2017 Citroen BERLINGO MULTISPACE RHD bulb

181
Berlingo2VP_en_Chap08_Aide-rapide_ed02-2016Berlingo2VP_en_Chap08_Aide-rapide_ed02-2016
CHANGING A BULB
Type A
All  glass   bulb:   pull   gently  
as

  it   is   fitted   by   pressure.
Type C
Halogen
  bulb:   release   the  
retaining spring from its
housing. T
ype B
Bayonet
  bulb:   press  
on the bulb then turn it
anticlockwise.
T

ypes of bulb
Various
 
types
  of   bulb   are   fitted   to   your  
vehicle.
T

o
 
remove
 
them:
Type D
Light-emitting diode
(LED):
  for   replacement  
of the daytime running
lamps, contact a
CITROËN dealer or a
qualified

  workshop.
QUICK HELP
8
Changing a bulb

182
Berlingo2VP_en_Chap08_Aide-rapide_ed02-2016Berlingo2VP_en_Chap08_Aide-rapide_ed02-2016
2. Sidelamps
Type A, W5W - 5W
-
Remove the cover by pullin
g the
flexible
  rubber   tab.
-
 
Remove
  the   bulb   holder   fitted   by  
pressure

  by   pulling   the   connector.
-
 
Change
  the   bulb.
-
 
Ensure
  that   the   cover   is   refitted  
correctly all round to assure correct
sealing.
Front lamps
1. Dipped / Main beam headlamps
T ype C, H4 - 55W
-

Remove the centre cover by pullin
g
the
  flexible   rubber   tab.
-
 
Disconnect
  the   electrical   connector.
-
 
Release
  the   retaining   tab.
-
 
Change
  the   bulb   taking   care  
to align the metal part with the
grooves

  on   the   lamp.
-
 
Reposition
  the   retaining   tab.
-
 
Ensure
  that   the   cover   is   refitted  
correctly all round to assure correct
sealing.
High pressure washing Open

 
the
 
bonnet.
 
T

o
 
access
 
the
 
bulbs,
 
reach

 
behind
 
the
 
headlamp
 
unit.
Carry out the operations in reverse
order
 
to
 
refit
 
each
 
bulb
 
and
 
check
 
that
 
the

 
bonnet
 
is
 
closed
 
securely.
Halogen bulbs must be changed
with
 
the
 
headlamp
 
off.
 
Wait
 
a
 
few
 
minutes

 
(risk
 
of
 
serious
 
burns).
 
Do not touch the bulb directly with your
fingers,

 
use
 
lint-free
 
cloths.
It is normal for condensation to form
inside
 
the
 
headlamps.
 
Regular
 
use
 
of
 the
 
vehicle
 
eliminates
 
this
 
misting.
The bulbs must be changed with
the ignition off or with the battery
disconnected.
 
Wait
 
approximately
 
3


minutes after changing the bulb
before
 
reconnecting
 
the
 
battery.
Check
 
that
 
the
 
lamps
 
operate
 
correctly
 
after

 
each
 
operation.
When using this type of washing
on stubborn dirt, do not persist on
the headlamps, the lamps and their
edges to avoid damaging their coating
and
 
seals.
Changing a bulb

183
Berlingo2VP_en_Chap08_Aide-rapide_ed02-2016Berlingo2VP_en_Chap08_Aide-rapide_ed02-2016
3. Direction indicators
Type B, PY21W - 21W (amber)
-
Remove the cover by pullin
g the
flexible
  rubber   tab.
-

T
urn the bulb holder a quarter turn
anticlockwise.
-

Remove the bulb by pressing it
lightly

  while   turning   it   anticlockwise.
-
 
Change
  the   bulb.
-
 
Ensure
  that   the   cover   is   refitted  
correctly all round to assure correct
sealing. 4. Front foglamps
T

ype C, H1 - 55W
-

Remove the three clips and the
screw securing the wheel arch liner

,
located
  below   the   bumper.
-
 
Move
  the   wheel   arch   liner   upwards.
-

Disconnect the bulb holder
connector by pressing the tab at
the

  top.-

Remove the bulb holder by
squeezing the two clips (at top and
bottom)

  using   a   finger   and   thumb.
-

Replace the module (bulb holder
and

  bulb).
-

Carry out the operations in reverse
order

  to   fit   the   module   and   refit   the  
wheel

  arch   liner.
QUICK HELP
8
Changing a bulb

184
Berlingo2VP_en_Chap08_Aide-rapide_ed02-2016Berlingo2VP_en_Chap08_Aide-rapide_ed02-2016
Side repeater
Type A, WY5W - 5W (amber)
-
Push the repeater towards the rear
and disengage it by pullin

g the
front.
-

Contact a CITROËN dealer to
obtain a new repeater which is a
sealed

  component.
-
 
T
o   refit,   engage   the   repeater  
towards the rear and bring it
towards

  the   front.
Courtesy lamps
Type A, 12V5W - 5W
-
Unclip the lens by sliding a
screwdriver in the slots on each
side

  of   the   courtesy   lamp.
-
 
Pull
  the   bulb   out   and   change   it.
-

Clip the lens in its housing and
ensure

  that   it   is   secured   correctly.
Front / Rear
Changing a bulb

185
Berlingo2VP_en_Chap08_Aide-rapide_ed02-2016Berlingo2VP_en_Chap08_Aide-rapide_ed02-2016
Rear lamps
This procedure requires the use of
the spanner supplied with the tools for
changing  a   wheel.
When
  refitting,   take   care   to  
reposition the tabs and the wiring
correctly to avoid trapping the
wiring.
After changing the rear direction
indicator bulb, the reinitialisation time is
above

  2   minutes.
-
Move aside the 4 tabs then extract
the
  bulb   holder.
-

Remove the faulty bulb by
pressing it lightly while turning it
anticlockwise.
-

 
Change
  the   bulb.
When
  removing   the   lamp   unit:
-

with tailgate, pull the lamp unit
towards the centre of the vehicle,
-


with hinged doors, pull the lamp
unit

  towards   you.
For more information on bulbs, refer to
the
 
"Types
 
of
 
bulb".
1.

Brake lamps / sidelamps


T

ype B,
 
P21/5W
 
-
 
21/5W
2.

Direction indicators


T

ype B, PY21W - 21W (amber)
3.

Reversing lamps


T

ype B, P21W - 21W
4.

Foglamps


T

ype B, P21W - 21W
High pressure jet washing When using this type of washing
on stubborn dirt, do not persist on
the headlamps, the other lamps
and their edges to avoid damaging
their
 
coating
 
and
 
seals. Chapter 9, "Changing a wheel"
section.
-

Identify the failed bulb, then open
the

  rear   doors   to   180°.
Chapter
  3,   "Access"   section.
-
 
Remove
  the   two   fixing   bolts   using  
the

  spanner   provided.
-
 
Pull
  the   lamp   unit   from   the   outside.
-

Holding the lamp, disconnect the
electrical

  connector.
QUICK HELP
8
Changing a bulb

186
Berlingo2VP_en_Chap08_Aide-rapide_ed02-2016Berlingo2VP_en_Chap08_Aide-rapide_ed02-2016
Number plate lamps
- Unscrew  the   two   nuts.
-  
Push
  the   pins.
-

If necessary
, disconnect the
connector
  to   remove   the   lamp.
-
 
Change
  the   bulb.
Third brake lamp
Type A, W16W - 16W
Type A, W5W - 5W
With tailgate
-

Disengage the plastic lens using a
screwdriver

.
-
 
Change

 
the
 
bulb.
-

Replace the plastic lens and press
on

 
it. With hinged doors
-
 
Unclip

 
the
 
interior
 
trim.
-

Disconnect the connector by
moving

 
aside
 
its
 
tab.
-

T

urn the bulb holder a quarter turn
anticlockwise.
-
 
Change

 
the
 
bulb.
-
 
Put

 
the
 
bulb
 
holder
 
back
 
in
 
place
 
and

 
reconnect
 
the
 
connector.
-
 
Put

 
the
 
trim
 
back
 
in
 
place.
Changing a bulb