2017 Citroen BERLINGO bonnet

14
Berlingo2VP_en_Chap01_vue-ensemble_ed02-2016
INSTRUMENTS AND CONTROLS
1. Lighting and direction indicator
control  stalk.
2.
 
Instrument
  panel   with   screen.
3.

Wiper
, screenwash, trip computer
control
  stalk.
4.
 
Ignition
  switch.
5.
 
Audio
  system   controls.
6.
 
Driver's
  front   airbag,   horn.
7.

Steering wheel height and reach
adjustment.
8.


Cruise control, speed limiter

controls.
9.
 
Switch
  panel,   parking   sensors,  
headlamp

  beam   adjustment,   ESC,  
Stop

  &   Start,   alarm.
10.
 
Bonnet
  release   lever.
11 .
 Electric

  door   mirror   controls.
12.
 
Electric
  window   switches.
13.
 
Switch
  panel:   hazard   warning,   central  
locking,

  child   lock.
14.
 
Cigarette
  lighter.
15.
 
Heating-ventilation
  controls.
16.

Electronic gearbox controls or Grip
control

  button.
17.
 
T
ouch   screen   tablet.
18.
 
USB
  port   (with   electronic   gearbox).
19.
 
USB
  port   (with   manual   gearbox).
Presentation

20
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Don't forget
When  leaving   the   vehicle,   check   that  
the lighting is of

f and nothing of value
is
  visible.
As a safety precaution (with children
on
  board),   remove   the   key   from   the  
ignition when leaving the vehicle, even
for

  a   short   time.
Good practice
Do not make any modifications to the electronic  immobiliser   system.
Operating the remote control, even
when
  it   is   in   your   pocket,   may   result   in  
involuntary

  unlocking   of   the   doors.
The simultaneous use of other
high frequency equipment (mobile
telephones, domestic alarms…), may
interfere with the operation of the
remote
  control   temporarily.
The remote control does not operate
while
  the   key   is   in   the   ignition,   even   if  
the

  ignition   is   off.
ELECTRONIC
IMMOBILISER
If you lose your keys
Visit a CITROËN dealer with the
vehicle's  V5   registration   certificate   and  
your

  identification   document.
A CITROËN dealer will be able
to
  retrieve   the   key   code   and  
the transponder code so that a
replacement

  key   can   be   ordered.When purchasing a second-hand
vehicle,
  have   the   keys   memorised   by  
a CITROËN dealer

, so as to be sure
that   the   keys   in   your   possession   are  
the only ones that can be used to start
the

  vehicle.
ALARM
If fitted on your vehicle, this provides two
  types   of   protection:
-
 
exterior
  protection:   it   sounds   if   a  
front/rear

  door   or   the   bonnet   is  
opened.
-

 
interior
  protection:   it   sounds   if  
the volume inside the passenger
compartment

  changes   (breaking   of  
a window or a movement inside the
vehicle).
If

 
your
 
vehicle
 
is
 
fitted
 
with
 
a
 
separation
 
partition, the interior protection is not
active

  in   the   load   space.
Locking the vehicle with
complete alarm
Setting the alarm
- Switch off the ignition and get out of
the   vehicle.
-
 
Set
  the   alarm   within   five   minutes   of  
getting

  out   of   the   vehicle,   by   locking  
or

  deadlocking   using   the   remote  
control.

 
The
  red   LED,   located   in   the  
button,

  flashes   once   per   second.
All of the keys contain an electronic immobiliser  device.
This
  device   locks   the   engine   supply  
system.

  It   is   activated   automatically  
when

  the   key   is   removed   from   the  
ignition.
After the ignition is switched on, a
dialogue

  is   established   between   the   key  
and

  the   electronic   immobiliser   system.
The
  metal   part   of   the   key   must   be  
unfolded correctly for correct dialogue
to

  take   place.
Access

55
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
The Stop & Start system
requires  a   battery   of   specific  
characteristics.

 
All
  work   on   this  
type of battery must be done only
by

 
a
  CITROËN   dealer   or   a   qualified  
workshop.
For more information on the 12 V
battery

,   refer   to   "Battery"   in   section   8.
Good practice when stopping Good practice when starting
Diesel pre-heating warning
lamp
If the temperature is high
enough, the warning lamp
comes on for less than
one second, you can start
without
  waiting.
In cold weather, wait for this warning
lamp to go off then operate the starter
(Starting position) until the engine
starts. Door or bonnet open
warning lamp
If this comes on, a door or the bonnet
is
  not   closed   correctly,   check!
Minimise engine and gearbox wear
When switching off the ignition, let the
engine run for a few seconds to allow
the turbocharger (Diesel engine) to
return
  to   idle.
Do not press the accelerator when
switching
  off   the   ignition.
There is no need to engage a gear
after
  parking   the   vehicle.
STARTING AND ST OPPING
Running and accessories position.
To
  unlock   the   steering,   turn   the  
steering wheel gently while turning the
key

,   without   forcing.   In   this   position,  
certain

  accessories   can   be   used.
Starting position.
The starter is operated, the engine
turns
  over,   release   the   key.
STOP position:
  steering   lock.
The
  ignition   is   off.  
T
urn   the   steering  
wheel

  until   the   steering   locks.   Remove  
the

  key.
Opening the bonnet
Before doing anything under the
bonnet, deactivate the Stop & Start
system
 
to
 
avoid
 
the
 
risk
 
of
 
injury
 
related to an automatic change to
ST

ART
 

mode.
Driving on flooded roads
Before
 
driving
 
through
 
a
 
flooded
 
road,
 
it is strongly recommended that you
deactivate

 
the
 
Stop
 
&
 
Start
 
system.
For more advice on driving, particularly
on
 
flooded
 
roads,
 
refer
 
to
 
the
 
corresponding

 
section.
READY TO GO
3
Stop & Start

123
Berlingo2VP_en_Chap05_Securite_ed02-2016
Driving safely
Operation
When your vehicle is too close to or
approaches the vehicle ahead too
quickly  the   system   automatically  
applies

  the   brakes   to   avoid   a   collision.
You are then alerted by the display of a
message.
The
  brake   lamps   on   your   vehicle   come  
on

  to   warn   other   road   users.
The collision can be avoided
automatically if the difference in
speed
between your vehicle and the
vehicle ahead does not exceed 9 mph
(15
  km/h).
Above this threshold, the system will
do what is possible to avoid or reduce
the accident by lowering the speed of
impact.
The
  automatic   braking   may   bring  
the vehicle to a complete stop if the
situation

  requires   it.
In this case, the vehicle is held
stationary temporarily (for about
1.5 seconds)
  to   allow   the   driver   to   take  
back

  control   by   pressing   the   brake  
pedal. The triggering of the system may
cause the engine to stall, unless
the driver depresses the clutch
pedal

  quickly   enough   during   automatic  
braking.
During

  automatic   braking,   the  
driver can always obtain a higher
rate of deceleration than that
controlled by the system, by pressing
firmly

  on   the   brake   pedal.
After an impact, the system is
automatically
  put   out   of   service:   it  
no

  longer   operates.
You must go to a CITROËN dealer or a
qualified
  workshop   to   have   the   system  
made

  operational   again.
Operating limits
The system only detects vehicles that
are stationary or moving in the same
direction  as   your   vehicle.
It does not detect small vehicles
(bicycles, motorcycles),
pedestrians or animals, nor non-
reflective
  stationary   objects.
The system is not triggered or is
interrupted
  if   the   driver:
-

accelerates strongly
-


or turns the steering wheel
suddenly

  (avoiding   manoeuvre).
In
  difficult   weather   conditions   (very  
heavy

  rain,   snow,   fog,   hail...),  
braking

  distances   increase,   which  
can reduce the ability of the system to
avoid

  a   collision.
The driver must therefore remain
particularly
  vigilant.
Never leave accumulations of
snow
  or   any   object   projecting  
above the bonnet or in front of
the

  roof:   this   might   fall   into   the   field   of  
vision of the sensor and generate a
detection.
SAFETY
5

154
Berlingo2VP_en_Chap07_Verification_ed02-2016
OPENING THE BONNET
Bonnet stay
Secure the stay in its location,
identified  by   a   sticker   on   the   right-hand  
side of the vehicle, to hold the bonnet
open.
Before closing the bonnet, put the stay
back

  in   its   clip   without   using   excessive  
force.
On the outside
Raise the bonnet slightly by reaching
in  a   flat   hand,   palm   down,   to   make  
access

  to   the   lever   easier.
With this hand, push the safety catch
to
  the   left.   Raise   the   bonnet.
On the inside
Pull the lever below the dashboard
towards  you.  The   bonnet   is   released.
To close
Lower the bonnet and release it at the
end  of   its   travel.   Check   that   the   bonnet  
is

  secure.
Avoid opening the bonnet in strong
winds.
Opening the bonnet

155
Berlingo2VP_en_Chap07_Verification_ed02-2016Berlingo2VP_en_Chap07_Verification_ed02-2016
PETROL ENGINE
1. Screenwash   fluid   reservoir.
2.  
Fusebox.
3.

 
Engine
  coolant   header   tank.
Battery
  connections:
+
 
Positive
  terminal.
-
 
Negative
  point   (earth).
Take
  care   when   working   under   the   bonnet.
4.  Brake   and   clutch   fluid   reservoir.
5.  
Air
  filter.
6.
 
Engine
  oil   dipstick.7.
 Engine   oil   filler   cap.
8.  
Power
  steering   fluid   reservoir.
CHECKS
7
Under the bonnet

156
Berlingo2VP_en_Chap07_Verification_ed02-2016Berlingo2VP_en_Chap07_Verification_ed02-2016
DIESEL ENGINE
4. Brake   and   clutch   fluid   reservoir.
5.  
Air
  filter.
6.
 
Engine
  oil   dipstick.
7.
 
Engine
  oil   filler   cap. 8.
 Power   steering   fluid   reservoir.
9.
Priming pump
 (except

  BlueHDi   engines).
1.
 Screenwash
 
fluid
 
reservoir.
2.
 
Fusebox.
3.

 
Engine

 
coolant
 
header
 
tank.
Battery
  connections:
+
 
Positive
  terminal.
-
 
Negative
  point   (earth).
Take
 
care
 
when
 
working
 
under
 
the
 
bonnet.
Under the bonnet

 157
Berlingo2VP_en_Chap07_Verification_ed02-2016Berlingo2VP_en_Chap07_Verification_ed02-2016
LEVELS
Oil change
This must be carried out at
the  intervals   specified   in   the  
manufacturer's

  servicing   schedule.  
Ask
 
for

  advice   from   a   CITROËN   dealer.
Remove
  the   dipstick   before   filling.
Check
  the   level   after   filling   (never  
exceed

  the   max   mark).
Refit
  the   oil   filler   cap   before   closing   the  
bonnet.
Changing the brake fluid
The brake fluid must be changed at the intervals stated, according to the
manufacturer's  servicing   schedule.
Use
  fluids   recommended   by   the  
manufacturer

, which meet the DOT4
standard.
The level must be between the MIN
and
  MAX   marks   on   the   reservoir.
If
  fluid   has   to   be   added   frequently,  
this indicates a fault which must be
checked

  by   a   CITROËN   dealer   or  
a

  qualified   workshop   as   soon   as  
possible.
Warning lamps
 If you have to remove / refit the engine style cover, handle it with
care
  to   avoid   damaging   the   fixing  
clips.
Oil level
It is recommended that the oil level be
checked  every   3   000   miles   (5   000   km)  
and topped up if necessary between oil
changes.
Check

  the   level   with   the   vehicle   level,  
engine

  cold,   using   the   dipstick.
Dipstick
Viscosity selection
In all cases, the oil selected must
meet
  the   requirements   specified   in   the  
manufacturer's

  service   schedule.
These regular maintenance
operations
  will   keep   your   vehicle  
in

  good   working   order.  
Ask
  for  
advice from a CITROËN dealer or refer
to the maintenance and warranty guide
in

  the   handbook   pack.
Checks   using   the   warning  
lamps in the instrument panel
is described in chapter 3,
"Instruments and controls"
section.
There

  are   two   marks   on  
the

  dipstick:
A = maximum
If
  you   fill   past   this   mark,  
contact a CITROËN
dealer

  or   a   qualified  
workshop.
B

= minimum
Never allow the level to
fall
  below   this   mark.
To maintain the reliability
of engines and emission
control systems, the use
of additives in engine oil
is
  prohibited.
CHECKS
7
Levels