2017 DODGE DURANGO lights

▫Head Restraints ........................119
▫ 60/40 Split Rear Seat ....................123
▫ Rear Captain’s Chairs — If Equipped .........126
▫ Folding Third Row ..................... .129
 DRIVER MEMORY SEAT — IF EQUIPPED .....130
▫ Programming The Memory Feature ..........131
▫ Linking And Unlinking The Remote Keyless Entry
Key Fob To Memory .....................131
▫ Memory Position Recall ..................132
▫ Easy Entry/Exit Seat ....................132
 TO OPEN AND CLOSE THE HOOD ..........133
 LIGHTS ............................. .135
▫ Headlight Switch ..................... .135
▫ Automatic Headlights ...................136
▫ Headlights On Automatically With Wipers . . . .136
▫ Automatic High Beam — If Equipped ........136
▫ Daytime Running Lights — If Equipped ......137▫
Headlight Delay ....................... .137
▫ Parking Lights And Panel Lights ............137
▫ Fog Lights — If Equipped .................138
▫ Interior Lights ........................ .138
▫ Lights-On Reminder .....................139
▫ Battery Saver ......................... .139
▫ Front Map/Reading Lights — If Equipped . . . .140
▫ Courtesy Lights ....................... .141
▫ Ambient Light — If Equipped .............141
▫ Multifunction Lever ................... .142
▫ T

urn Signals ......................... .142
▫ Lane Change Assist .....................142
▫ Flash-To-Pass ........................ .142
▫ High/Low Beam Switch ..................143
 WINDSHIELD WIPERS AND WASHERS .......143
▫ Windshield Wiper Operation ...............143
▫ Intermittent Wiper System ................144
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

▫Forward Collision Warning (FCW) With Mitigation
Operation ........................... .174
▫ Turning FCW ON Or OFF .................176
▫ Changing FCW And Active Braking Status .....176
▫ FCW Limited Warning...................177
▫ Service FCW Warning ....................177
 LANESENSE — IF EQUIPPED ..............178
▫ LaneSense Operation ....................178
▫ Turning LaneSense ON Or OFF .............179
▫ LaneSense Warning Message ...............180
▫ Changing LaneSense Status ................182
 PARKSENSE REAR PARK ASSIST —
IF EQUIPPED ......................... .183
▫ ParkSense Sensors ..................... .184
▫ ParkSense Warning Display ................184
▫ ParkSense Display ..................... .185
▫ Enabling And Disabling ParkSense ..........190
▫ Service The ParkSense Rear Park Assist System. .190 ▫
Cleaning The ParkSense System .............190
▫ ParkSense System Usage Precautions .........191
 PARKVIEW REAR BACK UP CAMERA —
IF EQUIPPED ......................... .192
 OVERHEAD CONSOLE ...................194
▫ Front Map/Reading Lights — If Equipped . . . .194
▫ Courtesy Lights ....................... .195
▫ Sunglasses Bin Door ....................196
 GARAGE DOOR OPENER — IF EQUIPPED . . . .196
▫ Before You Begin Programming HomeLink .....197
▫ Programming A Rolling Code ..............197
▫ Pr

ogramming A Non-Rolling Code ..........199
▫ Canadian/Gate Operator Programming .......200
▫ Using HomeLink ...................... .201
▫ Security ............................. .201
▫ Troubleshooting Tips ....................201
▫ General Information .....................202
92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Modes Of Operation
Three selectable modes of operation are available in the
Uconnect System. Refer to “Uconnect Settings/Customer
Programmable Features” in “Understanding Your Instru-
ment Panel” for further information.
Blind Spot Alert Lights Only (Default Setting)
When operating in Blind Spot Alert mode, the BSM system
will provide a visual alert in the appropriate side view
mirror based on a detected object. However, when the
system is operating in Rear Cross Path mode, the system
will respond with both visual and audible alerts when a
detected object is present. Whenever an audible alert is
requested, the radio volume is reduced.
Blind Spot Alert Lights/Chime
When operating in Blind Spot Alert Lights/Chime mode,
the BSM system will provide a visual alert in the appro-
priate side view mirror based on a detected object. If the
turn signal is then activated, and it corresponds to an alert
present on that side of the vehicle, an audible chime will
also be sounded. Whenever a turn signal and detected
object are present on the same side at the same time, both
the visual and audio alerts will be issued. In addition to the
audible alert the radio (if on) volume will be reduced.NOTE:
•
Whenever an audible alert is requested by the BSM
system, the radio volume is reduced.
• If the hazard flashers are on, the system will request the
appropriate visual alert only.
When the system is in RCP, the system shall respond with
both visual and audible alerts when a detected object is
present. Whenever an audible alert is requested, the radio
volume is reduced. Turn/hazard signal status is ignored;
the RCP state always requests the chime.
Blind Spot Alert Off
When the BSM system is turned off there will be no visual
or audible alerts from either the BSM or RCP systems.
NOTE: The BSM system will store the current operating
mode when the vehicle is shut off. Each time the vehicle is
started the previously stored mode will be recalled and
used.
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

You can choose from HI, LO or OFF heat settings. Amber
indicator lights in each switch indicate the level of heat in
use. Two indicator lights will illuminate for HI, one for LO
and none for OFF.Push the switch once to select HI-level heating.
Push the switch a second time to select LO-level
heating. Push the switch a third time to shut the
heating elements OFF.
When the HI-level setting is selected, the heater will
provide a boosted heat level during the first four minutes
of operation. Then, the heat output will drop to the normal HI-level. If the HI-level setting is selected, the system will
automatically switch to LO-level after approximately 60
minutes of continuous operation. At that time, the number
of indicator lights changes from two to one, indicating the
change. The LO-level setting will turn OFF automatically
after approximately 45 minutes.
NOTE:
•
Once a heat setting is selected, heat will be felt within
two to five minutes.
• The engine must be running for the heated seats to
operate.WARNING!
• Persons who are unable to feel pain to the skin
because of advanced age, chronic illness, diabetes,
spinal cord injury, medication, alcohol use, exhaus-
tion or other physical condition must exercise care
when using the seat heater. It may cause burns even
at low temperatures, especially if used for long
periods of time.
• Do not place anything on the seat or seatback that
insulates against heat, such as a blanket or cushion.
(Continued)
Rear Heated Seat Switches
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117

LIGHTS
Headlight Switch
The headlight switch is located on the left side of the
instrument panel, next to the steering wheel. The headlight
switch controls the operation of the headlights, parking
lights, instrument panel lights, cargo lights and fog lights
(if equipped).To turn on the headlights, rotate the headlight
switch clockwise. When the headlight switch is
on the parking lights, taillights, license plate light
and instrument panel lights are also turned on.
To turn off the headlights, rotate the headlight switch back
to the O (OFF) position.
NOTE:
• Your vehicle is equipped with plastic headlight and fog
light (if equipped) lenses that are lighter and less sus-
ceptible to stone breakage than glass lights. Plastic is not
as scratch resistant as glass and therefore different lens
cleaning procedures must be followed.
• To minimize the possibility of scratching the lenses and
reducing light output, avoid wiping with a dry cloth. To
remove road dirt, wash with a mild soap solution
followed by rinsing.
CAUTION!
Do not use abrasive cleaning components, solvents, steel
wool or other abrasive materials to clean the lenses.
Headlight Switch
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135

Automatic Headlights
This system automatically turns the headlights on or off
according to ambient light levels. To turn the system on,
rotate the headlight switch counterclockwise to the AUTO
position. When the system is on, the headlight time delay
feature is also on. This means the headlights will stay on
for up to 90 seconds after you place the ignition into the
OFF position. To turn the automatic system off, move the
headlight switch out of the AUTO position.
NOTE:The engine must be running before the headlights
will come on in the automatic mode.
Headlights On Automatically With Wipers
If your vehicle is equipped with Automatic Headlights, it
also has this customer-programmable feature. When your
headlights are in the automatic mode and the engine is
running, they will automatically turn on when the wiper
system is on. This feature is programmable through the
Uconnect system. Refer to “Uconnect Settings/Customer
Programmable Features” in “Understanding Your Instru-
ment Panel” for further information. NOTE:
When your headlights come on during the day-
time, the vehicle will monitor outside brightness and
decide if the instrument panel needs to be dimmed or not.
Refer to “Lights” in this section for further information.
Automatic High Beam — If Equipped
The Automatic High Beam Headlamp Control system
provides increased forward lighting at night by automat-
ing high beam control through the use of a digital camera
mounted on the inside rearview mirror. This camera de-
tects vehicle specific light and automatically switches from
high beams to low beams until the approaching vehicle is
out of view.
NOTE:
• The Automatic High Beam Headlamp Control can be
turned on or off using the Uconnect System. Refer to
“Uconnect Settings” in “Understanding Your Instrument
Panel” for further information.
• Broken, muddy, or obstructed headlights and taillights
of vehicles in the field of view will cause headlights to
remain on longer (closer to the vehicle). Also, dirt, film,
and other obstructions on the windshield or camera lens
will cause the system to function improperly.
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

•To opt out of the Advanced Auto High-Beam Sensitivity
Control (default) and enter Reduced High-Beam Sensi-
tivity Control (not recommended), toggle highbeam
lever 6 full on/off cycles within 10 seconds of ignition
ON. System will return to default setting upon ignition
off.
If the windshield or Automatic High Beam Headlamp
Control mirror is replaced, the mirror must be re-aimed to
ensure proper performance. See your local Authorized
Dealer.
Daytime Running Lights — If Equipped
The Daytime Running Lights come on whenever the en-
gine is running, and the transmission is not in the PARK
position. The lights will remain on until the ignition is
switched to the OFF or ACC position or the parking brake
is engaged. The headlight switch must be used for normal
nighttime driving.
NOTE: If allowed by law in the country in which the
vehicle was purchased the Daytime Running Lights can be
turned on and off using the Uconnect System, refer to
“Uconnect Settings” in “Understanding Your Instrument
Panel” for further information.
Headlight Delay
To aid in your exit, your vehicle is equipped with a
headlight delay that will leave the headlights on for
approximately 90 seconds. This delay is initiated when the
ignition is turned OFF while the headlight switch is on, and
then the headlight switch is cycled off. Headlight delay can
be cancelled by either turning the headlight switch on then
off, or by turning the ignition ON.
NOTE: The headlight delay time is programmable through
the Uconnect System. Refer to “Uconnect Settings/
Customer Programmable Features” in “Understanding
Your Instrument Panel” for further information.
Parking Lights And Panel Lights
To turn on the parking lights and instrument panel
lights, rotate the headlight switch clockwise. To turn
off the parking lights, rotate the headlight switch back to
the O (Off) position.
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137

Fog Lights — If Equipped
The fog lights are turned on by rotating the headlight
switch to the parking light or headlight position and
pushing in the headlight rotary control.
The fog lights will operate only when the parking lights are
on or when the vehicle headlights are on low beam. An
indicator light located in the Instrument Cluster Display
will illuminate when the fog lights are on. The fog lights
will turn off when the switch is pushed a second time,
when the headlight switch is rotated to the off position, or
the high beam is selected.
Interior Lights
Courtesy and dome lights are turned on when the front
doors are opened or when the dimmer control (rotating
wheel on the right side of the headlight switch) is rotated
to the its farthest upward position. If your vehicle is
equipped with Remote Keyless Entry and the UNLOCK
button is pushed on the key fob, the courtesy and dome
lights will turn on. When a door is open and the interior
lights are on, rotating the dimmer control all the way
down, to the OFF detent, will cause all the interior lights to
go out. This is also known as the “Party” mode because it
allows the doors to stay open for extended periods of time
without discharging the vehicle’s battery.
Fog Light Operation
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE