2017 CHRYSLER PACIFICA HYBRID towing

TRI-PANE PANORAMIC SUNROOF — IF
EQUIPPED ............................ .123
▫ Opening Sunroof ...................... .124
▫ Closing Sunroof ....................... .125
▫ Wind Buffeting ....................... .125
▫ Power Sun Shade — If Equipped ............125
▫ Pinch Protect Feature ....................126
▫ Sunroof Maintenance ....................126
▫ Ignition Off Operation ...................126
 HOOD .............................. .126
▫ Opening ............................ .126
▫ Closing ............................. .128
 LIFTGATE ............................ .128
▫ Opening ............................ .128
▫ Closing ............................ .129▫
Power Liftgate — If Equipped ..............130
▫ Hands-Free Liftgate — If Equipped ..........132
▫ Cargo Area Features .....................134
 INTERNAL EQUIPMENT ..................134
▫ Storage ............................. .134
▫ Illuminated Vanity Mirrors — If Equipped . . . .138
▫ Power Outlets ........................ .138
▫ Power Inverter — If Equipped .............142
▫ Cigar Lighter — If Equipped ...............142
▫ Smoker’s Package Kit — If Equipped ........143
▫ Overhead Storage With Sunglass Storage ......143
 ROOF LUGGAGE RACK — IF EQUIPPED ......144
▫ Deploying

The Crossbars .................145
▫ Stowing The Crossbars ...................147
16 GETTING TO KNOW YOUR VEHICLE

4. Once the crossbar is in place, tighten both thumb screwscompletely.
5. Deploy and tighten the second crossbar to complete the deployment of the crossbars.
NOTE: The crossbars are not identical and have fixed
deployment positions. Rear crossbar can be deployed in
two different positions.Stowing The Crossbars
1. Starting with one crossbar, completely loosen the thumb screws at both ends. Lift the crossbar away from the
matching letter to remove it from the deployed position.
Repeat with the other crossbar.
CAUTION!
Use care when removing and handling the crossbars to
prevent damage to the vehicle.
Installing Crossbars
3
GETTING TO KNOW YOUR VEHICLE 147

2. Starting with the one crossbar, bend up the pivotsupports at each end. 3. Then, position the crossbar along the correct side rail.
Make sure the letters on the crossbar align with the
matching letters on the side rail.
Crossbar Pivot
Stowing Crossbars
148 GETTING TO KNOW YOUR VEHICLE

NOTE:
•The charging system is independent from load reduc-
tion. The charging system performs a diagnostic on the
charging system continuously.
• If the Battery Charge Warning Light is on it may indicate
a problem with the charging system. Refer to “Battery
Charge Warning Light” in ”Warning And Indicator
Lights And Messages” located in ”Getting To Know
Your Instrument Panel” for further information.
The electrical loads that may be switched off (if equipped),
and vehicle functions which can be effected by load reduction:
• Heated Seat/Vented Seats/Heated Wheel
• Heated/Cooled Cup Holders — If Equipped
• Rear Defroster And Heated Mirrors
• HVAC System
• 115V AC Power Inverter System
• Audio and Telematics System
Loss of the battery charge may indicate one or more of the
following conditions:
• The charging system cannot deliver enough electrical
power to the vehicle system because the electrical loads are larger than the capability of charging system. The
charging system is still functioning properly.
• Turning on all possible vehicle electrical loads (e.g.
HVAC to max settings, exterior and interior lights,
overloaded power outlets +12V, 115V AC, USB ports)
during certain driving conditions (city driving, towing,
frequent stopping).
• Installing options like additional lights, upfitter electri-
cal accessories, audio systems, alarms and similar de-
vices.
• Unusual driving cycles (short trips separated by long
parking periods).
• The vehicle was parked for an extended period of time
(weeks, months).
• The battery was recently replaced and was not charged
completely.
• The battery was discharged by an electrical load left on
when the vehicle was parked.
• The battery was used for an extended period with the
vehicle not running to supply radio, lights, chargers,
+12V portable appliances like vacuum cleaner ’s, game
consoles and similar devices.
166 GETTING TO KNOW YOUR INSTRUMENT PANEL

Electric Power Steering Fail Warning Light
Red TelltaleLight What It Means
Electric Power Steering Fail Warning
This light is used to manage the electrical warning of the EPS (Power Steering System). Refer to
“Power Steering” in “Starting And Operating” for further information.
Electronic Throttle Control (ETC) Warning Light
Red Telltale
Light What It Means
Electronic Throttle Control (ETC) Warning Light
This light informs you of a problem with the Electronic Throttle Control (ETC) system. If a prob-
lem is detected while the vehicle is running, the light will either stay on or flash depending on
the nature of the problem. Cycle the ignition when the vehicle is safely and completely stopped
and the transmission is placed in the PARK position. The light should turn off. If the light re-
mains on with the vehicle under power, your vehicle will usually be drivable; however, see an
authorized dealer for service as soon as possible.
If the light continues to flash when the vehicle is under power, immediate service is required and
you may experience reduced performance, and your vehicle may require towing. The light will
come on when the ignition is placed in the ON/RUN position and remain on briefly as a bulb
check. If the light does not come on during starting, have the system checked by an authorized
dealer.
172 GETTING TO KNOW YOUR INSTRUMENT PANEL

Engine Malfunction Warning Light
Yellow TelltaleLight What It Means
Vehicle Check/Malfunction Indicator Light (MIL)
The Vehicle Check/Malfunction Indicator Light (MIL) is a part of an Onboard Diagnostic System
called OBD II that monitors emissions control systems. The light will illuminate when the igni-
tion is in the ON position before vehicle start up. If the bulb does not come on when placing the
ignition in the ON/RUN position, have the condition checked promptly.
Certain conditions, such as a loose or missing gas cap, poor quality fuel, etc., may illuminate the
light after vehicle start. The vehicle should be serviced if the light stays on through several typi-
cal driving styles. In most situations, the vehicle will drive normally and will not require towing.
When the vehicle is running, the MIL may flash to alert serious conditions that could lead to im-
mediate loss of power or severe catalytic converter damage. The vehicle should be serviced as
soon as possible if this occurs.
WARNING!
A malfunctioning catalytic converter, as referenced
above, can reach higher temperatures than in normal
operating conditions. This can cause a fire if you drive
slowly or park over flammable substances such as dry
plants, wood, cardboard, etc. This could result in death
or serious injury to the driver, occupants or others.
CAUTION!
Prolonged driving with the Malfunction Indicator
Light (MIL) on could cause damage to the vehicle
control system. It also could affect fuel economy and
driveability. If the MIL is flashing, severe catalytic
converter damage and power loss will soon occur.
Immediate service is required.
182 GETTING TO KNOW YOUR INSTRUMENT PANEL

your service technician in making repairs. Although your
vehicle will usually be drivable and not need towing, see
your authorized dealer for service as soon as possible.
CAUTION!
•Prolonged driving with the MIL on could cause
further damage to the emission control system. It
could also affect fuel economy and driveability. The
vehicle must be serviced before any emissions tests
can be performed.
• If the MIL is flashing while the vehicle is running,
severe catalytic converter damage and power loss
will soon occur. Immediate service is required.
Onboard Diagnostic System (OBD II) Cybersecurity
Your vehicle is required to have an Onboard Diagnostic
system (OBD II) and a connection port to allow access to
information related to the performance of your emissions
controls. Authorized service technicians may need to ac-
cess this information to assist with the diagnosis and
service of your vehicle and emissions system.
WARNING!
• ONLY an authorized service technician should con-
nect equipment to the OBD II connection port in
order to diagnose or service your vehicle.
• If unauthorized equipment is connected to the OBD
II connection port, such as a driver-behavior tracking
device, it may:
• Be possible that vehicle systems, including safety
related systems, could be impaired or a loss of
vehicle control could occur that may result in an
accident involving serious injury or death.
• Access, or allow others to access, information
stored in your vehicle systems, including personal
information.
For further information, refer to “Privacy Practices” and
“Uconnect CyberSecurity” in “All About Uconnect Access”
in your Owner ’s Manual Radio Supplement and “Cyber-
security” in “Multimedia”.
4
GETTING TO KNOW YOUR INSTRUMENT PANEL 191

▫Parallel Parking Space Assistance
Operation/Display ..................... .346
▫ Perpendicular Parking Space Assistance
Operation/Display ..................... .354
 LANESENSE — IF EQUIPPED ..............363
▫ LaneSense Operation ....................363
▫ Turning LaneSense On Or Off ..............364
▫ LaneSense Warning Message ...............365
▫ Changing LaneSense Status ................368
 PARKVIEW REAR BACK UP CAMERA — IF
EQUIPPED ........................... .368
 SURROUND VIEW CAMERA SYSTEM — IF
EQUIPPED ........................... .370
REFUELING THE VEHICLE ................374
 VEHICLE LOADING .....................377
▫ Certification Label ..................... .377
 TRAILER TOWING ..................... .379
 RECREATIONAL TOWING ................380
▫ Towing This Vehicle Behind Another Vehicle. . . .380
▫ Recreational Towing — All Models ..........380
 DRIVING TIPS ......................... .381
▫ Driving On Slippery Surfaces ..............381
▫ Driving Through Water ..................382
6
STARTING AND OPERATING 281