2017 Citroen GRAND C4 PICASSO clock

225
C4-Picasso-II_en_Chap05_eclairage-visibilite_ed02-2016
Screenwash and washer jets
Windscreen wash and headlamp wash
Adjusting the jets
The front washers include an adjustment for the
height of delivery from the jets.
If you want to modify the factory setting, turn
the screw on each jet anti-clockwise, towards
the "+" to raise the jet or clockwise, towards
the "-" to lower it.
Headlamp wash
F Pull the windscreen wiper stalk towards you. The windscreen wash then the
windscreen wipers operate for a fixed
period.
A few moments after releasing the wiper stalk,
there is a last wipe to clear any runs from the
screen. The headlamps operate when the vehicle is
moving and when the dipped beam headlamps
are on. However, to reduce the consumption
of screenwash fluid, the headlamp wash only
operates with every 7th use of the screenwash
or once every 25 miles (40 km), during a given
j o u r n ey.
5
Lighting and visibility

284
C4-Picasso-II_en_Chap07_info-pratiques_ed02-2016
Recommendations on storage
AdBlue® freezes at about -11°C and
deteriorates above 25°C. It is recommended
that bottles be stored in a cool area and
protected from direct sunlight.
Under these conditions, the fluid can be kept
for at least a year.
If the additive has frozen, it can be used once it
has completely thawed out.
Procedure
Before topping-up, ensure that the vehicle is
parked on a flat and level sur face.
In wintry conditions, ensure that the
temperature of the vehicle is above -11°C.
Other wise, by freezing, the AdBlue
® cannot
be poured into its tank. Park your vehicle in a
warmer area for a few hours to allow the top-up
to be carried out.
F

P

ress the START/STOP button to switch
off the engine. F
F or access to the AdBlue® tank, raise the
boot floor, or on 7-seat versions, unfold the
right hand seat in the third row.
Never store bottles of AdBlue
® in your
vehicle.
F

W
ithout pressing, turn the black cap a
quarter turn anti-clockwise and lift it off.
F

T
urn the blue cap a 6
th of a turn anti-
clockwise.
F

L

ift off the cap.
F

O

btain a bottle of AdBlue
®. After first
checking the use-by date, read carefully
the instructions on use on the label before
pouring the contents of the bottle into your
vehicle's AdBlue
® tank.
Practical information

285
C4-Picasso-II_en_Chap07_info-pratiques_ed02-2016
Important: if your vehicle's AdBlue®
tank is completely empty - which is
confirmed by the alert messages and
the impossibility of starting the engine,
you must add at least 3.8 litres of fluid. Important:
when topping-up after
running out of AdBlue®, signalled
by the message "Top-up AdBlue:
Starting prevented", you must wait
for approximately 5 minutes before
switching on the ignition, without
opening the driver's door, unlocking
the vehicle, placing the key of the
"Keyless Entr y and Star ting" system
inside the vehicle or inser ting the
electronic key in the reader.
Switch on the ignition, wait for
10

seconds, then start the engine.
If any fluid is spilt or splashed, wash
immediately with cold water or wipe with
a damp cloth.
If the fluid has crystallised, clean it off
using a sponge and hot water.
F

A

fter emptying the bottle, wipe away any
spillage around the tank filler using a damp
cloth. F

R

efit the blue cap to the tank and turn it a
6th of a turn clockwise, to its stop.
F
R
efit the black cap and turn it a quarter of
a turn clockwise without pressing. Ensure
that the indicator on the cap lines up with
the indicator on the support.
F

D

epending on equipment, return the spare
wheel and/or the storage box to the bottom
of the boot.
F

R

efit the boot carpet and close the tailgate.
Do not dispose of AdBlue
® bottles or
containers in the household waste.
Place them in a container provided
for this purpose or take them to your
dealer.
7
Practical information

292
C4-Picasso-II_en_Chap08_en-cas-panne_ed02-2016
Removing the pipe and cartridge
F Turn the pipe assembly 2 to the left until it contacts the unit.
F

D
isconnect the union 1 from the cartridge
by turning it a quarter turn anti-clockwise.
F

E
xtract the pipe assembly 2 , then
disconnect the union 3 from the air
delivery
pipe by turning it a quarter turn
anti-clockwise.
F

R
emove the pipe assembly 2 .
F

S
upport the compressor vertically.
F

U
nscrew the cartridge 4 from the bottom.
To fit the new cartridge and new pipe, carry out
these operations in reverse order. Beware of discharges of fluid.
The expiry date of the fluid is indicated
on the cartridge.
The sealant cartridge is designed for
single use; even if only partly used, it
must be replaced.
After use, do not discard the cartridge
into the environment, take it to an
authorised waste disposal site or a
CITROËN dealer.
Do not forget to obtain a new sealant
cartridge, available from CITROËN
dealers or from a qualified workshop.
In the event of a breakdown

297
C4-Picasso-II_en_Chap08_en-cas-panne_ed02-2016
Taking out the spare wheel
The spare wheel is supported by a carrier
underneath the vehicle.
Access to the spare wheel*
F Take out the wheel / tool box assembly from the rear of the vehicle.
F

S
traighten the spare wheel for access to
the tools ( A).
F

F

old the concertina board and put the left
hand third row seat into position (if your
vehicle has them).
F

R

aise the pre-cut section of carpet to
expose the nut for operating the spare
wheel carrier.
F

U

sing the extension 6 fitted to the end of
the wheelbrace 1 , turn the nut clockwise
to unwind the carrier cable until the spare
wheel reaches the ground. Unwind the
length needed for access to the wheel.
Only a "space-saver" type of spare
wheel can be fitted under the vehicle.
* Depending on version. F

D
etach the link piece from the tool
box
lid (B - C ).
F

P
ass the link piece through the middle of
the wheel to free it ( D).
8
In the event of a breakdown

298
C4-Picasso-II_en_Chap08_en-cas-panne_ed02-2016
A punctured wheel from the vehicle
cannot be fitted under the vehicle. It
must be carried in the boot. Use a cover
to protect the boot.
F
P
ress the tongue, slide the tool box cover
to the centre and remove it for access to
the other tools ( jack and wheel bolt cover
remover for alloy wheels).
Putting the carrier and spare
wheel back in place
F Stow the corresponding tools in the box and close the cover.
F

P
osition the tool box on the ground.
Stowing the tools
F Return the tools to the box and stow the box in the vehicle's boot.
F

W
ind in the carrier by turning the
wheelbrace clockwise: once the cable is
fully wound in you should no longer feel
any resistance.
F

S
tow the other tools in the locations
provided in the boot.
When the spare wheel is fitted in place
of a punctured wheel, it is essential
to return the carrier and tools to their
normal position under the vehicle
before moving off.
In the event of a breakdown

299
C4-Picasso-II_en_Chap08_en-cas-panne_ed02-2016
F Insert the link piece in the aperture in the tool box ( B - C). F

I
nsert the centre guide into the middle of
the wheel.
F
P
lace the wheel / tool box assembly under
the rear of the vehicle.
F
C
entre and position the spare wheel on the
tool box ( D). F

R
aise the wheel / tool box assembly
underneath the vehicle by turning the
carrier drive nut anticlockwise using the
wheelbrace and the extension.
F
T
ighten fully. When the cable is fully wound
in, rotation of the nut no longer presents
any resistance.
F
C
heck that the wheel is horizontally flat
against the floor.
F
S
traighten the wheel.
F
P
ass the link piece through the middle of
the wheel ( A).
8
In the event of a breakdown

307
C4-Picasso-II_en_Chap08_en-cas-panne_ed02-2016
The direction indicator bulb is located below
the front lamp.
F
T
urn the bulb holder a quarter turn anti-
clockwise.
F

R
emove the bulb holder.
F

C
hange the failed bulb.
For reassembly, carry out these operations in
reverse order.
Direction indicators Front foglamps
F Unclip the finisher by pulling at the top.
F
R emove the two screws to remove the unit.
F

T
urn the bulb holder a quarter turn.
F

R
emove the bulb holder.
F

C
hange the failed bulb.
For reassembly, carry out these operations in
reverse order, pressing on the finisher to refit it.
Faster flashing of a direction indicator
warning lamp (left or right) indicates a
failed bulb on that side.
Direction indicators
(light- emitting diodes - LED)
For the replacement of this type of lamp,
contact a CITROËN dealer or a qualified
workshop.
8
In the event of a breakdown