2017 Citroen BERLINGO ECU

88
Berlingo2VP_en_Chap04_Ergonomie_ed02-2016Berlingo2VP_en_Chap04_Ergonomie_ed02-2016
Row 3 seat adjustments
Placing the seat backrest in the
table position
- 
Lower
  the   head   restraint   fully.
-

Operate the control to fold the seat
backrest

  onto   the   seat   cushion.
Returning the seat backrest to the
sitting position
-
 
Release
  the   seat   backrest   by  
pullin

g the control, then return it to
its
  original   position.
-
 
Check
  that   it   has   correctly   locked   in  
place. Returning the seat to its original
position
-

 
Push
  the   red   control.
-
 
Unfold
  the   entire   seat.
Placing the seat in the fully folded
position
-
 
Place
  the   seat   in   the   table   position.
-
 
Raise
  the   bar   fitted   with   a   red  
strap, located behind the seat, to
release feet of the seat from their
anchorage

  on   the   floor.
-
 
T
ilt   the   entire   seat   forwards.Ensure
  that:
-
 
the
  seat   is   locked   securely   on  
the

  floor,
-

the seat belt is available for
the

  passenger.
Seats

91
Berlingo2VP_en_Chap04_Ergonomie_ed02-2016Berlingo2VP_en_Chap04_Ergonomie_ed02-2016
Operating the Row 3 seats
Removing the seat
- 
Lower
  the   head   restraint.
-

Place the seat in the fully folded
position.
-

 
T
ilt   the   entire   seat   forwards.
-
 
On
  each   side,   take   hold   of   the  
uprights of the folded seat, tilting it
forward

  slightly,   and   lift   it.Refitting the seat
The label on the seat indicates the
position
  in   which   it   must   be   installed.
-
 
Place
  the   hooks   of   the   front   feet  
between

  the   two   bars.
-
 
Ensure
  that   no   object   or   foot   is  
obstructing the rear anchorage
points and that the seat belt is
positioned correctly and available
for

  use.
-
 
Fold
  back   the   seat   to   fix   its   rear  
anchoring

  feet.
-

Operate the control to raise the
seat

  back   to   its   initial   position.
-
 
Raise
  the   head   restraint.
Good practice
Following the various operations:
-
do not remove a head restraint
without stowing it; secure it inside
the vehicle,
-


ensure that the passengers can
always access the seat belts and
fasten them easily

,
-
 
passengers
  must   never   take  
their

  seat   without   adjusting   and  
fastening

  their   seat   belt.
-

a passenger seated in row 3 must
ensure that he does not obstruct
the row 2 seat anchorage points,
-


a passenger seated in row 3 must
not have the seat in front of them in
row 2 in the folded position; this is
in case the seat could tip towards
the passenger unexpectedly and
injure

  them.
Do
  not   place   hard   or   heavy   objects   on  
the

  seat   backs   forming   a   table,   they  
could

  become   dangerous   projectiles   in  
the

  event   or   sharp   braking   or   impact.
EASE OF USE and COMFORT
4
Seats

95
Berlingo2VP_en_Chap04_Ergonomie_ed02-2016Berlingo2VP_en_Chap04_Ergonomie_ed02-2016
Overhead storage unit
This is located above the sun visors
and  can   accommodate   various   objects  
(a

  jumper,   file,   gloves...).
The openings concealed by the sun
visors allow you to see and access the
objects
  stored   in   the   overhead   storage  
unit.
The maximum weight permitted in the
overhead

  storage   unit   is   5   Kg.
Do
  not   place   objects   in   this   storage  
unit

  which   could   present   a   risk   to   the  
occupants.
Central storage console
This console offers an appreciable
additional  storage   area:   it   can   be  
removed and clips onto a base which
also incorporates two cup holders at
the

  rear.
Ensure
  that   the   object   (bottle,   can...)  
placed in the cup holder is retained
securely

  and   does   not   risk   being  
dislodged

  while   driving.
Any liquid which could spill presents
a
  risk   of   damage   on   contact   with   the  
instrument panel and centre console
controls.
T

ake   care.
Sun visor
To prevent dazzle from ahead, fold the
sun  visor   down.
A
 

pocket   is   provided   in   the   driver's   sun  
visor

  for   storing   toll   cards,   tickets,   ...
Storage compartment under
seats
Storage compartments are available,
with  or   without   lid,   in   the   floor   under   the  
front

  seats.
To gain access to them, move the seat
forward.
 
The
  lid   must   be   lifted   from   the  
rear

  of   the   seat.
EASE OF USE and COMFORT
4
Practical information

96
Berlingo2VP_en_Chap04_Ergonomie_ed02-2016Berlingo2VP_en_Chap04_Ergonomie_ed02-2016
SEATING AREA FITTINGS
Floor boxes
Two boxes are available, located under
the  rear   passenger   footwells.
To
  open   them,   slide   your   fingers   into  
the

  recess   and   lift   the   lid.
Aircraft style tables
To put the table in place, pull it
upwards  and   fold   it   down.
As a safety precaution, above a high
pressure, the table is designed to
unhook.
To
  put   it   back   in   place,   with   the   table  
vertical, engage one side then the
other

,   forcing   slightly.
Do
  not   place   hard   or   heavy   objects  
on

  the   table.  
They
  could   become  
dangerous

  projectiles   in   the   event   of  
sharp

  braking   or   impact.
A
 

bag   hook   is   provided   on   the   side   of  
each

  table.
Side blinds
Side blinds may be available on the
sliding   side   doors.
Pull the side blind by the tab to install it.
To avoid damaging the blind when
opening  the   door,   check   that   the   tab   is  
hooked

  securely.
Always guide the blind slowly
using the tab, both when raising
and
  when   lowering.
Practical information

101
Berlingo2VP_en_Chap04_Ergonomie_ed02-2016Berlingo2VP_en_Chap04_Ergonomie_ed02-2016
MODUTOP ROOF BARS
The maximum authorised weight on
each
  roof   bar   is   35   kg. In all cases, the load must rest on
the non-slip bands provided for this
purpose and must not touch the roof or
the
  glazing   of   the   roof.
Recommendations for loading the
roof
This procedure requires the use of
a spanner supplied with the tools for
changing
  a   wheel.
These two longitudinal Modutop roof
bars   can   be   removed.
Chapter 9, "Changing a wheel"
section.
-
 
Open
  the   protective   covers.
-
 
Slacken
  the   four   screws   using   the  
spanner

  and   remove   them.
-

T
urn the bars 90° placing the
hollow
  parts   towards   the   front.
-
 
Refit
  the   the   4   screws   and   tighten  
them

  using   the   spanner.
-
 
Close
  the   protective   covers.
-

Use the strap passages
A only to
secure
  the   load   firmly.
EASE OF USE and COMFORT
4
Practical information

105
Berlingo2VP_en_Chap04_Ergonomie_ed02-2016Berlingo2VP_en_Chap04_Ergonomie_ed02-2016
12 volt socket (120 W max)
It is advisable to limit the use of this
socket  to   avoid   discharging   the   battery.
Protective net
Open the cover located in the hook support.
Fix the top of the net in the notches,
having
  first   turned   the   bar   1/4   of   a   turn.
Ensure that the end of the bar engages
correctly in the metal part of its
location.
Fix the straps in the locations provided
on
  the   floor.
Tighten
  the   net   using   the   straps.
Stowing rings
Use these rings to secure loads on the
floor.
The connection of an electrical
device not approved by CITROËN,
such as a USB charger, may
adversely affect the operation of
vehicle electrical systems, causing
faults such as poor telephone reception
or interference with displays in the
screens.
EASE OF USE and COMFORT
4
Practical information

106
Berlingo2VP_en_Chap04_Ergonomie_ed02-2016Berlingo2VP_en_Chap04_Ergonomie_ed02-2016
REAR FITTINGS
(7 SEAT VERSION )
Cup holder
Any liquid carried in a cup (mug or
other) on board which could spill,
presents   a   risk.
Take
  care.
12 volt socket (120 W max)
It is advisable to limit the use of this
socket   to   avoid   discharging   the   battery.
Stowing rings
Use the stowing rings on the floor to secure  and   retain   your   loads   firmly.
The seat belt anchorages must not be
used
  for   this   purpose.
It is recommended that the load is
immobilised

  by   securing   it   firmly  
using the stowing rings on the
floor

.
Practical information

11 2
Berlingo2VP_en_Chap04_Ergonomie_ed02-2016Berlingo2VP_en_Chap04_Ergonomie_ed02-2016
ELECTRIC WINDOWS
Lower the window fully, then raise it, it
will rise in steps of a few centimetres
each  time   the   control   is   pressed.  
Repeat the operation until the window
is

  fully   closed.
Continue to press the control for at
least one second after the window
closed
  position   has   been   reached.
The safety anti-pinch does not operate
during
  these   operations.
Safety anti-pinch
When the window rises and meets an
obstacle,  it   stops   and   partially   lowers.
Manual mode
This mode is available
depending on equipment; it is
identified
  by   this   symbol   on   the  
control

  in   question.
Good practice
If the electric windows meet an
obstacle during operation, you must
reverse  the   movement   of   the   window.  
T

o  
do
 
this,
 
press
 
the
 
control
 
concerned.
When the driver operates the
passenger electric window controls,
they must ensure that no one is
preventing correct closing of the
windows.
The driver must ensure that the
passengers use the electric windows
correctly

.
Be aware of children when operating
the
  windows.
Following
  several   consecutive   closing/
opening operations of the electric
window control, a protection system
is triggered which only allows closing
of
  the   window.  
After
  closing,   wait  
approximately

  40   minutes.   Once   this  
time has elapsed, the control becomes
operational

  again.
1.
Driver's side
2.

Passenger's side
Reinitialisation
Following reconnection of the battery,
or in the event of a malfunction, the
safety anti-pinch function must be
reinitialised. The electrical functions of the electric
windows   are   deactivated:
-
approximately 45 seconds after the
ignition is switched of

f,
-
after one of the front doors is
opened,

  if   the   ignition   is   off.
There
 
are
 
two
 
operating
 
modes:
Press or pull the control, without
passing
 
the
 
point
 
of
 
resistance.
The window stops when you release
the
 
control.
One-touch mode
Press or pull the control, beyond the
point
  of   resistance.
The window opens or closes fully when
the
  control   is   released.
Pressing or pulling the control again
stops
  the   movement   of   the   window.
Mirrors and windows