2017 DODGE DURANGO service indicator

Service Stop/Start System Indicator Light — If Equipped
Yellow TelltaleLight What It Means
Service Stop/Start System Indicator Light — If Equipped
This telltale will turn on to indicate the Stop/Start system is not functioning properly and service
is required.
LaneSense Indicator Light — If Equipped
Yellow Telltale
Light What It Means
LaneSense Indicator Light — If Equipped
The LaneSense is solid yellow when the system senses a lane drift situation.
The LaneSense is flashing yellow when the system senses the lane has been approached and is in
a lane departure situation.
Refer to “LaneSense - If Equipped
in “Understanding The Features Of Your Vehicle” for further
information.
LaneSense Failure Indicator Light — If Equipped
Yellow Telltale Light What It Means
LaneSense Failure Indicator Light
This light will turn on when the LaneSense system is not operating and needs service. Please see
your authorized dealer.
4
UNDERSTANDING YOUR INSTRUMENT PANEL 253

▫Tire Pressures For High Speed Operation .....429
▫ Radial Ply Tires ....................... .429
▫ Tire Types ........................... .430
▫ Run Flat Tires — If Equipped ..............431
▫ Spare Tires — If Equipped ................431
▫ Tire Spinning ........................ .434
▫ Tread Wear Indicators ...................435
▫ Life Of Tire .......................... .435
▫ Replacement Tires ..................... .436
 TIRE CHAINS (TRACTION DEVICES) .........437
 TIRE ROTATION RECOMMENDATIONS ......438
 TIRE PRESSURE MONITOR SYSTEM (TPMS) . . . .439
▫ Tire Pressure Monitoring Low Pressure
Warnings ............................ .441
▫ Service TPM System Warning ..............442
▫ TPMS Deactivation — If Equipped ...........443
▫ General Information ....................444 
FUEL REQUIREMENTS ....................444
▫ 3.6L Engine .......................... .444
▫ 5.7L Engine .......................... .445
▫ Reformulated Gasoline ..................445
▫ Materials Added To Fuel .................446
▫ Gasoline/Oxygenate Blends ...............446
▫ E-85 Usage In Non-Flex Fuel Vehicles .........447
▫ CNG And LP Fuel System Modifications ......447
▫ MMT In Gasoline ...................... .447
▫ Fuel System Cautions ....................448
▫ Carbon

Monoxide Warnings ...............448
 ADDING FUEL ........................ .449
▫ Emergency Fuel Filler Door Release ..........450
 VEHICLE LOADING .....................451
▫ Certification Label ..................... .451
 TRAILER TOWING ..................... .453
▫ Common Towing Definitions ...............453
5
STARTING AND OPERATING 377

Tread Wear Indicators
Tread wear indicators are in the original equipment tires to
help you in determining when your tires should be replaced.
These indicators are molded into the bottom of the tread
grooves. They will appear as bands when the tread depth
becomes a 1/16 of an inch (1.6 mm). When the tread is
worn to the tread wear indicators, the tire should be
replaced. Refer to “Replacement Tires” in this section for
further information.
Life Of Tire
The service life of a tire is dependent upon varying factors
including, but not limited to:
•Driving style.
• Tire pressure - Improper cold tire inflation pressures can
cause uneven wear patterns to develop across the tire
tread. These abnormal wear patterns will reduce tread
life, resulting in the need for earlier tire replacement.
• Distance driven.
• Performance tires, tires with a speed rating of V or
higher, and Summer tires typically have a reduced tread
life. Rotation of these tires per the vehicle maintenance
schedule is highly recommended.
Tire Tread
1—WornTire
2—NewTire
5
STARTING AND OPERATING 435

ONBOARD DIAGNOSTIC SYSTEM (OBD II)
Your vehicle is equipped with a sophisticated onboard
diagnostic system called OBD II. This system monitors the
performance of the emissions, engine, and automatic trans-
mission control systems. When these systems are operating
properly, your vehicle will provide excellent performance
and fuel economy, as well as engine emissions well within
current government regulations.
If any of these systems require service, the OBD II system
will turn on the “Malfunction Indicator Light (MIL).” It
will also store diagnostic codes and other information to
assist your service technician in making repairs. Although
your vehicle will usually be drivable and not need towing,
see your authorized dealer for service as soon as possible.
CAUTION!
•Prolonged driving with the MIL on could cause
further damage to the emission control system. It
could also affect fuel economy and driveability. The
vehicle must be serviced before any emissions tests
can be performed.
• If the MIL is flashing, while the engine is running,
severe catalytic converter damage and power loss
will soon occur. Immediate service is required.
Onboard Diagnostic System (OBD II) Cybersecurity
Your vehicle is required to have an Onboard Diagnostic
system (OBD II) and a connection port to allow access to
information related to the performance of your emissions
controls. Authorized service technicians may need to ac-
cess this information to assist with the diagnosis and
service of your vehicle and emissions system.
7
MAINTAINING YOUR VEHICLE 505

WARNING!
•ONLY an authorized service technician should con-
nect equipment to the OBD II connection port in
order to diagnose or service your vehicle.
• If unauthorized equipment is connected to the OBD
II connection port, such as a driver-behavior tracking
device, it may:
• Be possible that vehicle systems, including safety
related systems, could be impaired or a loss of
vehicle control could occur that may result in an
accident involving serious injury or death.
• Access, or allow others to access, information
stored in your vehicle systems, including personal
information.
For further information, refer to “Privacy Practices — If
Equipped With Uconnect 8.4 Radio” and “Uconnect Cy-
berSecurity” in “All About Uconnect Access” in your
Owner ’s Manual Radio Supplement and “Cybersecurity”
in “Understanding Your Instrument Panel”.
EMISSIONS INSPECTION AND MAINTENANCE
PROGRAMS
In some localities, it may be a legal requirement to pass an
inspection of your vehicle’s emissions control system.
Failure to pass could prevent vehicle registration. For states that require an Inspection and Mainte-
nance (I/M), this check verifies the “Malfunction
Indicator Light (MIL)” is functioning and is not on
when the engine is running, and that the OBD II system is
ready for testing.
Normally, the OBD II system will be ready. The OBD II
system may notbe ready if your vehicle was recently
serviced, recently had a dead battery or a battery replace-
ment. If the OBD II system should be determined not ready
for the I/M test, your vehicle may fail the test.
Your vehicle has a simple ignition actuated test, which you
can use prior to going to the test station. To check if your
vehicle’s OBD II system is ready, you must do the follow-
ing:
1. Cycle the ignition switch to the ON position, but do not crank or start the engine.
NOTE: If you crank or start the engine, you will have to
start this test over.
506 MAINTAINING YOUR VEHICLE

2. As soon as you cycle the ignition switch to the ONposition, you will see the “Malfunction Indicator Light
(MIL)” symbol come on as part of a normal bulb check.
3. Approximately 15 seconds later, one of two things will happen:
• The MIL will flash for about 10 seconds and then return
to being fully illuminated until you turn OFF the igni-
tion or start the engine. This means that your vehicle’s
OBD II system is not readyand you should notproceed
to the I/M station.
• The MIL will not flash at all and will remain fully
illuminated until you place the ignition in the off posi-
tion or start the engine. This means that your vehicle’s
OBD II system is readyand you can proceed to the I/M
station.
If your OBD II system is not ready,you should see your
authorized dealer or repair facility. If your vehicle was
recently serviced or had a battery failure or replacement,
you may need to do nothing more than drive your vehicle
as you normally would in order for your OBD II system to
update. A recheck with the above test routine may then
indicate that the system is now ready. Regardless of whether your vehicle’s OBD II system is
ready or not, if the MIL is illuminated during normal
vehicle operation you should have your vehicle serviced
before going to the I/M station. The I/M station can fail
your vehicle because the MIL is on with the engine
running.
REPLACEMENT PARTS
Use of genuine MOPAR parts for normal/scheduled main-
tenance and repairs is highly recommended to ensure the
designed performance. Damage or failures caused by the
use of non-MOPAR parts for maintenance and repairs will
not be covered by the New Vehicle Limited Warranty.
DEALER SERVICE
Your authorized dealer has the qualified service personnel,
special tools, and equipment to perform all service opera-
tions in an expert manner. Service Manuals are available
which include detailed service information for your ve-
hicle. Refer to these Service Manuals before attempting any
procedure yourself.
NOTE:
Intentional tampering with emissions control sys-
tems may void your warranty and could result in civil
penalties being assessed against you.
7
MAINTAINING YOUR VEHICLE 507

MAINTENANCE SCHEDULE
Your vehicle is equipped with an automatic oil change
indicator system. The oil change indicator system will
remind you that it is time to take your vehicle in for
scheduled maintenance.
Based on engine operation conditions, the oil change
indicator message will illuminate. This means that service
is required for your vehicle. Operating conditions such as
frequent short-trips, trailer tow, extremely hot or cold
ambient temperatures, and E85 fuel usage will influence
when the “Oil Change Required” message is displayed.
Severe Operating Conditions can cause the change oil
message to illuminate as early as 3,500 miles (5,600 km)
since last reset. Have your vehicle serviced as soon as
possible, within the next 500 miles (805 km).
Your authorized dealer will reset the oil change indicator
message after completing the scheduled oil change.
NOTE:Under no circumstances should oil change inter-
vals exceed 10,000 miles (16,000 km), twelve months or 350
hours of engine run time, whichever comes first. The 350
hours of engine run or idle time is generally only a concern
for fleet customers. Severe Duty All Models
Change Engine Oil at 4,000 miles (6,500 km) if the vehicle
is operated in a dusty and off road environment or is
operated predominately at idle or only very low engine
RPM’s. This type of vehicle use is considered Severe Duty.
Once A Month Or Before A Long Trip:
•
Check engine oil level
• Check windshield washer fluid level
• Check the tire inflation pressures and look for unusual
wear or damage
• Check the fluid levels of the coolant reservoir, brake
master cylinder and fill as needed.
• Check function of all interior and exterior lights
552 MAINTENANCE SCHEDULES

Changing A Flat Tire....................... .476
Chart, Tire Sizing .......................... .419
Check Engine Light (Malfunction Indicator Light). . . .506
Checking Your Vehicle For Safety ................84
Checks, Safety .............................84
Child Restraint .............................63
Child Restraints Booster Seats ............................68
Child Restraints ..........................63
Child Seat Installation ......................80
How To Stow An Unused ALR Seat Belt .........77
Infants And Child Restraints .................66
Locating The LATCH Anchorages ..............73
Lower Anchors And Tethers For Children ........70
Older Children And Child Restraints ...........67
Seating Positions ..........................69
Child Safety Locks ..........................28
Clean Air Gasoline ........................ .445
Cleaning Wheels ............................... .530
Climate Control ........................... .336
Manual ............................... .336
Cold Weather Operation ..................... .381
Compact Disc (CD) Maintenance ................333
Compact Spare Tire ........................ .432Console, Overhead
........................ .194
Contract, Service .......................... .560
Coolant Pressure Cap (Radiator Cap) .............523
Cooling System ........................... .520
Adding Coolant (Antifreeze) .................522
Coolant Capacity ........................ .545
Coolant Level .......................... .523
Disposal Of Used Coolant ..................523
Drain, Flush, And Refill ....................521
Inspection ......................... .520, 523
Points To Remember ..................... .524
Pressure Cap ........................... .523
Radiator Cap .......................... .523
Selection Of Coolant (Antifreeze) .......521, 545, 547
Corrosion Protection ....................... .528
Cr

uise Control (Speed Control) .................153
Cruise Light .......................... .255, 257
Cupholders ...............................211
Customer Assistance ....................... .558
Daytime Running Lights .....................137
Dealer Service ............................ .507
Defroster, Rear Window ..................... .223
Defroster, Windshield ........................86
568 INDEX