2017 CHRYSLER PACIFICA HYBRID lights

FRONT VIEW
Front View
1 — Hood/Engine Compartment
2 — Headlights
3 — Wheels/Tires
4 — Windshield5 — Charging Port Door
6 — Exterior Mirrors
7 — Doors
8 — Fuel Door
8 GRAPHICAL TABLE OF CONTENTS

REAR VIEW
Rear View
1 — Rear Lights
2 — Rear Windshield Wiper
3 — Liftgate
2
GRAPHICAL TABLE OF CONTENTS 9

▫Illuminated Vanity Mirrors — If Equipped .....93
▫ Conversation Mirror .....................93
 EXTERIOR LIGHTS .......................94
▫ Headlight Switch .......................94
▫ Automatic Headlights — If Equipped .........94
▫ Headlights On With Wipers — If Equipped .....94
▫ Headlight Delay — If Equipped .............95
▫ Lights-On Reminder .....................95
▫ Daytime Running Lights — If Equipped .......95
▫ Front Fog Lights — If Equipped .............96
▫ Multifunction Lever .....................96
▫ Turn Signals ...........................97
▫ Lane Change Assist — If Equipped ..........97
▫ High/Low Beam Switch ..................97
▫ Flash-To-Pass ..........................97
▫ Automatic High Beam — If Equipped ........97
▫ Battery Protection .......................98 
INTERIOR LIGHTS .......................98
▫ Courtesy/Interior Lighting ................98
▫ Instrument Panel Dimmer Control ..........100
 WINDSHIELD WIPER AND WASHERS ........101
▫ Intermittent Wiper System ................101
▫ Windshield Wiper Operation ...............102
▫ Windshield Washers .....................102
▫ Mist Feature ......................... .102
▫ Rear Wiper And Washer ..................102
▫ Rain Sensing Wipers — If Equipped .........102
 CLIMATE CONTROLS ....................104
▫ Overview ........................... .104
▫ Automatic Temperature Control (ATC) — If
Equipped ............................111
▫ Operating
Tips........................118
 WINDOWS ........................... .120
▫ Power Windows ....................... .120
3
GETTING TO KNOW YOUR VEHICLE 15

WARNING!
Improper connection of the equipment-grounding con-
ductor could result in a risk of electric shock. Check
with a qualified electrician or serviceman if you are in
doubt as to whether the wall receptacle is properly
grounded. Do not modify the plug provided with the
product – if it does not fit the outlet, you must have a
proper outlet installed by a qualified electrician.
2. Check to see if the charging cordset is ready to charge by reviewing the indicator lights. After a brief self-check,
where the indicator light will flash, a green AC indicator
light and two green “charge active” indicator lights
indicate that the cordset is ready for use.
Cordset Indicator Lights
1 — AC Power Indicator Light
2 — Fault Indicator Light3 — Charge Active Indicator
Lights
3
GETTING TO KNOW YOUR VEHICLE 23

3. If the charging cordset is ready to charge, ensure thevehicle is in PARK, and then connect the charge connec-
tor to the vehicle’s charge inlet. You will hear a “click”
when the charge connector is inserted correctly and
coupled with the vehicle’s charge inlet.
4. When the vehicle commences charging, the Charge Active Indicator Lights will cycle from left to right, and
then both turn off. This pattern will repeat while the
vehicle is charging. The lights are illuminated at the rate
of approximately one cycle per second. NOTE:
The vehicle should start charging automatically. If
not, please check the following:
•Charging Cordset - The charging cordset status indi-
cators illuminate green or red to identify the charging
cordset status. Refer to “Troubleshooting Using The
Status Indicator Display” in this section for further
information on the charging cordset status.
• Wall Receptacle – Check whether the wall receptacle is
functional (no power outage) and/or plug the charg-
ing cordset into a different wall receptacle.
• Charging Schedule – Check whether or not the charg-
ing schedules have been enabled. If enabled, check
that you are within the scheduled time and date. If a
charging schedule has been enabled in the vehicle, and
you are outside the time and date, you may override
the schedule for this charging event by plugging in the
charge connector, unplugging it, and then plugging it
back into the vehicle charge inlet. Complete the double
plug sequence within 10 seconds for it to override the
set schedule.
Inserting The Charge Connector Into The Vehicle Charge
Inlet
24 GETTING TO KNOW YOUR VEHICLE

5. To stop the charging process, disconnect the vehicle sideconnector first and then the charging cordset from the
wall receptacle. To disengage the vehicle coupler, press
the button on the charge connector first and then
remove the connector from the vehicle charge inlet.
6. Close the inlet door. NOTE:
It is good practice to keep the ignition in the OFF
position while conducting Level 1 Charging. This mini-
mizes any additional vehicle loads the EVSE has to support
which extend the charging time.
Troubleshooting Using The Status Indicator Display
If the vehicle is not charging properly, consult the status
indicator lights.
The AC Power Indicator displays the status and safety of
the input power. If this indicator is green, the power is
within acceptable limits to charge the vehicle. If only the
AC Power Indicator is flashing red, then there is a problem
with the AC power at the electrical outlet. If the AC Power
Indicator does not return to green, then the outlet should
be inspected by a licensed electrician to ensure the voltage,
frequency, and grounding are complaint to national and
local electrical codes and ordinances. It may be possible to
attempt charging from a different outlet.
Removing The Charge Connector From The Vehicle
Charge Inlet
3
GETTING TO KNOW YOUR VEHICLE 25

Instrument Panel State Of Charge Indicator
In addition to the battery gauge your vehicle is equipped
with a visual state of charge indicator. The state of charge
indicator is made up of five lights that are mounted to the
top center of the instrument panel, which will illuminate
when the vehicle is plugged into the EVSE.The state of charge indicator represents the current state of
charge for the high voltage battery and if there is a fault
with the charging system. The state of charge indicator
illuminates quickly to provide the charging system status
to the vehicle operator . Each light represents the battery’s
current percentage of charge, as shown below in the table.
The charge indicator will illuminate from left to right one
light at a time to indicate that there is a scheduled charge
enabled.
NOTE:
The lights scroll one at a time when the vehicle is
plugged in outside of its charging schedule time/date, and
it is waiting on the schedule to begin charging.
State Of Charge Indicator
3
GETTING TO KNOW YOUR VEHICLE 33

In the event of an error in the charging process the outer
two lights will blink.
Number Of IndicatorLights Illuminated Percent Of Battery Charge
1st light blinks 0 – 20%
1st light ON, second light
blinks 21 – 40%
1st and 2nd lights ON,
3rd light blinks 41 – 60%
1st, 2nd, and 3rd light
ON, 4th light blinks 61 – 80%
1st, 2nd, 3rd, and 4th
light ON, 5th light blinks 81 – 95%
All 5 lights ON 100%
Two outer lights are
blinking Indicates an error in the
charging process.
Hybrid Electric Pages
Within your Uconnect 8.4/8.4 NAV radio is the “Hybrid
Electric” App that allows you to see your vehicle’s power
flow, understand your drive history, and set a charging
schedule for your vehicle’s battery. To access this app, press
the “Apps” button on the main menu bar of the radio’s
touch screen, and locate the “Hybrid Electric” App. Press-
ing the “Hybrid Electric” App will bring you to a set of
three pages, Power Flow, Driving History, and Charging
Schedule, that are all related to your hybrid vehicle’s
battery performance.
Hybrid Electric App Location
34 GETTING TO KNOW YOUR VEHICLE