28
or
Range between 0 and 350 miles (0 and 600 km)
or
Breakdown related to a lack of AdBlue
®
To be able to restart the engine, it is
essential to add at least 3.4 litres of
AdBlue
® to its tank.
For more information on AdBlue® and
the SCR (BlueHDi Diesel) system , and
in particular topping it up, refer to the
corresponding section.
When switching on the ignition, the Service
warning light comes on and the AdBlue warning
light flashes, accompanied by an audible signal
and the temporary display of "NO START IN"
and 0 miles or kilometres in the instrument
cluster - ("NO START IN 0 miles" means
"Starting prevented").
The AdBlue
® tank is empty: the starting
inhibition system required by legislation
prevents starting of the engine.
When switching on the ignition, the Service
warning light comes on and the AdBlue warning
light flashes, accompanied by an audible signal
and the temporary display of "NO START
IN" and a distance in the instrument cluster,
indicating the remaining range expressed in
miles or kilometres before engine starting
is prevented - (e.g. "NO START IN 300 km"
means "Starting will be prevented in 300 km
(186 miles).
When driving, this message is displayed every
30 seconds until the AdBlue
® level has been
topped-up.
It is essential to top-up as soon as possible and
before the tank is completely empty; other wise
it will not be possible to restart the engine after
the next stop.
For more information on AdBlue
® and the SCR
(BlueHDi Diesel) system , and in particular
topping it up, refer to the corresponding
section.
Instruments
29
In the event of a fault with the emissions control system SCR
A device preventing the engine from
starting automatically activates after
685 miles (1,100 km) of driving following
confirmation of a fault in the SCR
emissions control system. Have the
system checked by a
CITROËN dealer or a
qualified workshop as soon as possible. In the event of the detection of a fault
If it is a temporary fault, the alert
disappears during the next journey, after
self-diagnosis of the emissions SCR
system. or
If a fault with the SCR system is confirmed (after 30
miles (50 km) covered with the permanent display
of the message signalling a fault), the Service and
engine diagnostic warning lights come on and
the AdBlue warning light flashes, accompanied
by an audible signal and the temporary display in
the instrument cluster of "NO START IN" and a
distance, indicating the remaining range expressed
in miles or kilometres before engine starting is
prevented - (e.g.: "NO START IN 600 km" means
"Starting will be prevented in 600 km (375 miles).
While driving, this display appears every
30
seconds while the fault with the SCR emissions
system persists.
The alert is repeated when switching on the
ignition.
You should go to a
CITROËN dealer or a qualified
workshop as soon as possible.
Other wise, you will not be able to restart the
vehicle.
During the permitted driving phase (between
685 and 0 miles) (1,100 km and 0 km)
or
The AdBlue, Service and engine diagnostic
warning lights come on, accompanied by an
audible signal and the display of the message
"Emissions fault".
The alert is triggered when driving when the
fault is detected for the first time, then when
switching on the ignition for subsequent
journeys, while the fault persists.
1
Instruments
30
Every time the ignition is switched on, the
Service and engine diagnostic warning
lights come on and the AdBlue warning light
flashes, accompanied by the temporary
display of "NO START IN" and 0 km or miles
- ("NO
START IN 0 km" means "Starting
prevented") in the instrument cluster. Starting prevented
You have exceeded the authorised driving
limit: the starting prevention system
inhibits engine starting.To be able to start
the engine, you must call on a
CITROËN
dealer or a qualified workshop.
Distance recorders
Total distance recorder
System which measures the total distance
travelled by the vehicle during its life.
The total and trip distances are displayed for
thirty seconds when the ignition is switched off,
when the driver's door is opened and when the
vehicle is locked or unlocked.
Trip distance recorder
System which measures a distance travelled
during a day or other period since it was reset
to zero by the driver.
F
W
ith the ignition on, press the button until
zeroes appear.
or
Instruments
107
Moving off
F Select position N.
F P ress the brake pedal firmly.
F
S
tart the engine.
You must keep your foot on the brake
pedal while starting the engine.
If the engine does not start:
-
If N is flashing in the instrument panel,
move the selector to position A then to
position N .
-
I
f the “Foot on brake” message
appears, press the brake pedal
harder.
N appears in the instrument cluster.
F
Sel
ect automated mode (position A ),
manual mode (position M ) or reverse
(position R ) AUTO
and 1, 1 or R appear on the
instrument cluster.
F
R
elease the parking brake.
F
G
radually release the brake pedal.
The vehicle then moves off straight away
(refer to the section on the "Autonomous
traction function").
F
Accelerate.
Do not press the brake and clutch pedals
simultaneously. This can cause very rapid
wear on the clutch.Autonomous traction function
This function provides great flexibility in
manoeuvring the vehicle at low speed (when
parking, in traffic jams, …).
With the gear selector in position A , M or R,
the vehicle moves as soon as you take your
foot off the brake pedal , at low speed and
with the engine at idle.
When the engine is running, never leave
children in the vehicle without supervision.
The autonomous traction function may
be temporarily unavailable if the clutch
temperature is too high or the slope too
steep.
6
Driving
108
Automated mode
F Select position A.
You can change mode at any time by
moving the gear selector from A to M or
the other way round.
Moving vehicle, never select the neutral N .
The instrument cluster displays
AUTO
along with the gear engaged.
The gearbox is then operating in auto-active
mode, without any action on the part of the
driver. It continuously selects the most suitable
gear for adapted to the following parameters:
-
o
ptimisation fuel consumption,
-
t
he style of driving,
-
r
oad conditions,
-
v
ehicle load.
For optimum acceleration, when overtaking
another vehicle for example, press the
accelerator pedal fully down, beyond the point
of resistance.
Manual mode
F Select position M .
Moving vehicle, never select the neutral N .
You can change mode at any time by
moving the gear selector from M to A or
the other way round. The gears engaged appear in turn in
the instrument cluster.
The shift requests are taken into account only if
the engine speed allows.
It is not necessary to release the accelerator
when changing gear.
When braking or slowing down, the gearbox
changes down automatically to allow the
vehicle to accelerate in the correct gear.
Under full acceleration, unless the engine is
close to its maximum speed, gear upshift will
only take place when the driver operates the
gear selector.
Reverse gear
To engage reverse gear, the vehicle must be
immobilised with your foot on the brake pedal.
F
Sel
ect position R .
There is an audible signal upon
engagement of reverse.
At low speed, if reverse gear is requested, the
N indicator flashes and the gearbox goes into
neutral automatically.
To engage reverse, put the gear selector into
position N , then to position R .
Driving
109
Stopping the vehicle
Before switching off the engine, you can:
- m ove to position N to engage neutral,
or
-
l
eave the gear engaged; in this case, it will
not be possible to move the vehicle.
For all parking situations, you must apply
the parking brake to immobilise the
vehicle.
In case of immobilization of the vehicle,
engine running, absolutely put the gearbox
in neutral N .
Before working in the engine
compartment, ensure that the gear
selector is in neutral N and the parking
brake is applied.
Reinitialisation
Following disconnection of the battery, you
have to reinitialise the gearbox.
F
S
witch on the ignition.AUTO and - appear in the
instrument cluster.
F
Sel
ect position N .
F
P
ress the brake pedal.
F
W
ait for approximately 30 seconds until N
or a gear appears in the instrument cluster.
F
M
ove the gear selector to position A , then
to position N .
F
W
ith your foot still on the brake pedal, start
the engine.
The gearbox is operational again. Exceptionally, it may be necessary to
reinitialise the gearbox automatically: in
such a case the vehicle won't start and no
gear change will happen.
Malfunction
or
With the ignition on, if this warning
light comes on and AUTO
flashes,
accompanied by an audible signal
and a message in the multifunction
screen, this indicates a gearbox
fault.
Have them checked by a
CITROËN dealer or a
qualified workshop. AUTO
and - appear in the
instrument cluster.
Follow the procedure described above.
6
Driving
126
Deactivation / Activation
The function is deactivated or activated via the
vehicle configuration menu.
With audio system
In the "Personalisation -
Configuration " menu, activate/
deactivate " Parking sensors ".
With the touch screen
Press MENU.
In the " Driving / Vehicle " menu,
activate/deactivate " Parking
sensors ".
The function will be deactivated
automatically if a trailer is being towed or
a bicycle carrier is fitted (vehicle fitted with
a tow bar or bicycle carrier recommended
by
CITROËN).
Malfunction
or In the event of a system fault
when engaging the reverse gear,
this warning light is displayed in
the instrument cluster and/or a
message appears in the screen,
accompanied by an audible signal
(short beep).
Contact a
CITROËN dealer or a qualified
workshop.
In bad or wintry weather, ensure that the
sensors are not covered by mud, ice or
snow. When reverse gear is engaged, an
audible signal (long beep) indicates that
the sensors may be dirty.
Certain sound sources (motorcycle,
lorry, pneumatic drill, etc.) may trigger
the audible signals of the parking sensor
system.
Driving