Chevrolet Low Cab Forward Owner Manual (GMNA-Localizing-U.S.-
10716700) - 2017 - crc - 12/6/16
270 Vehicle Care
is overheating. The engine overheat
warning light will come on and on a
diesel vehicle, the warning buzzer
will sound. Either steam or boiling
engine coolant will squirt out of the
radiator. The diesel vehicle will also
have an“OVER HEAT” message
displayed. Take the following
corrective actions immediately.
{Warning
To help avoid being burned:
Do not tilt the cab or open the
engine access cover if you see or
hear steam or engine coolant
escaping from the engine
compartment. Wait until no steam
or engine coolant can be seen or
heard before tilting the cab or
opening the engine cover.
Do not remove the radiator cap or
engine coolant reserve tank cap if
the engine coolant in the tank is
boiling. Also do not remove the
radiator cap while the engine and
radiator are still hot. Scalding fluid
(Continued)
Warning (Continued)
and steam can be blown out
under pressure if either cap is
taken off too soon.
You and others could be seriously
injured.
If Steam is Coming from the
Engine Compartment
{Warning
If the engine coolant temperature
gauge shows an overheat
condition or you have other
reasons to suspect the engine
may be overheating, continued
operation of the engine (other
than as described here) even for
a short period of time may cause
a fire and the result in personal
injury and severe vehicle
damage. Take immediate action
as outlined.
You and others could be seriously
injured. If you see or hear escaping steam
or have any other reason to suspect
there is a serious overheat
condition, stop and park the vehicle
as soon as it is safe to do so, turn
on the hazard warning flasher and
then turn off the engine immediately
and safely exit the vehicle.
If Steam Is Not Coming from the
Engine Compartment
Chevrolet Low Cab Forward Owner Manual (GMNA-Localizing-U.S.-
10716700) - 2017 - crc - 12/6/16
272 Vehicle Care
4. If no steam or engine coolantcan be seen or heard from the
engine compartment:
.Tilt the cab or open the
engine access cover.
‐If the engine coolant is
boiling, wait until it stops
before proceeding.
‐ Look at the see-through
reserve tank. The
engine coolant level
should be between the
"MAX" and "MIN" lines
on the reserve tank.
‐ If necessary, pour
engine coolant (See
Engine Coolant 0263
for the proper coolant
and water mixture) into
the reserve tank only,
not directly into the
radiator. Also, do not
check engine coolant
level at the radiator.
. Make sure the fan belts are
not broken, or off the
pulleys, and that the fan
turns when the engine is started. Make sure the fan
blade and pulleys are not
broken.
. Diesel engine only, check
the radiator hoses and
connections, heater hoses
and connections, radiator,
water pump, EGR cooler,
and SCR system and hoses
for leakage.
. Gasoline engine only, if the
engine coolant level in the
reserve tank is low, look for
leaks at the radiator hoses
and connections, heater
hoses and connections,
radiator, and water pump.
If the engine coolant level in
the reserve tank is at the
correct level but there is still
an indication on the
instrument panel of an
overheat condition:
You must let the engine
cool first. You may then add
engine coolant directly to
the radiator. See "Adding
Engine Coolant" under
Engine Coolant 0263. 5. Inspect to see if there is any
dirt, etc. attached to the front
surface of the radiator. Also,
inspect to see if there is
anything blocking the core.
If there is anything attached,
clean and remove it.
6. After the inspection, regardless of the vehicle condition, please
contact the nearest dealer.
Once the engine coolant
temperature gauge no longer
signals an overheat condition, you
can resume driving at a reduced
speed. Return to normal driving
after about 10 minutes if the gauge
pointer does not again show an
overheat condition.
When tap water only has been used
for engine coolant in an emergency,
change the engine coolant as soon
as possible.
Engine damage may be caused if
an overheating engine is suddenly
refilled with water. Instead, refill
slowly.
Chevrolet Low Cab Forward Owner Manual (GMNA-Localizing-U.S.-
10716700) - 2017 - crc - 12/6/16
Vehicle Care 277
Another characteristic of the HBB
system is that the brake pedal may
be depressed easily to the floor with
the vehicle at a stop. This is not a
sign of malfunction.
When the engine is running, the
system automatically charges the
accumulator whenever pressure has
been reduced after braking. Auto
charge may be activated without
braking, depending on temperature
changes in the accumulator. During
auto charge, a hissing and clicking
sound can be heard. This is not a
malfunction.
With the engine running, a booming
sound can be heard during hard
braking. This comes from the
brake-fluid pump. It is not a
malfunction.
Applying continuous hard braking
for a long time will lead to
considerable temperature rise in the
HBB pump. Such overworking of the
brakes is best avoided.Vacuum or hydraulic power
assisted brakes
If the engine stops, do not pump the
brakes. The system is designed to
stop the vehicle with reserve power
assist if the brake pedal is held
down. This reserve is greatly
reduced each time you apply and
release the brakes. If, when you
turn the steering wheel during
braking, the vehicle does not turn,
release some pressure from the
brake pedal.
In a Vehicle Equipped with a HBB,
Do Not Keep the Brake Pedal
Depressed for an Extended Period
Caution
Failure to follow the above
instruction will cause the oil inside
the HBB oil pump to get very hot.
This could damage the HBB tank
and deteriorate seals and also
could cause damage to the HBB
oil pump, HBB unit and/or HBB
hosing. Eventual leakage of HBB
(Continued)
Caution (Continued)
oil, sudden increase in brake
pedal resistance and fire could
unexpectedly result in an
accident.
Hydraulic Brake Booster (HBB)
Fluid (5500HD/5500XD Series)
The HBB system has been
designed to use ATF Dexron fluid is
used with this system, rubber
components may be damaged, oil
may leak and the system may
malfunction. It is important to
remember that the fluid used in the
hydro-booster is completely different
in characteristics from the brake
fluid used in the master and wheel
cylinders.
If hydro-booster fluid and brake fluid
from the master cylinder are
mistakenly mixed together and
used, rubber components will
deteriorate as a result of insufficient
lubrication. Any resultant oil leakage
or system malfunction can in turn
lead to dragging brakes or other
Chevrolet Low Cab Forward Owner Manual (GMNA-Localizing-U.S.-
10716700) - 2017 - crc - 12/6/16
Vehicle Care 283
Rear Axle (Gear Oil Viscosity Chart)
Gear Oil Viscosity Chart
Select appropriate gear oil in accordance with the table below. It is important
to select the viscosity appropriate for the temperature at which your vehicle
operates. Use the following table for making correct selections.
Rear Axle (Oil Level
Check)
Rear Axle Differential Gear Oil
The rear axle differential gear oil
level must be checked for its level
and it must be changed according to
the Maintenance Schedule.
Use the oil quantities indicated later
in this section only as guidelines
when changing the rear axle
differential gear oil.
After changing the oil, ensure that it
is at the correct level.
Drained oil must be disposed of in a
method conforming to the regulatory
requirements in your state.
Chevrolet Low Cab Forward Owner Manual (GMNA-Localizing-U.S.-
10716700) - 2017 - crc - 12/6/16
336 Vehicle Care
floor. Do not apply water from a
high-pressure washer nozzle
directly to the electric connectors.
Failure to observe this precaution
can lead to faulty operation of the
electrical system. If an automatic
car or truck-wash is used with
vehicles having dark or metallic
coating, the painted surfaces can be
damaged by the brushes, lose their
luster or be very noticeably
scratched.
Do not direct a large amount of
water at the air inlet openings. Do
not apply water to the engine
compartment or at electrical
components. Failure to observe this
precaution can lead to a poorly
starting and operating engine and
problems in the electrical system.
Ensure that mirrors and the antenna
are retracted before washing the
vehicle.
If an automatic car or truck-wash
must be used, avoid a
high-temperature, high pressure
type machine. Failure to observe
this precaution can lead to heat
deformation and breakage of plastic
components, or to water leaks intothe cab. When using an automatic
car or truck-wash, ensure that a
distance of at least 0.4 m
(15.75 inches) is maintained
between the nozzle and the vehicle,
and when washing door windows,
that the spray is perpendicular to
the surface of the glass.
Ensure that all detergent is fully
washed and wiped away.
Particularly in the case of strong
alkaline detergents (typically those
for industrial uses), there is a
danger that hairline cracks can
develop in lighting-cluster lenses if
the vehicle is operated without
detergent being fully wiped away.
Always read the detergent
manufacturer's instructions carefully
before use. Airborne dirt that
adheres to plastic front bumpers as
a result of rain, for example, can be
difficult to remove. In such a case,
use a commercially-available
cleaner to clean away the dirt, and
then apply a wax for use with plastic
components.Vehicle Storage
In order to maintain your vehicle's
attractive appearance as long as
possible, special consideration must
be given to its storage location.
If the vehicle is stored or kept for an
extended period of time in any of
the following locations, a chemical
change may occur in the paint work,
resulting in staining, discoloration,
rusting, and corrosion of
components.
.
Locations where a large amount
of oily matter, soot, heavy smoke
or metal powder can adhere to
the vehicle.
. Areas around pharmaceutical
plants and other facilities that
discharge chemical matter.
. Coastal areas
. Locations where a large amount
of dead bugs, bird droppings or
tree sap can adhere to the
vehicle.
Chevrolet Low Cab Forward Owner Manual (GMNA-Localizing-U.S.-
10716700) - 2017 - crc - 12/6/16
Vehicle Care 337
Polishing and Waxing
Periodic polishing and waxing is
recommended to remove built-up
residue and eliminate any
"weathered" appearance.
Your authorized dealer offers
several polishes and cleaners which
have proven value in maintaining
original finish appearance and
durability.
Painted and chrome-plated surfaces
should be waxed once or twice a
month, or whenever water is being
poorly repelled on the surfaces.
Ensure that wax is not applied in
direct sunlight, and that the
temperature of the painted surface
is no more than 40 °C (104 °F).
Always follow the instructions
provided with your wax product.
Do not use wax containing abrasive
material. Failure to observe this
precaution can lead to scratching of
painted surfaces or plastic
components.
The application of wax to rubber
component surfaces can result in
permanent whitening.Wax must not be applied to the
windshield. Failure to observe this
precaution can result in irregular
reflection of light, impairing
your view.
Protecting Exterior Bright Metal
Parts
Bright metal parts should be
cleaned regularly to keep their
luster. Washing with water is all that
is usually needed.
Use special care with aluminum
trim. To avoid damaging protective
trim, never use auto or chrome
polish, steam or caustic soap to
clean aluminum. A coating of wax,
rubbed to a high polish, is
recommended for all bright metal
parts.
Weatherstrip Lubrication
All weatherstrips should be
periodically lubricated (minimum of
every 6 months) with a silicone
grease lubricant. A thin film of
silicone grease lubricant should be
applied using a clean cloth. Silicone
grease application will lengthen
weatherstrip life, help sealing, and
assist in eliminating squeaks.
Windshield Care
Wax must not be applied to the
windshield. A layer of wax can
impair your view in rainy weather
and can also lead to rough
movements of the windshield wiper.
If engine oil or grease comes into
contact with the windshield, staining
or discoloration may result. It must
be immediately cleaned away.
If not fully cleaned by the windshield
wipers, the windshield should be
cleaned using glass cleaner. If your
windshield is not clear after using
the windshield washer, or if the
wiper blade chatters when running,
wax or other material may be on the
blade or windshield.
The windshield wipers on your truck
can be pulled out from the
windshield to provide easier access
for cleaning.
Clean the outside of the windshield
with a non-abrasive cleaner. Your
windshield is clean if beads do not
Chevrolet Low Cab Forward Owner Manual (GMNA-Localizing-U.S.-
10716700) - 2017 - crc - 12/6/16
352 Service and Maintenance
7. SPARK PLUGS :Change every
160 000 km (100,000 miles).
8. SPARK PLUG WIRES : Clean
wires and inspect for burns, cracks
or other damage. Check the wire
boot fit at the coilpack and at the
spark plugs. And replace every
160 000 km (100,000 miles).
9. FUEL TANK, CAP AND LINES :
Inspect the fuel tank, cap and lines
for damage or leaks. Remove fuel
cap, inspect gasket for an even filler
neck imprint, and any damage.
Replace parts as needed.
10. ENGINE ACCESSORY DRIVE
BELT(S) : Inspect belts. Look for
cracks, fraying, wear, and proper
tension. Adjust or replace as
needed, and change every
160 000 km (100,000 miles).
11. EVAPORATIVE CONTROL
SYSTEM (ECS) : Visually check all
fuel and vapor lines and hoses for
proper hookup, routing, and
condition. Check that bowl vent and
purge valves work properly,
if equipped. Replace as needed. 12. SHIELDS AND UNDER HOOD
INSULATION :
Inspect shields and
under hood insulation for damage or
looseness. Adjust or replace as
required.
13. AIR INTAKE SYSTEM : Check
the air intake system installation to
see that gaskets are seated
properly and all hose connections,
fasteners, and other components
are tight. Also check to be sure that
the air cleaner housing is properly
seated, that the cover fits tightly,
and the wingnut(s) is/are tight.
Tighten connections and fasteners
or replace damaged parts as
required.
14. THERMOSTATICALLY
CONTROLLED ENGINE COOLING
FAN : With the engine off and below
normal operating temperature,
check to see that the fan can be
rotated by hand on fluid coupling or
viscous drives. Replace as
necessary. 15. AUTOMATIC TRANSMISSION
FLUID :
Check the automatic transmission
fluid level at each engine oil change
and replace fluid every 84 000 km
(52,500 miles). To check the fluid
level, first set the parking brake,
then start the engine in "P" position.
With the regular brakes applied,
move the selector lever through all
the gear positions, ending with "P".
You must check the fluid level with
the engine running at slow idle and
the truck must be on a level surface.
Chevrolet Low Cab Forward Owner Manual (GMNA-Localizing-U.S.-
10716700) - 2017 - crc - 12/6/16
Index 409
Diesel Engine (cont'd)High Idle System . . . . . . . . . . . . . 174
Diesel Exhaust Fluid . . . . . . . . 30, 189
Diesel Exhaust Fluid (DEF) Gauge . . . . . . . . . . . . . . . . . . . . . . . . . 83
Diesel Exhaust Fluid (DEF) Warning Light . . . . . . . . . . . . . . . . . . 90
Diesel Particulate Filter . . . . . . . . . 180
Distracted Driving . . . . . . . . . . . . . . . 133
Dome Lamps . . . . . . . . . . . . . . . . . . . 107
Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Power Locks . . . . . . . . . . . . . . . . . . . . 39
Drive Belt Routing, Engine . . . . . . 396
Driver Behavior . . . . . . . . . . . . . . . . . 133
Driver Information
Center (DIC) . . . . . . . . . . . . . . . . . . . 93
Driving
Emergencies . . . . . . . . . . . . 148, 161
For Better Fuel Economy . . . . . . . 29
Hill and Mountain Roads . . . . . . 144
If the Vehicle is Stuck . . . . . . . . . 148
Wet Roads . . . . . . . . . . . . . . . . . . . 143
Winter . . . . . . . . . . . . . . . . . . . . . . . . 145
Driving the Vehicle . . . . . . . . . . . . . . . . 3
E
Electrical Equipment, Add-On . . . . . . . . . . . . . . . . . . . . . . . 241 Electrical System
Overload . . . . . . . . . . . . . . . . . . . . . 298
Emergencies . . . . . . . . . . . . . . 148, 161
Engine Air Cleaner/Filter . . . . . . . . . . . . . 263
Alarm and AutomaticShutdown . . . . . . . . . . . . . . . . . . . 174
Check Light (Malfunction Indicator) . . . . . . . . . . . . . . . . . . . . . . 84
Checks Before Operating . . . . . 175
Compartment Overview . . . . . . . 249
Coolant . . . . . . . . . . . . . . . . . . . . . . . 263
Coolant Temperature Gauge . . . . 82
Cover . . . . . . . . . . . . . . . . . . . . . . . . . 250
Drive Belt Routing . . . . . . . . . . . . 396
Exhaust . . . . . . . . . . . . . . . . . . . . . . 178
Heater . . . . . . . . . . . . . . . . . . . . . . . . 173
High Idle System . . . . . . . . . . . . . 174
Oil Pressure Light . . . . . . . . . . . . . . 89
Overheating . . . . . . . . . . . . . . . . . . 269
Reduced Power Light . . . . . . . . . . . 91
Running While Parked . . . . . . . . 179
Shutdown Warning Light . . . . . . . . 91
Engine Oil Level Indicator Light . . . . . . . . . . . . 90
Engines Diesel Fuel . . . . . . . . . . . . . . . . . . . 232
Exhaust Brake . . . . . . . . . . . . . . . . . . 222 Exhaust Brake Light . . . . . . . . . . . . . 88
Exhaust Fluid
Diesel . . . . . . . . . . . . . . . . . . . . . . . . 189
Extender, Seat Belt . . . . . . . . . . . . . . 55
Exterior Lamp Controls . . . . . . . . . 103
F
Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180 Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . 282
Filter, Engine Air Cleaner . . . . . . . . . . . 263
Fixed Mast Antenna . . . . . . . . . . . . 113
Flash-to-Pass . . . . . . . . . . . . . . . . . . . 104
Flashers, Hazard Warning . . . . . . 105
Flat Tire . . . . . . . . . . . . . . . . . . . . . . . . 326
Fluid Automatic Transmission . . . . . . 260
Brakes . . . . . . . . . . . . . . . . . . . . . . . . 280
Diesel Exhaust . . . . . . . . . . . . . . . . . 30
Power Steering . . . . . . . . . . . . . . . 273
Washer . . . . . . . . . . . . . . . . . . . . . . . 274
Frequency Statement Radio . . . . . . . . . . . . . . . . . . . . . . . . . 404
Front Seat Position Seats Adjustment . . . . . . . . . . . . . . . . . . . . . 44
Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 231
Biodiesel . . . . . . . . . . . . . . . . . . . . . 233
Cold Weather Operation . . . . . . 235
Diesel Engines . . . . . . . . . . . . . . . 232