2017 Citroen BERLINGO MULTISPACE RHD door lock

23
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Operation in the event
of a battery failure
Front and side passenger doors
In the event of a battery or of the
central  locking   fault,   use   the   lock   to  
lock

  the   doors   mechanically.
-

T
o open the door and get out of the
vehicle,
  pull   the   interior   control.
-
 
T
o   lock   the   door,   insert   the   key   in  
the

  lock,   located   on   the   edge   of   the  
door

, then turn it one eighth of a
turn.
Driver's door
-
 
Insert
  the   key   in   the   lock,   then   turn  
it

  to   the   right   to   lock   or   to   the   left   to  
unlock.
TAILGATE
From inside
(emergency control)
In  the   event   of   a   central   unlocking  
operating

  fault,   this   permits   unlocking  
of

  the   tailgate   from   the   inside.
Insert a small screwdriver in the
opening, between the tailgate and the
floor.
 
T
o   unlock   the   lock,   move   the  
catch

  to   the   left   then   push   the   tailgate.
Opening
From outside
Locking/unlocking  is   by   means   of   the  
remote

  control.
To open, press the control below the
trim
  then   raise   the   tailgate.
A pull strap is available to close the
tailgate
  from   the   high   position.
Guide the closing of the tailgate to the
balance point of its travel then push on
the
  tailgate   to   close   it   fully.
Access
READY TO GO
3

24
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
HINGED REAR DOORS
From outside
To open, pull the handle towards you.Pull the lever to open the right-hand
door
.
To close, start with the right-hand door
then   close   the   left-hand   door.
With   the   roof   rear   flap,   the   rear   bumper  
has been reinforced to serve as a
footrest

  when   entering   the   vehicle.
The hinged rear doors are
asymmetrical   (2/3   -   1/3),   with   the  
smaller

  door   on   the   right.
They   are   fitted   with   a   central   lock.
Tailgate screen
The opening rear screen allows you to
access the rear of the vehicle directly,
without
  having   to   open   the   tailgate.
Opening
After
  unlocking   the   vehicle   using   the  
remote

  control   or   the   key,   press   the  
control and raise the rear screen to
open

  it.
Closing
Close the rear screen by pressing
the centre of the glass until it is fully
closed.
The tailgate and tailgate screen
cannot both be open at the
same time, to prevent damage to
the screen.
Access

25
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
In practice
It is possible to drive with the right-
hand  door   open   to   make   it   easier   to  
carry

  long   loads.  
The
  left-hand   door   is  
kept

  closed   by   the   distinctive   "yellow"  
lock,

  positioned   at   the   base   of   the   door.  
This closed door must not be used as
a

  load   retainer.
Driving with the right-hand door open
is
  a   special   dispensation.   Comply   with  
the usual safety indications to warn
other

  drivers.
From inside
When present on the vehicle, pulling
this handle towards you opens the left-
hand  door.
Opening to approximately 180°
A check   strap   system   permits   extension  of the opening from approximately 90°
to
  approximately   180°.
Pull the yellow control when the door is
open.
The
  check   strap   will   engage   again  
automatically

  on   closing.
When parked with the rear doors open to 90°,
the  doors   mask   the   rear  
lamps.

 
T
o   signal   your  
position to other road
users driving in the same
direction who may not
have seen your vehicle,
use a warning triangle
or other device required
by the legislation in your
country

.
Access
READY TO GO
3

26
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
REAR ROOF FLAP
Support bar
A support bar is provided for
transporting long loads, after opening
the  rear   roof   flap.
Fold
  back   the   support   bar   by   lifting   the  
lever

.
Guide
  it   to   the   door   pillar.
Support the long loads to be
transported, lift them and reposition the
support
  bar   with   one   hand.
Ensure that it is secured correctly by
pressing the handle downwards past
the point of resistance and secure the
loads
  firmly. The rear bumper has been
reinforced to serve as a footrest
when
  entering   the   vehicle.
The   rear   doors   only   lock   when   the  
support

  bar   is   installed.
When
  the   rear   roof   flap   is   open,   take  
care when driving where height is
restricted.
Never rest loads directly on the rear
doors.
Comply with the usual indications, to
warn

  other   drivers.
Reserve
  the   use   of   the   rear   roof   flap  
for

  short   journeys.
The side supports can be used as
hooking
  points.
-  
lower
  the   black   paddle   to   secure  
the

  rear   roof   flap.
Securing   the   rear   roof   flap   places   it   on  
the seal correctly and ensures sealing
without

  noise.
This
 
rear
 
roof
 
flap
 
is
 
only
 
compatible
 
with

 
side-hinged
 
rear
 
doors.
To
 
open
 
the
 
rear
 
roof
 
flap:
-
 
raise

 
the
 
black
 
paddle
 
of
 
the
 
toggle,
-

relieve the toggle by pressing the
rear

 
roof
 
flap
 
(downwards)
 
then
 release
 
the
 
hook,
-
 lift
 
the
 
rear
 
roof
 
flap,
-

pass the point of resistance to
secure

 
the
 
rear
 
roof
 
flap
 
using
 
the
 
support

 
stays.
Never
 
drive
 
without
 
the
 
stays
 
in
 
place.
To
 
close
 
the
 
rear
 
roof
 
flap:
-
 
check

 
that
 
the
 
support
 
bar
 
is
 
secured correctly

,
-
 
lower

 
the
 
rear
 
roof
 
flap,
-
 
while

 
pressing
 
the
 
rear
 
roof
 
flap
 
(downwards),

 
take
 
hold
 
of
 
the
 
two


loops of the spring then place
the
 
hook
 
in
 
its
 
housing, Never attach any load to the rear roof
flap.
Never drive without the support bar in
place.
Access

27
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
CENTRAL LOCKING
An initial press permits
central
  locking   of   the   vehicle,  
when all of the doors are
closed.
Door open warning lamp
The

  control   switch   LED:
-  
flashes
  when   the   doors   are   locked  
with the vehicle stationary and the
engine of

f,
-

comes on when the doors are
locked

  and   from   the   time   the  
ignition

  is   switched   on.
Anti-intrusion security
If this warning lamp comes
on,  check   that   all   of   your  
vehicle's doors are closed
correctly

.
Locking while driving
When the vehicle moves off, as soon
as you reach approximately 6 mph
(10 km/h),
  the   system   locks   the   doors.
 The

  characteristic   central   locking   noise
 is

  heard.  
The
  LED   in   the   switch   on   the
 dashboard

  central   switch   panel   comes   on.
During the journey, opening a door results  in   complete   unlocking   of   the  
vehicle.
Activating / deactivating the
function
With the ignition on, press
and hold this switch to
activate or deactivate the
function.
Driving

 
with
 
the
 
doors
 
locked
 
may
 
make

 
access
 
to
 
the
 
interior
 
more
 
difficult

 
in
 
an
 
emergency.
A second press permits central
unlocking
 
of
 
the
 
vehicle.
The control is inactive when the vehicle
has
 
been
 
locked
 
using
 
the
 
remote
 
control

 
or
 
the
 
key
 
from
 
the
 
outside.
The doors can still be opened from the
inside.
Access
READY TO GO
3

+
ABS
35
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Instruments and controls
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Warning lamp isindicatesSolution - action
Power
steering on. a fault with the
system.
The vehicle
 retains  conventional  steering  without  assistance. Have
  it   checked   by   a   CITROËN   dealer   or   a   qualified workshop.
Door open
detectionon and accompanied
by a message in the
screen. that a door is not
closed
  correctly.Check
  that   all   of   the   doors   are   closed.
ABS remaining
  on.a fault with the anti-
lock
  braking   system.The
  vehicle   retains   conventional   braking.
Have
  it   checked   by   a   CITROËN   dealer   or   a  
qualified

  workshop.
ESC flashing.
triggering of the ASR
or
  DSC   regulation.The system optimises traction and improves the
directional
  stability   of   the   vehicle.
Chapter
  5,   "Driving   safety"   section.
remaining
  on.a fault with the
system.
E.g.:
  under-inflation  
of

  the   tyres.E.g.:
  check   the   pressure   of   the   tyres.
Have
  it   checked   by   a   CITROËN   dealer   or   a  
qualified

  workshop.   (Wheel   speed   sensor,  
hydraulic

  valve   block,   ...).
Under-
inflation on.
the tyre pressure is
too low in or more
wheels.Check
  the   tyre   pressure   as   soon   as   possible.
This
  check   must   be   done   with   the   tyres   cold.
flashing
  then
 remaining on,


accompanied by the
Service warning
lamp, and depending
on equipment, the
display
  of   a   message.the tyre pressure
monitoring system
has a fault or one of
the wheels does not
have
  a   sensor.Detection
  of   under-inflation   is   no   longer   assured.
Have
  it   checked   by   a   CITROËN   dealer   or   a  
qualified

  workshop.
Particle filter on. a problem with the
particle
  filter   (fuel  
additive

  level,   risk   of  
blockage, ...).Have

  the   filter   checked   by   a   CITROËN   dealer   or  
a

  qualified   workshop.
Chapter
  7,   "Levels"   section.
READY TO GO
3

55
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
The Stop & Start system
requires  a   battery   of   specific  
characteristics.

 
All
  work   on   this  
type of battery must be done only
by

 
a
  CITROËN   dealer   or   a   qualified  
workshop.
For more information on the 12 V
battery

,   refer   to   "Battery"   in   section   8.
Good practice when stopping Good practice when starting
Diesel pre-heating warning
lamp
If the temperature is high
enough, the warning lamp
comes on for less than
one second, you can start
without
  waiting.
In cold weather, wait for this warning
lamp to go off then operate the starter
(Starting position) until the engine
starts. Door or bonnet open
warning lamp
If this comes on, a door or the bonnet
is
  not   closed   correctly,   check!
Minimise engine and gearbox wear
When switching off the ignition, let the
engine run for a few seconds to allow
the turbocharger (Diesel engine) to
return
  to   idle.
Do not press the accelerator when
switching
  off   the   ignition.
There is no need to engage a gear
after
  parking   the   vehicle.
STARTING AND ST OPPING
Running and accessories position.
To
  unlock   the   steering,   turn   the  
steering wheel gently while turning the
key

,   without   forcing.   In   this   position,  
certain

  accessories   can   be   used.
Starting position.
The starter is operated, the engine
turns
  over,   release   the   key.
STOP position:
  steering   lock.
The
  ignition   is   off.  
T
urn   the   steering  
wheel

  until   the   steering   locks.   Remove  
the

  key.
Opening the bonnet
Before doing anything under the
bonnet, deactivate the Stop & Start
system
 
to
 
avoid
 
the
 
risk
 
of
 
injury
 
related to an automatic change to
ST

ART
 

mode.
Driving on flooded roads
Before
 
driving
 
through
 
a
 
flooded
 
road,
 
it is strongly recommended that you
deactivate

 
the
 
Stop
 
&
 
Start
 
system.
For more advice on driving, particularly
on
 
flooded
 
roads,
 
refer
 
to
 
the
 
corresponding

 
section.
READY TO GO
3
Stop & Start

103
Berlingo2VP_en_Chap04_Ergonomie_ed02-2016Berlingo2VP_en_Chap04_Ergonomie_ed02-2016
Automatic switching on/off
The front courtesy lamp comes on when
the  key   is   removed   from   the   ignition,   when the

  vehicle   is   unlocked,   when   one   of   the
 front doors is opened and for location of


the
  vehicle   using   the   remote   control.
It goes off gradually after the ignition is
switched on and when the vehicle is
locked.Front seats: comes on when one of the front doors is
opened. These are switched on and of
f by
means of a manual switch, with
the
  ignition   on.
Rear
  seats:   comes   on   when  
one of the rear doors is
opened.
If the doors remain open for
a few minutes, the courtesy
lamps

  go   off.
Permanently
  off.
Permanently
 
on,
 
ignition
 
on.
Front courtesy lamp
COURTESY
LAMPS
Rear courtesy lamp Front individual reading lamps
EASE OF USE and COMFORT
4
Practical information