2017 Citroen C ZERO RHD bonnet

.
Driving recommendations 87
S tarting - stopping the vehicle
8
8
Parking brake

8
9
Drive selector

9
0
Under-inflation detection
9

2
Charging the main battery

9
7
Bonnet
10

6
Front compartment

1
07
Rear compartment

1
08
Checking levels

1
09
Checking components

1
11
Changing a wiper blade

1
12
Precautions for washing

1
1212 V battery
1 13
Temporary puncture repair kit 1 17
Spare wheel

1
21
Snow chains

1
25
Changing a bulb

1
26
Changing a fuse

1
34
Towing the vehicle

1
39
Motor and main battery

1
40
We i g h t s
1

41
Dimensions
1

42
Identification markings
1

43Audio system / Bluetooth
1 45
KENWOOD - KDC-X7000DAB 1 63
Driving
Practical information In the event of a breakdown
Technical data Audio and telematics
Alphabetical index
C

6
Electric windows 30
Dashboard fuses
1
34-136
Ventilation
4

1-42
Heating
4

3- 45
Air conditioning

4

3 - 45
Front demist / defrost

4

6
Rear screen demist /
defrost

4

6
12 V accessory socket
3
9
Parking brake

8

9
Rear view mirror

3

7
USB Player

4

0 Opening the bonnet

1
06
Instruments and controls
Opening the charging flaps 3
1
Audio system

1

45 -162
Drive selector

9

0 -91
Over view

8
Technical data - Maintenance
Front compartment 107
Checking levels 1 09 -110
-

1
2 V battery electrolyte
-

b
rake fluid
-

h
eating system fluid
-

s
creenwash fluid
Checking components

1
11
Changing front bulbs

1

26 -131
12 V battery

1

13 -116 Opening the bonnet

1
06
Electric motor

1
40We i g h t s
1

41
Rear compartment

1
08
Checking the coolant l e v e l
11

0
Front compartment f uses
13

4, 137-13 8 Dimensions
1

42
Identification markings
1

43
Over view

100
This type of control unit that has a system for
recognising the type of power point (depending
on country). It detects the power rating of your
domestic power point and is able to support
and select the best current rating to ensure
safe charging:
-
14
A (FAST): if your electrical installation
supports it.
-

8 A
(NORMAL): if your electrical
installation is standard. As a safety measure, the motor will
not start when the charging cable is
connected to the vehicle's socket.
Also, any attempt to start the motor
interrupts the charging procedure. It will
then be necessary to disconnect and
reconnect the charging cable plug to
continue charging.
The charge lamp in the instrument panel going
off and flashing of the green CHARGING lamp
indicate that charging is complete.
F

P
ress the button to remove the charging
plug.
F

R
efit the protective cover to the charging
cable.
F

C
lose the charging socket cover, then the
flap.
F

D
isconnect the charging cable from the
power point.
F

S
tow the charging cable in the bag
provided. If the 12 V battery is discharged, it is not
possible to charge the main battery.
While charging, do not do anything
under the bonnet, even with the ignition
off, as the cooling fan may start at any
time (risk of injury).
You must wait for at least one hour
after the end of the charging procedure
before doing anything under the bonnet,
as some areas may be extremely hot
(risk of burns).
Practical information

106
BonnetProtects the components in the front compartment and provides access for checking levels, charging the 12 V battery, changing fuses, etc.
F
P
ush the exterior safety catch B to the left
and raise the bonnet. F

O
pen the bonnet fully and on the right,
unclip the stay C from its holder.
F

F
it the stay C in one of the two notches to
hold the bonnet open.
F

O
pen the front right door.
F

P
ull the interior release lever A , located at
the bottom of the door aperture.
Opening Closing
F Take the stay out of the support notch.
F
C lip the stay in its housing.
F

L
ower the bonnet and release it at the end
of its travel.
F

P
ull on the bonnet to check that it is fully
latched.
Do not press down on the middle of
the bonnet if it does not fully close, as
there is a risk of deforming it. Open the
bonnet fully and close it again.
The location of the interior release lever
prevents opening of the bonnet while
the front right door is closed.
Practical information

112
Changing a wiper
blade
Removing a front or rear
wiper blade
F Raise the corresponding wiper arm.
F R emove the wiper blade, sliding it towards
the outside.
Fitting a front or rear wiper
blade
F Put the new wiper blade in place and secure it.
F

F
old down the wiper arm carefully.
Precautions for
washing
To avoid damaging the electrical
components, the use of a high pressure
jet wash is strictly prohibited:
-

i
n the front compartment (under the
bonnet).
-

u
nder the body.
For washing the bodywork, do not use a
pressure greater than 80 bars. Check - before washing the vehicle -
that the charging flaps and the charging
socket covers (normal and fast charge)
are properly closed. Do not wash the vehicle while the
battery is being recharged.
Practical information

113
12 V battery
All of the electrical components of your vehicle
(other than the electric motor, the heating and
the air conditioning) are powered by this 12 V
ancillaries battery.
It is located in the front compartment and is
recharged by the main battery, during phases
of operation ("Ready" lamp on in the instrument
panel) and charging.If the 12 V battery is discharged, it will
not be possible to start the motor and
the main battery cannot be charged. F

O
pen the front bonnet using the interior
release lever, then the exterior safety
catch.
F

S
ecure the bonnet stay.
F

S
lacken the nut 1.
F

R
emove the battery protective cover for
access to the two terminals.Access to the battery
Disconnecting the battery is not
recommended.
However, if the vehicle is not to be used
for a prolonged period of more than a
month, it may be necessary, in winter,
to disconnect and store the battery to
avoid the electrolyte freezing.
After prolonged disconnection of the
battery, you must contact a CITROËN
dealer or a qualified workshop to have
the electronic control unit reinitialised.
8
In the event of a breakdown

127
F Lift the cover B, using a screwdriver
protected by a cloth.
F

S
lacken fixing screw C until the head of the
screw touches the trim. F
R emove the bumper retaining clips, using a
screwdriver.
F

C
arefully lift the bumper.
To replace a failed bulb, you must first remove
the lamp.
To remove the lamp:
F

O

pen the bonnet.
F

P

ress tab A to release the connector.
Access to bulbs
8
In the event of a breakdown