2017 CITROEN C-ELYSÉE boot

139
C-elysee_en_Chap09_info-pratiques_ed01-2016
F Obtain  a   bottle   of   AdBlue®. After first c
hecking
 
the
 
use-by
 
date,
  read   carefully  
t

he instructions on use on the label before
pouring
 
the
 
contents
 
of
 
the   bottle   into   your  
v

ehicle's
 Ad

Blue
® tank. F  
A
fter   emptying   the   bottle,   wipe   away   any  
s

pillage   around   the   tank   filler   using   a   damp  
c

loth.
F  
R
efit   the   blue   cap   to   the   tank   and   turn   it   a  
6th of a turn clockwise, to its stop.
F
 R
efit   the   plastic   blanking   plug,   clipping   it   in  
t

he   orifice.
F
 
R

eturn   the   storage   box   containing   the   tools  
t

o
  its   location.
F
 
R

efit   the   boot   floor   and   close   the   boot.
Important:
 
if
 
your
 
vehicle's
 
AdBlue
® tank i
s
 
completely
 
empty
 
-
 
which
 
is
 
c

onfirmed
 
by
 
the
 
alert
 
displays
 
and
  the  
i

mpossibility
 
of
 
starting
 
the
 
engine
 
-  
you
 
must
 
add
 
at
 
least
 
3.8
 
litres
 

(so
 
two
 
1.89
 
litre
 
bottles). If
  any   additive   is   split   or   splashed,   wash  
i

mmediately  
w
ith  
c
old  
w
ater  
o
r  
w
ipe  
w
ith  
a

  damp   cloth.
If   the   additive   has   crystallised,   clean   it  
o

ff   using   a   sponge   and   hot   water.Important:
 i
n the event of a top-up after
a breakdown because of a lack of
additive ,   you   must   wait   around   5 minutes
 b

efore   switching   on   the   ignition,   without
opening the driver's door, locking the
vehicle or introducing the key into the
ignition switch .
Switch   on   the   ignition,   then,   after
 1

0 seconds,   start   the   engine.
Never   dispose   of   AdBlue
® additive b
ottles
 
in
 
the
 
household
 
waste.   Place  
t

hem
 
in
 
a
 
special
 
container   provided  
t

his
 p

urpose
 o

r
 t

ake
 t

hem
 t
o
 y
our
 d
ealer.
9
Practical information

145
C-elysee_en_Chap09_info-pratiques_ed01-2016
Spare wheel
The tools are installed in the boot under the fl o o r.
To
  gain   access   to   them:
F

o
pen the boot,
F
 
l
ift   the   floor   and   remove   it.
F
 
r
emove   the   storage   box   containing   the  
to

ols.
Access to the tools
List of tools
Procedure for changing a wheel with a punctured tyre for the spare wheel using the tools provided with the vehicle.
T hese   tools   are   specific   to   your   vehicle   and  
c

an   vary   according   to   the   level   of   equipment.  
D

o   not   use   them   for   any   purpose   other   than  
d

etailed
 belo
w.
1.
 W

heelbrace.
 F

or   removing   the   wheel   trim   and   removing  
t

he   wheel   bolts.
2.
 J

ack   with   integral   handle.
 F

or   raising   the   vehicle.
3.
 W

heel   bolt   cover   removal   tool.
 F

or   removing   the   wheel   bolt   cover   on   alloy  
w

heels.
4.
 T

owing   eye.
For
  more   information   on   towing,   refer   to   the  
c

orresponding
 s
ection.
The
  jack   must   only   be   used   to   change   a  
w

heel   with   a   damaged   tyre.
The
  jack   does   not   require   any  
m

aintenance.
The
  jack   conforms   to   European  
l

egislation,   such   as   defined   in   the  
M

achinery   Directive   2006/42/CE.
9
Practical information

146
C-elysee_en_Chap09_info-pratiques_ed01-2016
The spare wheel is installed in the boot under the   floor.
Depending
  on   engine,   the   spare   wheel   is  
a

  standard   wheel   or   the   space-saver   type  
(

BlueHDi   100).
Access to the spare wheel
Taking out the wheel
F Unclip   the   tool   storage   box   (standard   spare  w
heel).
F
 
U
nscrew   the   central   nut.
F
 
R
emove   the   fixing   parts   (nut   and   bolt).
F
 
R
aise   the   spare   wheel   towards   you   from  
t

he   rear.
F
 
T
ake   the   wheel   out   of   the   boot.
Pr

150
C-elysee_en_Chap09_info-pratiques_ed01-2016
F Remove  the   bolts   and   store   them   in   a   clean  p
lace.
F
 
R
emove   the   wheel.
Fitting a wheel
Fitting the spare wheel
If your vehicle is fitted with alloy wheels, when   tightening   the   bolts   on   fitting,   it   is  
n

ormal  
t
o  
n
otice  
t
hat  
t
he  
w
ashers  
d
o  
n
ot  
c

ome   into   contact   with   the   spare   wheel.  
T

he   wheel   is   secured   by   the   conical  
s

ur face   of   each   bolt.
After changing a wheel
When using a "space-saver" type of spare   wheel,   do   not   exceed   50   mph  
(80
  km/h).
Have
  the   tightening   of   the   bolts   and   the  
p

ressure   of   the   spare   wheel   checked  
b

y   a   CITROËN   dealer   or   a   qualified  
w

orkshop   without   delay.
Have
  the   punctured   wheel   repaired  
a

nd   refitted   to   the   vehicle   as   soon   as  
p

ossible.
Stowing the wheel with
punctured tyre
The wheel with punctured tyre can be stowed   under   the   floor,   in   the   housing  
f

or   the   standard   spare   wheel.
To
  stow   an   alloy   wheel,   first   remove   the  
t

rim  
f
rom  
t
he  
m
iddle  
o
f  
t
he  
w
heel  
s
o  
t
hat  
t

he   fixing   parts   (nut   and   bolt)   can   be   put  
i

n   place.
In
  the   case   of   a   "space-saver"   type  
s

pare   wheel,   the   wheel   with   punctured  
t

yre   cannot   be   stowed   under   the   floor.   It  
m

ust   be   stowed   in   the   boot;   use   a   cover  
t

o   protect   the   inside   of   the   boot.
Practical information

157
C-elysee_en_Chap09_info-pratiques_ed01-2016
Changing bulbs
These bulbs are changed from inside the boot:
F
o
pen the boot,
F
 
r
emove   the   access   grille   from   the  
c

orresponding   side   trim   panel,
F
 
s
lacken   and   remove   the   nut,
F
 
d
isconnect   the   lamp   unit   connector,
F
 
u
nclip   the   lamp   unit   by   lowering   the   tongue  
a

nd   carefully   extract   it   pulling   in   line  
t

owards   the   outside, F
 
r
emove   the   four   screws   and   lift   off   the   bulb  
h

o l d e r,
F
 
t
urn   the   failed   bulb   a   quarter   of   a   turn   and  
c

hange
 it
.
To refit, carry out these operations in reverse
o r d e r.
Take
  care   to   engage   the   lamp   unit   in   its   guides,  
w

hile   keeping   it   in   line   with   the   vehicle.
Tighten
  sufficiently   to   ensure   sealing,   but  
w

ithout
 d
amaging
 t
he
 lam
p.
1.
D

irection indicators (PY21W amber).
2. R
eversing lamps (R10W).
3. F
oglamp (P21W).
4.
S

idelamps (P21/5W).
5.
B

rake lamps

/ sidelamps (P21/5W).
Rear lamps
9
Practical information

167
C-elysee_en_Chap09_info-pratiques_ed01-2016
Disconnecting the (+) terminal
F Raise the lever A fully to release the clamp  B.
Reconnecting the (+) terminal
F Position   the   open   clamp   B of the cable on
the   positive   post   (+)   of   the   battery.
F
 
P
ress   down   on   the   clamp   to   position   it  
c

orrectly   on   the   battery   post.
F
 
L
ock   the   clamp   by   lowering   the   lever   A.
Do
  not   force   the   lever   as   locking   will  
n

ot   be   possible   if   the   clamp   is   not  
p

ositioned   correctly;   start   the   procedure  
ag

ain.
Disconnecting the battery
In order to maintain an adequate state of   charge   for   starting   the   engine,   it   is  
r

ecommended   that   the   battery   be   disconnected  
i

f   the   vehicle   is   taken   out   of   service   for   a   long  
p

eriod.
Wait
  2   minutes   after   switching   off   the   ignition  
b

efore   disconnecting   the   battery:
F
 
c
lose   all   openings   (doors,   boot,   windows,  
r

oof),
F
 
s
witch   off   all   electrical   consumers   (audio  
s

ystem,   wipers,   lighting,   ...),
F
 
s
witch   off   the   ignition   and   wait   for  
f

our minutes.
Having
  exposed   the   battery,   it   is   only  
n

ecessary   to   disconnect   the   (+)   terminal.
Following reconnection of the
battery
After reconnecting the battery, switch on the ignition   and   wait   1   minute   before   starting   to  
a

llow   initialisation   of   the   electronic   systems.
However,
  if   minor   problems   persist   following  
t

his   operation,   contact   a   CITROËN   dealer   or   a  
q

ualified
 w
orkshop.
Referring
  to   the   corresponding   section,   you  
m

ust   yourself   reinitialise   or   reset   certain  
s

ystems,   such   as:
-
 
t
he   remote   control,
-
 
t
he   date   and   time,
-
 
t
he   radio   preset   stations.
Quick release terminal
The Stop & Start system may not be operational   during   the   trip   following   the  
f

irst   engine   start.
In
  this   case,   the   system   will   only   be  
a

vailable   again   after   a   continuous  
p

eriod   of   immobilisation   of   the   vehicle,  
a

  period   which   depends   on   the   ambient  
t

emperature   and   the   state   of   charge   of  
t

he   battery   (up   to   about   8   hours).
9
Practical information

170
C-elysee_en_Chap09_info-pratiques_ed01-2016
Towing the vehicle
Access to the tools
The towing eye is installed in the boot under the   floor.
To
  gain   access   to   it:
F

o
pen the boot,
F
 
l
ift   the   floor   and   remove   it,
F
 
r
emove   the   towing   eye   from   the   holder.
General recommendations
Observe the legislation in force in your country.
E nsure   that   the   weight   of   the   towing   vehicle   is   higher   than   that   of   the   towed   vehicle.
The
  driver   must   remain   at   the   wheel   of   the   towed   vehicle   and   must   have   a   valid   driving  
l

icence.
When
  towing   a   vehicle   with   all   four   wheels   on   the   ground,   always   use   an   approved   towing  
a

rm;   rope   and   straps   are   prohibited.
The
  towing   vehicle   must   move   off   gently.
When
  towing   a   vehicle   with   the   engine   off,   there   is   no   longer   any   power   assistance   for  
b

raking   or   steering.
In
  the   following   cases,   you   must   always   call   on   a   professional   recovery   service:
-
 
v
ehicle   broken   down   on   a   motor way   or   fast   road,
-
 
f
our-wheel   drive   vehicle,
-
 
w
hen   it   is   not   possible   to   put   the   gearbox   into   neutral,   unlock   the   steering,   or   release  
t

he   parking   brake,
-
 
t
owing   with   only   two   wheels   on   the   ground,
-
 
w
here   there   is   no   approved   towing   arm   available...
Procedure
 
for
 
having
 
your
 
vehicle
 
towed.
Practical information

175
C-elysee_en_Chap09_info-pratiques_ed01-2016
Accessories
A wide range of accessories and genuine parts is available from the CITROËN dealer network.
T hese   accessories   and   parts   are   all   suitable   for   your   vehicle   and   benefit   from   CITROËN's  
r

ecommendation   and   warranty.
"Comfort":
door deflectors, side blinds and rear screen blind,   smoker   kit,   portable   scented   air  
f

reshener,   boot   dividers,   coat   hanger,   armrest,  
i

nsulated   module,   reading   lamp,   cruise   control,  
b

oot   storage,   front   and   rear   parking   sensors,  
g

love   box   lid...
"Transport solutions":
towbars, towbar harnesses, roof bars, bicycle
carrier on towbar, bicycle carrier on roof bars,
ski  carrier,   roof   boxes...
"Security and safety":
wheel security bolts, child seats, breathalyzer, first   aid   kit,   warning   triangle,   high   visibility   vest,  
s

now   chains,   non-slip   covers,   foglamp   kit,   fire  
e

xtinguisher...
Tow
 
bar,
 
which
 
mst
 
be
 
fitted
 
by
 
C

ITROËN
 
dealer
 
or
 
a
 
qualified
 
w

orkshop.
Advice on care an d m aintenance
Recommendations on the care and m
aintenance   your   vehicle   are   given   in   the  
m

aintenance
 an
d
 w
arranty
 g
uide.
"Styling":
gear lever knob, spoiler, parking brake lever grip,   spoiler,   alloy   wheels,   foglamp   trims,  
c

hromed   mirror   shells,   aluminium   footrest,  
c

hrome   exhaust   tailpipes,   door   sill   finishers,  
w

heel
 t
rims...
9
Practical information