2017 DODGE VIPER radio

2. Installing aftermarket window tinting that contains ma-terials that may block radio wave signals.
3. Accumulation of snow or ice around the wheels or wheel housings.
4. Using tire chains on the vehicle.
5. Using wheels/tires not equipped with TPM sensors.
TPMS Deactivation — If Equipped
The TPMS can be deactivated if replacing all four wheel
and tire assemblies (road tires) with wheel and tire assem-
blies that do not have TPMS Sensors, such as when
installing Winter wheel and tire assemblies on your ve-
hicle. To deactivate the TPMS, first, replace all four wheel
and tire assemblies (road tires) with tires not equipped
with Tire Pressure Monitoring (TPM) Sensors. Then, drive
the vehicle for 20 minutes above 15 mph (24 km/h). The
TPMS will chime, the “TPM Telltale Light” will flash on
and off for 75 seconds and then remain on and the
instrument cluster will display the “SERVICE TPM SYS-
TEM” message and then display dashes (--) in place of the
pressure values. Beginning with the next ignition switch
cycle, the TPMS will no longer chime or flash the TPM
telltale and display the “SERVICE TPM SYSTEM” message
in the instrument cluster display but dashes (--) will remain
in place of the pressure values. To reactivate the TPMS, replace all four wheel and tire
assemblies (road tires) with tires equipped with TPM
sensors. Then, drive the vehicle for up to 20 minutes above
15 mph (24 km/h). The TPMS will chime, the “TPM Telltale
Light” will flash on and off for 75 seconds and then turn
off, and the instrument cluster will display the “SERVICE
TPM SYSTEM” message. The instrument cluster will also
display pressure values in place of the dashes. On the next
ignition switch cycle the “SERVICE TPM SYSTEM” mes-
sage will no longer be displayed as long as no system fault
exists.
General Information
The following regulatory statement applies to all radio
frequency (RF) devices equipped in this vehicle:
This device complies with Part 15 of the FCC Rules and
with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received,
including interference that may cause undesired operation.
NOTE:
Changes or modifications not expressly approved
by the party responsible for compliance could void the
user ’s authority to operate the equipment.
234 STARTING AND OPERATING

NOTE:The battery is located underneath an access panel
inside the rear compartment on the left side of the vehicle.
A remote battery terminal is located in the engine compart-
ment for jump-starting. Connecting The Jumper Cables
1. Wear eye protection and remove any metal jewelry such
as watchbands or bracelets that might make an inadver-
tent electrical contact.
2. When boost is provided by a battery in another vehicle, park that vehicle within booster cable reach, but without
allowing the vehicles to touch one another.
3. Set the parking brake, place the transmission in NEU- TRAL, and turn the ignition OFF on both vehicles.
4. Turn off the heater, radio, and all unnecessary electrical loads.
5. Remove the plastic fuse cover to gain access to the remote jump-start positive (+)post in the engine com-
partment. Refer to the following illustration for remote
jump-starting connections.
Battery Location
1 — Positive Battery Post
2 — Negative Battery Post
6
WHAT TO DO IN EMERGENCIES 257

WARNING!(Continued)
•Access, or allow others to access, information
stored in your vehicle systems, including personal
information.
For further information, refer to “Privacy Practices — If
Equipped With Uconnect 8.4 Radio” and “Uconnect Cy-
berSecurity” in “All About Uconnect Access” in your
Owner ’s Manual Radio Supplement and “Cybersecurity”
in “Understanding Your Instrument Panel”.
EMISSIONS INSPECTION AND MAINTENANCE
PROGRAMS
In some localities, it may be a legal requirement to pass an
inspection of your vehicle’s emissions control system.
Failure to pass could prevent vehicle registration. For states that require an Inspection and Mainte-
nance (I/M), this check verifies the “Malfunction
Indicator Light (MIL)” is functioning and is not on
when the engine is running, and that the OBD II system is
ready for testing.
Normally, the OBD II system will be ready. The OBD II
system may notbe ready if your vehicle was recently
serviced, or recently had a dead battery or a battery replacement. If the OBD II system should be determined
not ready
for the I/M test, your vehicle may fail the test.
Your vehicle has a simple ignition actuated test, which you
can use prior to going to the test station. To check if your
vehicle’s OBD II system is ready, you must do the follow-
ing:
1. Cycle the ignition to the ON mode, but do not crank or start the engine.
NOTE: If you crank or start the engine, you will have to
start this test over.
2. As soon as you cycle the ignition to the ON mode, you will see the “Malfunction Indicator Light (MIL)” symbol
come on as part of a normal bulb check.
3. Approximately 15 seconds later, one of two things will happen:
• The MIL will flash for about 10 seconds and then return
to being fully illuminated until you cycle the ignition
OFF or start the engine. This means that your vehicle’s
OBD II system is not readyand you should notproceed
to the I/M station.
7
MAINTAINING YOUR VEHICLE 265

CAUTION!(Continued)
•If a “fast charger” is used while the battery is in the
vehicle, disconnect both vehicle battery cables before
connecting the charger to the battery. Do not use a
“fast charger” to provide starting voltage.
Hibernation Mode
The Hibernation mode feature conserves battery power
when storing the vehicle. It allows for up to three months
of storage time without losing radio and engine controller
adaptive memory. Using this feature is an alternative to
disconnecting the battery.
NOTE: This vehicle is designed to sit in storage with a
fully charged battery for up to 30 days. If you plan to store
the vehicle longer than 30 days, we recommend doing one
of the following:
• Disconnect the battery.
• Use the battery charger.
• Put the vehicle into Hibernation mode (3-month charge).
To Activate Hibernation Mode
1. Cycle the ignition switch to (ACC).
2. Select Hibernation mode within the instrument cluster
display.
3. Push the right arrow button on the steering wheel controls for one second. Vehicle will countdown from
ten seconds and enter Hibernation Mode.
NOTE: You may push the right arrow button on the
steering wheel controls during the countdown to abort
Hibernation Mode.
To Deactivate Hibernation Mode
1. Push the key fob UNLOCK button to unlock the vehicle.
2. Push the ignition switch to the ON/RUN position.
Air Conditioner Maintenance
For best possible performance, your air conditioner should
be checked and serviced by an authorized dealer at the
start of each warm season. This service should include
cleaning of the condenser fins and a performance test.
Drive belt tension should also be checked at this time.
7
MAINTAINING YOUR VEHICLE 271

WARNING!
Do not use volatile solvents for cleaning purposes.
Many are potentially flammable, and if used in closed
areas they may cause respiratory harm.
CAUTION!
Direct contact of air fresheners, insect repellents, sun-
tan lotions, or hand sanitizers to the plastic, painted, or
decorated surfaces of the interior may cause permanent
damage. Wipe away immediately.
CAUTION!
Damage caused by these type of products may not be
covered by your New Vehicle Limited Warranty.
CAUTION!
Do not use Alcohol and Alcohol-based and/or Keton
based cleaning products to clean leather seats, as
damage to the seat may result.
Leather Or Vinyl Seat/Trim Care And Cleaning
Leather is best preserved by regular cleaning with a damp
soft cloth. Small particles of dirt can act as an abrasive and
damage the leather surface and should be removed imme-
diately with a damp cloth. Stubborn soils can be removed
easily with a soft cloth and MOPAR Total Clean or equiva-
lent. Care should be taken to avoid soaking the leather with
any liquid. Please do not use polishes, oils, cleaning fluids,
solvents, detergents, or ammonia-based cleaners to clean
the leather. Application of a leather conditioner is not
required to maintain the original condition.
Glass Surfaces
All glass surfaces should be cleaned on a regular basis with
MOPAR Glass Cleaner, or any commercial household-type
glass cleaner. Never use an abrasive type cleaner. Use
caution when cleaning the inside rear window equipped
with electric defrosters or windows equipped with radio
antennas. Do not use scrapers or other sharp instrument
that may scratch the elements.
When cleaning the rear view mirror, spray cleaner on the
towel or cloth that you are using. Do not spray cleaner
directly on the mirror.
7
MAINTAINING YOUR VEHICLE 285

Cavity RelayCartridge FuseMini-Fuse Description
50 HC Micro — —Rad Fan
51 HC Micro — —Rad Fan Relay SER/PAR
52 HC Micro — —Starter Relay
53 HC Micro — —Rear Window Defroster Relay
54 HC Relay — —Rad Fan Relay High
55 HC Micro — —Wiper ON/OFF
56 HC Micro — —Wiper LO/HI
57 G8VA — —Horn Relay
58 G8VA — —A/C Clutch Relay
59 HC Micro — —HVAC Blower
60 HC Micro — —Fuel Pump
61 G8VA — —Run Relay #1
62 G8VA — —Run Relay #2
63 HC Micro — —ASD #1
64 HC Micro — —ASD #2
65 G8VA — —Run Accy #1, Pop Up, Driver Door Window Switch
66 — ——Not Used
NOTE: A 15 Amp fuse for the radio system is located
in-line at the battery positive terminal.
7
MAINTAINING YOUR VEHICLE 293

Radial Ply Tires........................... .222
Radiator Cap (Coolant Pressure Cap) .............278
Radio Antenna ........................... .160
Radio Frequency General Information ..................12, 13, 19
Radio Operation .......................... .160
Radio (Sound Systems) ..................... .158
Rear Camera ...............................95
Rear Liftgate ...............................24
Rear Window Defroster ......................110
Rear Window Features .......................110
Reclining Front Seats .........................78
Recreational Towing ........................ .242
Reformulated Gasoline ...................... .235
Refrigerant .............................. .272
Reminder, Lights On .........................85
Reminder, Seat Belt ..........................27
Remote Keyless Entry ........................16
Key Fob Battery Replacement .................18
Programming Additional Key Fobs .............13
Remote Battery Replacement .................18
Remote Sound System (Radio) Controls ...........159
Replacement Keys ...........................13
Replacement Parts ......................... .266
Replacement Tires ......................... .227Reporting Safety Defects
......................311
Restraint, Head .............................81
Restraints, Child ............................55
Rocking Vehicle When Stuck ...................259
Rotation, Tires ............................ .229
Safety Checks Inside Vehicle ...................67
Safety Checks Outside Vehicle ..................69
Safety Defects, Reporting .....................311
Safety, Exhaust Gas ..........................66
Safety Information, Tire ..................... .210
Safety Tips ................................66
Schedule, Maintenance ...................301, 302
Seat Belt Automatic Locking Retractor (ALR) ............34
Energy Management Feature .................33
Lap/Shoulder Belt Operation .................30
Lap/Shoulder Belts ........................28
Lap/Shoulder Belt Untwisting ................32
Pregnant Women .........................33
Seat

Belt Extender .........................32
Seat Belt Pretensioner ......................33
Seat Belt Reminder ........................27
Seat Belt Maintenance ...................... .286
Seat Belt Reminder ..........................27
322 INDEX

INSTALLATION OF RADIO TRANSMITTING
EQUIPMENT
Special design considerations are incorporated into this
vehicle’s electronic system to provide immunity to radio
frequency signals. Mobile two-way radios and telephone
equipment must be installed properly by trained person-
nel. The following must be observed during installation.
The positive power connection should be made directly
to the battery and fused as close to the battery as possible.
The negative power connection should be made to body
sheet metal adjacent to the negative battery connection.
This connection should not be fused.
Antennas for two-way radios should be mounted on the
roof or the rear area of the vehicle. Care should be used
in mounting antennas with magnet bases. Magnets may
affect the accuracy or operation of the compass on
vehicles so equipped.The antenna cable should be as short as practical and
routed away from the vehicle wiring when possible. Use
only fully shielded coaxial cable.
Carefully match the antenna and cable to the radio to
ensure a low Standing Wave Ratio (SWR).
Mobile radio equipment with output power greater than
normal may require special precautions.
All installations should be checked for possible interfer-
ence between the communications equipment and the
vehicle’s electronic systems.