2017 Citroen C ZERO lock

28
C-Zero_en_Chap02_ouvertures_ed01-2016
Doors
From outside
F After unlocking the vehicle using the remote control or the key, pull the door
handle.
From inside
F Pull the front or rear door control to open the door.
If the doors are locked:
-

o
pening the driver's door unlocks the other
doors,
-

t
he front passenger or rear doors must
then be unlocked manually using the front
locking control before they can be opened.
If a door or the boot is not closed
correctly, this warning lamp comes on
in the instrument panel until the door
in question or the boot is closed.
Opening
ClosingLocking/ unlocking from
the


inside
F Press the button on the driver's door
towards the front to lock and towards the
rear to unlock the vehicle completely.
The buttons on the front and rear
passenger doors only lock / unlock the
door in question.
Access

29
C-Zero_en_Chap02_ouvertures_ed01-2016
Boot
Opening
F After unlocking the vehicle using the remote control or the key, press the
handle


A and open the tailgate. F
P ull the handle B downwards to guide the
tailgate down,
F

r
elease the handle and press the exterior
sur face of the tailgate gently to close it.
Closing
2
Access

36
C-Zero_en_Chap03_ergonomie-et-confort_ed01-2016
Mirrors
Adjustment
The mirrors can be adjusted when the ignition
switch is in the "ON" or "ACC" position.
F
M
ove control A to the right or to the left to
select the corresponding mirror.
F

D
irect control B in all four directions to
adjust the mirror.
When adjustment is complete, return control A
to the central position.
Door mirrors
The mirrors can also be folded
manually.
However, you must never unfold them
manually , other wise the mirrors may
not remain in place correctly when
driving.
Always use control C to unfold them.
Electric folding / unfolding*
F With the ignition switch in the "ON" or "ACC" position: press control C to unfold
them
F

W
ith the ignition switch in the "LOCK"
position: press control C within
30


seconds to fold them.
* Depending on version.
Ease of use and comfort

47
C-Zero_en_Chap03_ergonomie-et-confort_ed01-2016
Remote control*
This is used for remote control of the following
functions:
-
C
heck of the vehicle charge status.
-

P
rogramming of charging: start time and
duration of charging.
-

A
ctivation of the climate control functions
(heating, air conditioning, demisting).
In order to programme charging, the
following conditions must be met.
-

P
lace the drive selector in
position


P.
-

P
lace the switch on LOCK .
-

C
onnect the vehicle using the
normal charging cable.Buttons Display
1. On/Off, transmission of data.
2. M
ODE: used to scroll through the various
functions available (start of charging,
duration of charging, interior temperature).
3.
I

mmediate charging of the vehicle
(resetting of the programming values to
ze r o).
4.
S

ettings. 1.
D

ata transmission status indicator lamp.
2.
C

harging indicator lamp.
3.
F

ault warning lamp.
4.
B

attery charge status warning lamp.
5.
C

harging programming functions status
indicator lamp.
6.
C

harging time remaining indicator.
7.
I

nterior temperature function status
indicator lamp.
The remote control has a range of
approximately 100 metres.
* Depending on equipment.
3
Ease of use and comfort

49
C-Zero_en_Chap03_ergonomie-et-confort_ed01-2016
In order to programme the heating, air
conditioning or demisting functions, the
following conditions must be met.
-
T
he drive selector is in position P .
-

T
he switch is on LOCK .
-

T
he vehicle is connected using the
normal charging cable.
-

A
ll of the doors are closed correctly.
-

T
he battery charge level is
sufficient (one bar minimum).
Cancelling the programmed
settings
Using the remote control
Using the switch
Place the vehicle's switch in the ON position
then return it to the LOCK position.
Programming the interior temperature
Activation of the functions
Switch on the remote control.
Press the MODE button to select the interior
temperature programming.
This function is used to programme the
switching on of:
- t
he heating.
-

t

he air conditioning.
-
t

he demisting.
Press the immediate charging button,
then press the on/off button briefly to
transmit the data to the vehicle.
One of these symbols is displayed on the
screen. It indicates the current status of the
interior temperature.
Use the arrows to select the function required.
Press the on/off button briefly to transit the data
to the vehicle.
The progammed values set using
the remote control are cancelled
automatically each time the vehicle is
started.
For maximum effectiveness of
the programming of the interior
temperature, ensure that all of the
vehicle's windows are closed.
3
Ease of use and comfort

51
C-Zero_en_Chap03_ergonomie-et-confort_ed01-2016
Operating faults
Remote control
Indicator lampsStatus CausesActions / Observations
Flashes within approximately 10 seconds
after the remote control is switched on. A fault has occurred.
Switch the remote control off, then on
again.
Flashes within approximately 1 second
after the remote control is switched on. Electrical inter ference is preventing the
operation of the remote control or the
transmission of data.Move away from the sources of
interference.
Flashes within approximately 10 seconds
after the remote control is switched on. The aerial has not been extended. Extend the aerial.
The range of the remote control has
been exceeded.Move closer to the vehicle.
The switch is not in the LOCK position. Place the switch in the LOCK position.
3
Ease of use and comfort

55
C-Zero_en_Chap04_eclairage-et-visibilite_ed01-2016
Direction indicators
F Left: lower the lighting stalk, passing the point of resistance.
F

R
ight: raise the lighting stalk, passing the
point of resistance.
Daytime running lamps
Special daytime lighting so that the vehicle can
be seen more easily.
The daytime running lamps come on
automatically when starting the motor, if no
other lighting is on.
They cannot be deactivated.Automatic illumination of headlamps
With the main lighting control ring in the AUTO
position, the sidelamps and dipped beam headlamps
come on automatically, without any action by the
driver, when a low level of ambient light is detected.
When the light returns to a sufficient level or the
wipers are switched off, the lighting is switched off
automatically.
The sensor is located at the base of the windscreen.
Automatic illumination of
headlamps
Automatic lighting off
When the lighting stalk is in the
"AUTO" position, if the ignition switch is in
the "LOCK" or "ACC" position or if the key
has been removed, the lighting switches off
automatically when the driver's door is
opened .
Although these lamps are located in
the same unit as the front foglamp, they
operate with a specific bulb.
Their use is covered by road vehicle
lighting regulations.
In foggy weather or in snow, the
sunshine sensor may detect sufficient
light. The lighting will not come on
automatically.
Do not cover the sunshine sensor, the
associated functions will no longer be
controlled.
4
Lighting and visibility

57
C-Zero_en_Chap04_eclairage-et-visibilite_ed01-2016
Rear wiper
Park.
Intermittent wipe.
The wiper wipes twice then switches to
intermittent mode with an interval of a few
seconds. Wipe with screenwash
Keep the ring in this position to operate the
screenwash with several wipes of the wiper. C.
R

ear wiper selection ring.
Courtesy lamp
Position 1 "ON"
The courtesy lamp is permanently on.
Position 2 "●"
The courtesy lamp comes on when opening
a door or the boot; when the door or boot is
closed again, the lighting gradually dims for a
few seconds before going off.
However, the courtesy lamp is switched off
immediately when the doors and boot are
closed and you lock the vehicle from the inside
or using the remote control.
Position 3 "OFF"
The courtesy lamp is permanently off. Before leaving the vehicle, ensure that
the courtesy lamp is not on.
If left on, it discharges the 12 V battery,
even if the main battery is charged or
on charge.
Starting your vehicle will then no longer
be possible.
4
Lighting and visibility