2017 FIAT 500L ECO mode

motor. Firmly push and release the “LEARN” or
“TRAINING” button. On some garage door
openers/devices there may be a light that blinks
when the garage door opener/device is in the
LEARN/TRAIN mode.
NOTE: You have 30 seconds in which to initiate the next
step after the LEARN button has been pushed.
6. Return to the vehicle and push the programmed HomeLink button twice (holding the button for two
seconds each time). If the garage door opener/device
activates, programming is complete.
NOTE: If the garage door opener/device does not
activate, push the button a third time (for two seconds)
to complete the training.
To program the remaining two HomeLink buttons,
repeat each step for each remaining button. DO NOT
erase the channels.
Reprogramming A Single HomeLink Button
(Rolling Code)
To reprogram a channel that has been previously
trained, follow these steps:
1. Cycle the ignition to the ON/RUN position. NOTE:
For vehicles equipped with Keyless Enter-N-
Go, place the ignition in the RUN position with the
engine ON. Make sure while programming HomeLink
with the engine ON that your vehicle is outside of your
garage, or that the garage door remains open at all
times.
2. Push and hold the desired HomeLink button until the indicator light begins to flash after 20 seconds.
Do not release the button.
3. Without releasing the button, proceed with “Pro-
gramming A Rolling Code” step 2 and follow all
remaining steps.
Programming A Non-Rolling Code
For programming Garage Door Openers manufactured
before 1995:
1. Place the ignition in the ON/RUN position.
NOTE: For vehicles equipped with Keyless Enter-N-
Go, place the ignition in the RUN position with the
engine ON. Make sure while programming HomeLink
with the engine ON that your vehicle is outside of your
garage, or that the garage door remains open at all
times.
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

buffeting occurs with the sunroof open, adjust the
sunroof opening to minimize the buffeting or open any
window.
Power Sun Blind
Pull the power sun blind switch and the blind will
move towards the rear part of the vehicle, until it is fully
open.
With the blind fully open pull the power sun blind
switch and the blind will move towards the front part of
the vehicle, until it is fully closed.
NOTE:During the automatic opening and closing
stages, if the power sun blind switch is pulled again it
will stop the blind movement.
POWER OUTLETS
Passenger Compartment Power Socket
The power outlet is located on the central tunnel, in
front of the gear selector, between the two cup holders.
It only operates with the ignition key at MAR/ON.
On models with optional smoker ’s kit,the cigar
lighter takes the place of the power socket (see Cigar
lighter paragraph). NOTE:
Do not connect devices with power higher than
180 W to the socket. Do not damage the socket by using
unsuitable adaptors.CIGAR LIGHTER — IF EQUIPPED
This is located on the central tunnel, next to the parking
brake lever. To activate the cigar lighter, push and
release the knob. After a few seconds the knob auto-
matically returns to its initial position, and the cigar
lighter is ready for use.
Passenger Compartment Power Socket
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119

Distance Traveled
This value shows the distance covered since the last
reset.
Average Fuel Economy
This value shows the approximate average fuel con-
sumption since the last reset.
Instantaneous Fuel Economy
This indicates the fuel consumption. The value is con-
stantly updated. The message “----” will appear on the
display if the vehicle is parked with the engine running.
Average Speed
This value shows the vehicle’s average speed as a
function of the overall time elapsed since the last reset.
Travel Time
This value shows the time elapsed since the last reset.Personal Settings (Customer-Programmable
Features)
Dimmer
NOTE:The brightness of instrument panel will change
automatically only if the External Light has changed:
External Light On = Night Mode, External Light OFF =
Day Mode. In both case (Day or Night) is possible to
adjust the display brightness as described in step 1
below.
To adjust the brightness, proceed as follows:
1. Push and release the up
ordownbutton to
set the required brightness level.
2. Briefly push and release the MENUbutton to go
back to the menu screen or push and hold the MENU
(approximately one second) to go back to the main
screen without storing settings.
4
UNDERSTANDING YOUR INSTRUMENT PANEL 157

2. Push and release theupordown arrow button to
select Trip B data. Push and release the upordown
arrow button to turn ON or OFF.
3. Briefly push and release the MENUbutton to go
back to the menu screen, or push and hold the
MENU button (approximately one second) to go
back to the main screen without storing the settings.
Trip B Data Submenu Settings:
• On
• Off
• Return to MENU
Set Time (Clock)
This function may be used to set the clock through two
submenu items: “Time” and “Mode.”
Proceed as follows:
1. Briefly push and release the MENUbutton. Push and
release the up
ordownbuttons to highlight
Set Time — Push and release the MENUbutton.
2. Push and release the upordownbutton to
navigate the two sub-menu items.
3. Select the required option and then push and release the MENU button.
4. When accessing the “Time” sub-menu item, briefly push and release the MENUbutton and “hours” will
flash on the display.
5. Push and release the up
ordownbutton for
setting.
6. Briefly push and release the MENUbutton and
“minutes” will flash on the display.
7. Push and release the up
ordownbutton for
setting.
NOTE:
•The setting will increase or decrease by one unit
each time the up
ordownbutton is pushed.
Push and hold the button to increase/decrease
the setting rapidly. Save the setting by briefly
pushing the button when you approach the
required setting.
• Briefly push and release the MENUbutton to
return to the “Time” sub-function.
160 UNDERSTANDING YOUR INSTRUMENT PANEL

•When accessing the “Mode” submenu, briefly push
and release the MENUbutton. The previously set
display format will flash on the display.
• Push and release the up
ordownbutton to
select “24h” or “12h.”
When you have selected the required settings, briefly
push and release the MENUbutton to go back to the
Time, Mode sub-menu screen, or push and hold the
MENU button (approximately one second) to go back
to the main screen without storing the settings.
Set Date
This function may be used to set the date (day - month
- year).
To change, the date proceed as follows:
1. Briefly push and release the MENUbutton. Push and
release the up
ordownbutton to highlight
Date, push and release the MENUbutton and Year
will begin to flash.
2. Push and release the upordownbutton for
setting.
3. Briefly push and release the MENUbutton and
“month” will flash on the display. 4. Push and release the
up
ordownbutton for
setting.
5. Briefly push and release the MENUbutton and
“day” will flash on the display.
6. Push and release the up
ordownbutton for
setting.
NOTE: The setting will increase or decrease by one
unit each time the up
ordownbutton is
pushed. Push and hold the up
ordownbutton
to increase/decrease the setting rapidly. Save the
setting by briefly pushing the button when you
approach the required setting.
• Briefly push and release the MENUbutton to go back
to the menu screen, or push and hold the MENU
button (approximately one second) to go back to the
main screen without storing the settings.
First Page (Display Of Information On The Main
Screen)
This function allows you to choose the information you
would like to see on the main screen. You can view the
date or the trip distance.
4
UNDERSTANDING YOUR INSTRUMENT PANEL 161

Buttons On The Faceplate
Buttons on the faceplate are located below, and beside
the Uconnect system in the center of the instrument
panel. In addition, there is a Scroll/Enter control knob
located on the right side. Turn the control knob to scroll
through menus and change settings (i.e., 30, 60, 90),
push the center of the control knob one or more times to
select or change a setting (i.e., ON, OFF).
Your Uconnect system may also have Display Off and
back arrow buttons on the faceplate.
Push the Display Off button on the faceplate to turn off
the Uconnect screen. Push the Display Off button on the
faceplate a second time to turn the screen on.
Push the Back Arrow button on the faceplate to exit out
of a Menu or certain option on the Uconnect system.
Buttons On The Touchscreen
Buttons on the touchscreen are accessible on the
Uconnect touchscreen.
Customer Programmable Features — Uconnect
5.0 Settings
WARNING!
ALWAYS drive safely with your hands on the
wheel. You have full responsibility and assume all
risks related to the use of the Uconnect features and
applications in this vehicle. Only use Uconnect
when it is safe to do so. Failure to do so may result
in an accident involving serious injury or death.
Push the SETTINGS button on the faceplate to display
the settings menu screen. In this mode the Uconnect
system allows you to access programmable features
that may be equipped such as Display, Clock, Safety &
Driving Assistance, Lights, Doors & Locks, Auto-On
Comfort & Remote Start, Engine Off Options, Compass
Settings, Audio, Phone/Bluetooth, SiriusXM Setup and
System Information.
NOTE: Only one category may be selected at a time.
When making a selection, press the button on the
touchscreen to enter the desired mode. Once in the
desired mode, press and release the preferred setting
until the button is highlighted. Once the setting is
170 UNDERSTANDING YOUR INSTRUMENT PANEL

Safety & Driving Assistance
After pressing the “Safety & Driving Assistance” button
on the touchscreen the following settings will be avail-
able:
Setting NameSelectable Options
ParkView Backup Camera Delay On
Off
NOTE: When the vehicle is shifted out of REVERSE (with camera delay turned OFF), the rear camera mode is
exited and the navigation or audio screen appears again. When the vehicle is shifted out of REVERSE (with
camera delay turned ON), the rear view image with dynamic grid lines will be displayed for up to 10 seconds
after shifting out of “REVERSE” unless the forward vehicle speed exceeds 8 mph (12 km/h), the transmission is
shifted into “PARK” or the ignition is switched to the OFF position.
Blind Spot Alert — If Equipped Off
LightsLights & Chime
NOTE: When this feature is selected, the Blind Spot Alert feature can be set to Off, Lights or Lights and Chime.
The Blind Spot Alert feature can be activated in Lights mode. When this mode is selected, the Blind Spot Moni-
tor (BSM) system is activated and will only show a visual alert in the outside mirrors. When Lights & Chime
mode is activated, the Blind Spot Monitor (BSM) will show a visual alert in the outside mirrors as well as an
audible alert when the turn signal is on. When Off is selected, the Blind Spot Monitor (BSM) system is deacti-
vated.4
UNDERSTANDING YOUR INSTRUMENT PANEL 181

AUX/Media Player, etc.) and can also be used to
select/enter an item while scrolling through menu.
The left-hand control is a rocker-type switch with a
pushbutton in the center. The function of the left-hand
control is different depending on which mode you are
in.
The following describes the left-hand control operation
in each mode.
Radio Operation
Pushing the top of the switch will “Seek” up for the next
listenable station and pushing the bottom of the switch
will “Seek” down for the next listenable station.
The button located in the center of the left-hand control
will tune to the next preset station that you have
programmed in the radio preset button.
Player Operation
Pushing the top of the switch once will go to the next
track on the Player. Pushing the bottom of the switch
once will go to the beginning of the current track, or to
the beginning of the previous track if it is within one
second after the current track begins to play.If you push the switch up or down twice, it plays the
second track; three times, it will play the third, etc.
CD/DVD DISC MAINTENANCE
To keep a CD/DVD in good condition, take the follow-
ing precautions:
1. Handle the disc by its edge; avoid touching the
surface.
2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge.
3. Do not apply paper or tape to the disc; avoid scratching the disc.
4. Do not use solvents such as benzene, thinner, clean- ers, or anti-static sprays.
5. Store the disc in its case after playing.
6. Do not expose the disc to direct sunlight.
7. Do not store the disc where temperatures may be- come too high.
4
UNDERSTANDING YOUR INSTRUMENT PANEL 193