2017 DODGE VIPER battery replacement

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
CONTENTS
A WORD ABOUT YOUR KEYS ...............9
▫ Keyless Push Button Ignition ................9
▫ KeyFob...............................9
▫ Ignition Or Accessory On Message ...........11
▫ General Information .....................12
 SENTRY KEY ...........................12
▫ Replacement Key Fobs ...................13
▫ Customer Key Fob Programming ............13
▫ General Information .....................13
 VEHICLE SECURITY ALARM SYSTEM .........14
▫ Rearming Of The System ..................14
▫ To Arm The System ......................14
▫ To Disarm The System ....................14
 ILLUMINATED ENTRY ....................16 
REMOTE KEYLESS ENTRY .................16
▫ To Unlock The Doors .....................16
▫ To Lock The Doors .......................17
▫ To Unlatch The Liftgate ...................17
▫ Using The Panic Alarm ...................18
▫ Programming Additional Key Fobs ...........18
▫ Key Fob Battery Replacement ..............18
▫ General Information .....................19
 DOOR LOCKS ..........................20
▫ Power Door Locks ......................20
 WINDOWS .............................22
▫ Power Windows ........................22
▫ Auto-Down Feature .....................22
▫ Auto-Up Feature With Anti-Pinch Protection ....23
2

Using The Panic Alarm
To turn the Panic Alarm feature on or off, push and hold
the PANIC button on the key fob for at least one second
and release. When the Panic Alarm is on, the headlights
will turn on, the park lights will flash, the horn will pulse
on and off, and the interior lights will turn on.
The Panic Alarm will stay on for three minutes unless you
turn it off by either pushing the PANIC button a second
time or drive the vehicle at a speed of 15 MPH (24 km/h)
or greater.
NOTE:The interior lights will turn off if you cycle the
ignition switch to the ACC or ON/RUN position while the
Panic Alarm is activated. However, the exterior lights and
horn will remain on.
Programming Additional Key Fobs
Programming key fobs may be performed at an authorized
dealer.
Key Fob Battery Replacement
The recommended replacement battery is one CR2032
battery. NOTE:
•
Perchlorate Material — special handling may apply. See
www.dtsc.ca.gov/hazardouswaste/perchlorate
• Do not touch the battery terminals that are on the back
housing or the printed circuit board.
1. Remove the emergency key by sliding the mechanical latch on the back of the key fob sideways with your
thumb and then pull the key out with your other hand.Emergency Key Release
1 — Emergency Key Release Button
2 — Emergency Key
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

5. Remove the Speed Limit sticker from the instrumentpanel after the tire has been repaired.
6. Replace the Sealant Bottle (1) and Sealant Hose (6) assembly at your authorized dealer as soon as possible.
Refer to (F) “Sealant Bottle and Hose Replacement”.
NOTE: When having the tire serviced, advise the autho-
rized dealer or service center that the tire has been sealed
using the Tire Service Kit.
(F) Sealant Bottle And Hose Replacement:
1. Uncoil the Sealant Hose (6) (clear in color).
2. Locate the round Sealant Bottle release button in the recessed area under the sealant bottle.
3. Push the Sealant Bottle release button. The Sealant Bottle (1) will pop up. Remove the bottle and dispose of it
accordingly.
4. Clean any remaining sealant from the Tire Service Kit housing.
5. Position the new Sealant Bottle (1) in the housing so that the Sealant Hose (6) aligns with the hose slot in the front
of the housing. Push the bottle into the housing. An
audible click will be heard indicating the bottle is locked
into place. 6. Verify that the cap is installed on the fitting at the end of
the Sealant Hose (6) and return the hose to its storage
area (located on the bottom of the air pump).
7. Return the Tire Service Kit to its storage location in the vehicle.
JUMP-STARTING PROCEDURES
WARNING!
•Take care to avoid the radiator cooling fan whenever
the hood is raised. It can start anytime the ignition
switch is ON. You can be hurt by the fan.
• Do not attempt to push or tow your vehicle to get it
started. Unburned fuel could enter the catalytic con-
verter and once the engine has started, ignite and
damage the converter and vehicle. If the vehicle has
a discharged battery, booster cables may be used to
obtain a start from another vehicle. This type of start
can be dangerous if done improperly, so follow this
procedure carefully.
• Wear eye protection and remove any metal jewelry
such as watch bands or bracelets that might make an
inadvertent electrical contact. You could be seriously
injured.
256 WHAT TO DO IN EMERGENCIES

MAINTAINING YOUR VEHICLE
CONTENTS
ENGINE COMPARTMENT — 8.4L ...........263
 ONBOARD DIAGNOSTIC SYSTEM (OBD II) . . . .264
▫ Onboard Diagnostic System (OBD II)
Cybersecurity ........................ .264
 EMISSIONS INSPECTION AND MAINTENANCE
PROGRAMS .......................... .265
 REPLACEMENT PARTS ...................266
 DEALER SERVICE ...................... .266
 MAINTENANCE PROCEDURES .............267
▫ Engine Oil .......................... .267
▫ Engine Oil Filter ...................... .269
▫ Engine Air Cleaner Filter .................269
▫ Maintenance-Free Battery .................269
▫ Hibernation Mode ..................... .271
▫ Air Conditioner Maintenance ..............271▫
Body Lubrication ..................... .272
▫ Wiper Blades ........................ .273
▫ Adding Washer Fluid ...................273
▫ Exhaust System ....................... .274
▫ Cooling System ....................... .275
▫ Brake System ........................ .279
▫ Manual Transmission ....................281
▫ Hydraulic Clutch ..................... .281
▫ Rear Axle ........................... .282
▫ Appearance Care And Protection From
Corrosion ........................... .282
 FUSES ............................... .289
▫ Power Distribution Center ................289
 VEHICLE

STORAGE .....................294
7

WARNING!(Continued)
•Access, or allow others to access, information
stored in your vehicle systems, including personal
information.
For further information, refer to “Privacy Practices — If
Equipped With Uconnect 8.4 Radio” and “Uconnect Cy-
berSecurity” in “All About Uconnect Access” in your
Owner ’s Manual Radio Supplement and “Cybersecurity”
in “Understanding Your Instrument Panel”.
EMISSIONS INSPECTION AND MAINTENANCE
PROGRAMS
In some localities, it may be a legal requirement to pass an
inspection of your vehicle’s emissions control system.
Failure to pass could prevent vehicle registration. For states that require an Inspection and Mainte-
nance (I/M), this check verifies the “Malfunction
Indicator Light (MIL)” is functioning and is not on
when the engine is running, and that the OBD II system is
ready for testing.
Normally, the OBD II system will be ready. The OBD II
system may notbe ready if your vehicle was recently
serviced, or recently had a dead battery or a battery replacement. If the OBD II system should be determined
not ready
for the I/M test, your vehicle may fail the test.
Your vehicle has a simple ignition actuated test, which you
can use prior to going to the test station. To check if your
vehicle’s OBD II system is ready, you must do the follow-
ing:
1. Cycle the ignition to the ON mode, but do not crank or start the engine.
NOTE: If you crank or start the engine, you will have to
start this test over.
2. As soon as you cycle the ignition to the ON mode, you will see the “Malfunction Indicator Light (MIL)” symbol
come on as part of a normal bulb check.
3. Approximately 15 seconds later, one of two things will happen:
• The MIL will flash for about 10 seconds and then return
to being fully illuminated until you cycle the ignition
OFF or start the engine. This means that your vehicle’s
OBD II system is not readyand you should notproceed
to the I/M station.
7
MAINTAINING YOUR VEHICLE 265

•The MIL will not flash at all and will remain fully
illuminated until you place the ignition in the off posi-
tion or start the engine. This means that your vehicle’s
OBD II system is readyand you can proceed to the I/M
station.
If your OBD II system is not ready,you should see your
authorized dealer or repair facility. If your vehicle was
recently serviced or had a battery failure or replacement,
you may need to do nothing more than drive your vehicle
as you normally would in order for your OBD II system to
update. A recheck with the above test routine may then
indicate that the system is now ready.
Regardless of whether your vehicle’s OBD II system is
ready or not, if the MIL is illuminated during normal
vehicle operation you should have your vehicle serviced
before going to the I/M station. The I/M station can fail
your vehicle because the MIL is on with the engine
running.
REPLACEMENT PARTS
Use of genuine MOPAR parts for normal/scheduled main-
tenance and repairs is highly recommended to ensure the
designed performance. Damage or failures caused by the use of non-MOPAR parts for maintenance and repairs will
not be covered by the New Vehicle Limited Warranty.
DEALER SERVICE
Your authorized dealer has the qualified service personnel,
special tools, and equipment to perform all service opera-
tions in an expert manner. Service Manuals are available
which include detailed service information for your ve-
hicle. Refer to these Service Manuals before attempting any
procedure yourself.
NOTE:
Intentional tampering with emissions control sys-
tems may void your warranty and could result in civil
penalties being assessed against you.
WARNING!
You can be badly injured working on or around a
motor vehicle. Only do service work for which you
have the knowledge and the proper equipment. If you
have any doubt about your ability to perform a service
job, take your vehicle to a competent mechanic.
266 MAINTAINING YOUR VEHICLE

Engine Oil Filter
The engine oil filter should be replaced with a new filter at
every engine oil change.
Engine Oil Filter Selection
This manufacturer’s engines have a full-flow type oil filter. Use
a filter of this type for replacement. The quality of replacement
filters varies considerably. Only high quality filters should be
used to assure most efficient service. MOPAR engine oil filters
are high quality oil filters and are recommended.
Engine Air Cleaner Filter
Refer to the “Maintenance Schedule” for the proper main-
tenance intervals.
WARNING!
The air induction system (air cleaner, hoses, etc.) can
provide a measure of protection in the case of engine
backfire. Do not remove the air induction system (air
cleaner, hoses, etc.) unless such removal is necessary
for repair or maintenance. Make sure that no one is
near the engine compartment before starting the ve-
hicle with the air induction system (air cleaner, hoses,
(Continued)
WARNING!(Continued)
etc.) removed. Failure to do so can result in serious
personal injury.
Engine Air Cleaner Filter Selection
The quality of replacement engine air cleaner filters varies
considerably. Only high quality filters should be used to
assure most efficient service. MOPAR engine air cleaner
filters are a high quality filter and are recommended.
CAUTION!
Some aftermarket air cleaners and filters can cause
mass air flow sensor issues which can lead to a
driveability problem or a limp home condition.
Maintenance-Free Battery
The top of the maintenance-free battery is vented, and
must be replaced with a vented battery.
The battery is located underneath an access panel inside the
rear compartment on the left side of the vehicle. A remote
battery terminal is located in the engine compartment for
jump-starting. Refer to “Jump-Starting Procedures” in “What
To Do In Emergencies” for further information.
7
MAINTAINING YOUR VEHICLE 269

Battery.............................. .120, 269
Charging System Light ....................120
Emergency Starting ...................... .256
Jump Starting .......................... .256
Key Fob Battery Replacement .................18
Keyless Key Fob Replacement ................18
Location .............................. .269
Remote Battery Replacement .................18
Saving Feature (Protection) ..................271
Storing Vehicle ......................... .271
Belts, Seat .................................67
Body Mechanism Lubrication ..................272
B-Pillar Location .......................... .215
Brake Control System, Electronic ................205
Brake, Parking ............................ .202
Brake System ......................... .203, 279
Anti-Lock (ABS) ..................... .203, 205
Fluid Check ........................ .280, 300
Master Cylinder ........................ .280
Warning Light ...........................117
Break-In Recommendations, New Vehicle ..........204
Brightness, Interior Lights .....................86
Bulb Replacement ......................... .297
Bulbs, Light ........................... .69, 296Camera, Rear
..............................95
Capacities, Antifreeze (Engine Coolant) ...........298
Capacities, Fluid .......................... .298
Caps, Filler Oil (Engine) ........................... .268
Power Steering ......................... .202
Radiator (Coolant Pressure) .................278
Carbon Monoxide Warning .................66, 238
Car Washes .............................. .282
Chains, Tire ............................. .228
Chart, Tire Sizing ...........................211
Check Engine Light (Malfunction Indicator Light). . . .265
Checking Your Vehicle For Safety ................66
Checks, Safety .............................66
Child Restraint .............................
55
Child Restraints Booster Seats ............................58
Child Restraints ..........................55
Child Seat Installation ......................61
Infants And Child Restraints .................57
Older Children And Child Restraints ...........57
Using The Top Tether Anchorage ..............62
Clean Air Gasoline ........................ .235
Cleaning Wheels ............................... .283
10
INDEX 315