALL the head restraints MUST be reinstalled in
the vehicle to properly protect the occupants.
Follow the re-installation instructions above prior
to operating the vehicle or occupying a seat.
• Do not place items over the top of the Active
Head Restraint, such as coats, seat covers or
portable DVD players. These items may interfere
with the operation of the Reactive Head Restraint
in the event of a collision and could result in
serious injury or death.
Rear Head Restraints
The rear seats are equipped with adjustable head re-
straints, the outboard head restraints have two comfort
positions, while the central head restraint have to use in
1 — Release Button
2 — Adjustment Button
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87

the raised position. When there are no occupants in the
center seat, the head restraint can be lowered for
maximum visibility for the driver. When the center seat
is being occupied, the head restraint has to be in the
raised position.
NOTE:If the center rear head restraints requires re-
moval, see your authorized dealer.
To raise the outboard head restraints, pull upward on
the head restraint. To lower the head restraints, push
the adjustment button located at the base of the head
restraint, and push downward on the head restraint.
To remove the outboard head restraints, raise it as far as
it can go then push the adjustment button, and the
release button at the base of each post while pulling the
head restraint up. To reinstall the head restraint, put the
head restraint posts into the holes and push downward.
Then adjust it to the appropriate height.
WARNING!
A loose head restraint thrown forward in a collision
or hard stop could cause serious injury or death to
occupants of the vehicle. Always securely stow
(Continued)
WARNING! (Continued)
removed head restraints in a location outside the
occupant compartment.
For proper routing of a Child Seat Tether, refer to
“Occupant Restraints” in “Things to Know Before Start-
ing Your Vehicle.”
Adjustment Buttons
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

GARAGE DOOR OPENER — IF EQUIPPED
HomeLink replaces up to three remote controls (hand-
held transmitters) that operate devices such as garage
door openers, motorized gates, lighting or home secu-
rity systems. The HomeLink unit operates off your
vehicles battery.
The HomeLink buttons that are located in the sunvisor
designate the three different HomeLink channels. The
HomeLink
indicator is located above the center
button.
NOTE: HomeLink is disabled when the Vehicle Secu-
rity Alarm is active.
Before You Begin Programming HomeLink
Be sure that your vehicle is parked outside of the garage
before you begin programming.
For more efficient programming and accurate transmis-
sion of the radio-frequency signal, it is recommended
that a new battery be placed in the hand-held transmit-
ter of the device that is being programmed to the
HomeLink system.
To erase the channels, place the ignition in the ON/
RUN position and push and hold the two outside
HomeLink buttons (I and III) for up 20 seconds or until
the red indicator flashes.
NOTE:
• Erasing all channels should only be performed when
programming HomeLink for the first time. Do not
erase channels when programming additional but-
tons.
• If you have any problems, or require assistance,
please call toll-free 1-800-355-3515 or, on the Internet
at HomeLink.com for information or assistance.
HomeLink Buttons/Sunvisor
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

NOTE:•If the indicator light stays on constantly, program-
ming is complete and the garage door/device
should activate when the HomeLink button is
pushed.
• To program the two remaining HomeLink buttons,
repeat each step for each remaining button. DO
NOT erase the channels.
If you unplugged the garage door opener/device for
programming, plug it back in at this time.
Reprogramming A Single HomeLink Button
(Canadian/Gate Operator)
To reprogram a channel that has been previously
trained, follow these steps:
1. Cycle the ignition to the ON/RUN position.
NOTE: For vehicles equipped with Keyless Enter-N-
Go, place the ignition in the RUN position with the
engine ON. Make sure while programming HomeLink
with the engine ON that your vehicle is outside of your
garage, or that the garage door remains open at all
times. 2. Push and hold the desired HomeLink button until
the indicator light begins to flash after 20 seconds.
Do not release the button.
3. Without releasing the button, proceed with
“Canadian/Gate Operator Programming” step 2 and
follow all remaining steps.
Using HomeLink
To operate, switch the ignition to the ON/RUN position
and the press and release the programmed HomeLink
button. Activation will now occur for the programmed
device (i.e., garage door opener, gate operator, security
system, entry door lock, home/office lighting, etc.,).
The hand-held transmitter of the device may also be
used at any time. If the ignition is switched to the OFF
position, HomeLink will remain active for three min-
utes. During this time, if the vehicle is locked,
HomeLink is disabled.
Security
It is advised to erase all channels before you sell or turn
in your vehicle.
To do this, push and hold the two outside buttons for 20
seconds until the red indicator flashes.
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115

NOTE:All channels will be erased. Individual channels
cannot be erased.
The HomeLink Universal Transceiver is disabled when
the Vehicle Security Alarm is active.
Troubleshooting Tips
If you are having trouble programming HomeLink,
here are some of the most common solutions:
• Replace the battery in the Garage Door Opener
hand-held transmitter.
• Push the LEARN button on the Garage Door Opener
to complete the training for a Rolling Code.
• Did you unplug the device for programming and
remember to plug it back in?
If you have any problems, or require assistance, please
call toll-free 1-800-355-3515 or, on the Internet at
HomeLink.com for information or assistance.
WARNING!
• Vehicle exhaust contains carbon monoxide, a dan-
gerous gas. Do not run your vehicle in the garage
while programming the transceiver. Exhaust gas
can cause serious injury or death.
• Your motorized door or gate will open and close
while you are programming the universal trans-
ceiver. Do not program the transceiver if people,
pets or other objects are in the path of the door or
gate. Only use this transceiver with a garage door
opener that has a “stop and reverse” feature as
required by Federal safety standards. This in-
cludes most garage door opener models manufac-
tured after 1982. Do not use a garage door opener
without these safety features. Call toll-free 1-800-
355-3515 or, on the Internet at HomeLink.com for
safety information or assistance.
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE