2017 AUDI S4 display

Cockpit overv iew
Arrow view with route guidance started
Applies to: ve hicles w ith navigat ion system and arrow view
Depending on the vehicle equipment, the active route guidance will be displayed in the arrow view* in
the driver information system .
Fig. 19 Example: ar row view (monoc hrome instrument cluster)
Req uirement: a destination must be entered
~ page 187, route g uidance must be started and
the navigation tab mus t be disp layed.
Depending on vehicle equipment, the following
info rmation may be shown in the dr iver informa­
tion system
~ fig . 19:
(D Distance to the destinat ion or stopover
@ Distance to the next maneuve r
® Direction arrow for the upcoming maneuver
© A bar graph appears when a direct ion arrow
i s displayed . The fewer bars are shown, the
shorter the d istance is unt il the turn .
® Lane recommendation
@ Addit ional information (on -board computer)
0 Ca lcula ted arrival time
@ Disp lay of the street currently being driven
on If a point is displayed before the street , it
is indicating the street you will be o n with the
next maneuver .
The fo llowing funct ions are a lso available when
route guidance is act ive:
- Changing the voice guidance volume : turn the
right thumbwhee l up o r down during vo ice
guidance.
22
@
@
_&, WARNING
The route calculated by the nav igat ion sys tem
is a recommendation for reaching your desti ­
n ation . Obey traffic lights, stopping restric­
tions, one-way streets, lane change restric­
tions, etc.
(D Tips
- Also refer to the chapter ~ page 8, Controls
ata glance
- An exclamation point"!" in front o f the
street name indicates that the information about this street or th is section of the ro ute
is not complete in the navigat ion data con­
tained in the MMI. Obey traffic laws in one­
way streets and pedestr ian zo nes.

Head-up Display
Applies to: vehicles with Head-up Display
Fig. 20 Instrument panel : knob for the head-up display
The Head-up Display projects certain warnings or
selected information from the assist systems* or
navigation* on the windshield. The d isplay ap­
pears within the drive r's field of vision.
Switching on/off
• To switch the Head-up Display on or off, press
the knob
1;) ¢ fig . 20.
Adjusting the height
The height of the display can be adjusted to the
individual driver.
• Make sure you are seated correctly
¢ page 237.
• Turn the knob 1;) to adjust the display.
Settings in the Infotainment system
• Se lect in the Infotainment system: !MENU I but ­
ton
> Vehicle > left contro l button > Driver as­
sist
> Head-up display .
Display content
In the Infotainment system, yo u can specify
which information should be displayed: For ex­
ample, this can include navigation information*,
adaptive cruise control* or camera-based traffic
sign recognit ion* .
The display of certain information and some of the red indicator lights cannot be hidden in the
Infotainment system.
Brightness
You can adjust the display brightness in the Info­
tainment system. The display brightness decreas-
Cockpit overview
es automatically as the amount of light decreas ­
es. The background brightness is adjusted with
the instrument illumination ¢
page 54.
Picture rotation
You can rotate the picture in the Infotainment
system clockwise o r counterclockwise.
(D Note
To prevent scratches on the glass cover ing the
head-up display, do not place any objects in
the pro jection opening.
(D Tips
- Sunglasses with polarization filters and un­
favorable lighting conditions can have a
negative effect on the display .
- An opt imum disp lay depends on the seat
posi tion and the heigh t adjustment of the
head -up disp lay.
- A special windshie ld is needed for the head­
up display function.
- For information on cleaning, refer to¢
ta­
ble Interior cleaning on page 339.
23

Cockpit overview
Camera-based traffic
sign recognition
Description
Applies to: vehicles with camera-based traffic sign recogn i­
tion
F ig. 21 Instrument cluster: traffic sign recognition
Fig. 22 Windshield: camera window fo r tra ffic sign recog­
nit ion
Traffic sign recognit ion assists you when driving
by displaying detected speed limits or signs pro­
hibiting passing in the instrument cluster disp lay
~fig . 21. Within the limits of the system, the le­
gal speed limits in school zones are detected and
displayed.
General information
Traffic sign recognit ion can detect standard
speed limit signs that are within the camera's vis­
ual field. With assistance from navigation data,
detected speed limits are evaluated and shown in
the display. The traffic sign for the current de­
tected speed limit will blink in the display if you
exceed the warning threshold set in the Infotain­ ment system
~ page 2 5 .
The traffic sign recognition is subject to certain
system limitations and may be unavailable or on­
ly partially available in the following situations:
24
-when visibility is poor, such as in snow, rain,
fog or heavy spray .
-when there is glare, for example from oncom­
ing traffic or the sun.
- at high speeds.
- if the camera's visual field
~ fig. 22 is covered,
for examp le by dirt or st ickers. For info rmation
on cleaning, refer to
c::> page 33 7.
- if the traffic signs are completely or partially
covered, for examp le by trees, snow, dirt or
other vehicles.
- if speed traffic signs do not conform to the
standards.
- if traffic signs are damaged or bent.
- if traffic signs are d isplayed on sign holders
w ith electronic signs.
- if the traffic signs or the configuration of the
road have changed (navigation data is no lon­
ger up-to-date) .
.&_ WARNING
Pay attention to traffic and the area around
your vehicle when traffic sign recognition is
turned on . The traffic signs installed on the
road always take precedence over the display.
The driver is always responsible for correctly
assessing the traff ic situation.
- Under some circumstances, traffic sign rec­
ognition may not detect traffic signs cor­
rectly or detect them at all. As a result, the
system may not display the correct speed
lim it or any speed limit.
- Traff ic sign recognit ion does not adapt your
veh icle's speed to match the speed limit!
- The display in the instrument cluster is
based on the units of measurement used for
speed in that country. As a result, the dis­
play
SO in the instrument cluster can mean
eithe r km/h or mph, depending on the coun­
try.
-

Operation
Applies to: vehicles with camera -based traffic sign recogni­
tion
F ig. 23 Instr ume nt cluster: add itiona l d isplay
Accessing traffic sign recognition
.. Se lect: the f irst tab> Traffic signs .
Setting a speed warning
You set a warning thresho ld down to 15 km/ h.
The traffic s ign for the curre nt detec ted speed
limit w ill blink in the d isp lay if yo u excee d the set
thresho ld.
.,. Select in the Info tainment sys tem:
!MEN U I but­
ton >
Vehicle > left contro l bu tton > Driver as ­
s ist > Speed warning
> Traffic sign warning .
Additional display
If a v iew othe r th an the traffic sign recognition is
se lec ted in t he i nstr ument cluster d isp lay, the
speed limit w ill be shown in another disp lay
~ fig. 23. The cur rent applicable speed limit will
be shown the re, if pos sibl e w it hi n the lim its of
the system.
{t) Tips
- An a ddi tio nal i ndic a tor a pp ears in the Head­
up disp lay*.
- Y our spe ed w arning s ettin gs a re stor ed a u­
t om atica lly an d assigned to the rem ote con ­
t ro l key in us e.
Messages
Applies to: vehicles with camera-based traffic sign recogni­
tion
~ Ii Traffic sign recognition: currently unavaila­
r-1 8 ble_ Camera view restricted due to surroundings
0
~ co
Cockpit overview
Function currently unavailable. Camera view re­
stricted due to surroundings
T hi s mess age app ea rs if th e ca mera 's v is u al fiel d
is covere d~
page 24 , fig. 22 . The system will
switch itself o ff.
Ii Traffic sign recognition: currently restricted.
See owner's manual
T h is message appears if there is a mal function in
t h e nav igation system, for examp le . Th e speed
li mi t d isplay is lim ite d, w hich incr eases the r is k
of an in cor re ct displa y.
la Traffic sign based speed warning : currently
unavailable. See owner's manual
There is no wa rning when t he set t hreshold is e x­
ceeded .
No traffic sign information available
The re is no valid navig ation d ata and do speed
li mits were detec ted. Or th ere is a recommende d
s p eed but there is not a speed limit (for examp le
dr iv ing on and off the exp ressway) .
Malfunction! See owner 's manual
T he system canno t gua rantee correct funct ion
and is swi tc hed off. See an a uthoriz e d Au di deal­
er o r autho riz e d Au di Servi ce Facili ty for as sis­
t ance.
Function not available in this country
The vehicle is in a co untry where the function is
not avai lab le.
On Board Diagnostic
System (OBD)
Malfunction indicator lamp (MIL)
The malfunction ind icator lamp (MIL) ¢;j in the
i nstrument cluste r is par t of the On Board D iag­
nost ic System (O BD II) .
The ind icator light turns on when the ignition is
switched on and turns off once the engine is
sta rted and is r unning in id le at a stable speed .
T his ind icates that the MIL is f unction ing cor rec t-
~-~
25

Cockpit overview
If the light does not turn off after starting the
engine
or turns on while driving, this may indi·
cate that there is a malfunction in the eng ine. If
the indicator turns on , the catalytic converter
may be damaged.
Drive
with reduced engine performance (avoid
h ig h speeds for extended periods of time and/ or
fast acce leration) and have the malfunction cor­
rected. See an authorized Aud i dealer or author­
ized Audi Service Fac ility .
The electronic speed limiter may be faulty if the
indicator light turns on. For additional informa­
tion, refer to
¢ page 93, Electronic speed limit­
er .
The MIL indicator light may also turn on if the
fuel filler cap is not closed correctly
¢page 298.
On-Board Diagnostics
Fig . 24 Locat ion of Data Link Connector (D LC)
On-Board Diagnostics monitors the components
of your emission control system. Each monitored
component in your engine system has been as­
signed a code . In case of a malfunction, the com­
ponent w ill be identified and the fault stored as a
code in the control module memory.
The MIL light may also illuminate if there is a
leak in the on-board fuel vapor recovery system .
If the light illuminates after a refuel ing, stop the
veh icle and make sure the fue l filler cap is prop­
erly closed (on ly vehicles with gasol ine engine)
¢page 298.
In order to make an accurate d iagnosis, the stor­
ed data can only be disp layed using specia l diag­
nostic equipm ent (ge ne ric scan tool for OBD) .
26
In order to connect the special diagnostic equip­
ment, push the plug into the Data Link Connector
(DLC). The DLC is located to the r ight of the hood
release
¢ fig. 24.
Your authorized Audi dea le r or qualified work­
shop can interpret the code and perform the nec­
essary repair.
_& WARNING
Do not use the diagnostic connector for per­
sonal use. Incorrect usage can cause malfunc­
tions, which can increase the risk of a colli­
sion!
Indicator lights
Description
The indicator lights in the instrument cluster
blink or tur n on. They indicate functions or mal­
funct ions.
-
Messages may appear with some indicator lights .
A warning signal will sound at the same time.
The ind icator lights and messages in the instru­
ment cluster disp lay can be covered by other dis­
plays. To show them again, select the second tab
with the multifunction steering wheel ¢page 12.
If there are several ma lfunctions, you can display
them one at a time using the thumbwheel.
Some indicator lights in the display can display in
several colors.
& Central indicator lights
If
the . or Q indicator lig ht turns on, check
the message in the instrument cluster.
Overview
Some indicator lights turn on briefly as a function
check when you switch the ignition on. These sys ­
tems are marked with a ./ in the fo llow ing tables.
If one of these ind icator lights does not turn on,
there is a malfunction in that system.
Your vehicle has e ither a monoch rome display or
a multicolored display, depending on vehicle
equipment . Some indicator lights appear white
1111-

<( a, .... N ,....
N .... 0 0
3 a,
on a monochrome display. The. or u centra l
indicator light turns on at the same time to indi­
cate the priority of these ind icator lights.
Red indicator lights
--------------
Central indicator light
c::> page26,
Aud i pre sense*
c::> page 10 7
USA models:
Brake system ../
c::> page 29
Canada models :
Bra ke system ../
c::> page 29
USA models:
Electromecha nical parking brake
c::> page 30
Canada models:
Electromechanica l parking brake
c::> page30
Cooling system
c::> page 31
E ng ine oi l pressure
c::> page 32
Eng ine oil level
c::> page 32
Generator
c::> page 31
Safety belt
c::> page 31
Electromechanical steering../
c::> page 13 7
Steering lock
c::> page 32
E ng ine start system
c::> page32
Transmission
c::> page 87
Adapt ive cruise control*../
c::> page 98
Congestion assist*
c::> page 104 Cockpit overview
Ad B lue*
c::> page 300
Ad Blue*
c::> page 300
Yellow indicator lights
--------------
Central indicator light
c::> page 26
E lectronic Stabilization Contro l
(ESC)
c::> page 32
El ectronic Stabilization Control
(ESC) ../
c::> page 32
Electronic Stabiliza tion Control
(ESC)
c::> page 13 5
Brake system
c::> page 33
USA models:
Anti-lock braking system (ABS)../
c::> page 32
Canada models:
Anti-lock b raking system (ABS)../
c::> page 32
Safety systems ../
c::> page 33
USA models:
Brake pads
c::> page 33
Canada models:
Brake pads
c::> page 33
El ectromechanical parking brake
c::> page 30
T ire pressure
c::> page 335
Tire pressure
c::> page 335
Engine control
c::> page 33
Engine contro l (diese l engine)
c::> page 33
27

Cockpit overview
(•) Electrical system: low battery charge. Plea se
turn on ignition
The start ing ability may be impaired.
If th is message turns off after a little while , the
battery charged enough while driving.
If the message does not turn off and stay off
when dr iv ing, have an authorized Aud i dea ler or
author ized Audi Service Facility repair the mal­
function .
~ Engine oil pressure
• Turn off engine. Oil pressure too low
Stop the eng ine and do not continue driving .
Check the engine oil leve l¢
page 308 .
- If the engine oil level is too low, add engine o il
c=>page 308. Only cont inue driving once the in­
dicator light turns off.
- If the engine oil leve l is correct and the indica­
tor light st ill turns on, turn the eng ine off and
do not continue driving. See an authorized Audi
dealer or authorized Audi Service Fac ility for as­
sistance .
(D Tips
The oil pressure warning is not an o il level in­
dicator . Always check the o il level regularly .
~ Engine oil level (MIN)
• Please add oil immediately.
Add engine o il immed iate ly ¢page 308 .
l!I Please add max. x qt (l) oil. You can contin­
ue driving
Add the maximum amount of oil indicated in the
display as soon as possible
¢page 308.
~- Steering lock
• Steering : malfunction! Please stop vehicle
There is a malfunction in the elect ronic steering
lock . You cannot turn the ignition on.
32
Do not tow your vehicle because it cannot be
steered. See an authorized Audi dealer or author­
i zed Audi Service Facility for assistance.
1!11 Steering lock: malfunction! Please contact
Service
There is a malfunction in the electron ic steering
lo ck.
Drive to an authorized Audi dealer or authorized
Audi Service Facility immed iate ly to have the
malfunction corrected .
& WARNING
Do not tow your vehicle when there is a mal­
function in the electron ic steering lock -this
increases the risk of an accident .
-e Engine start system
• Engine start system: malfunction! Please
contact Service
-
Do not switch the ignition off, or you may not be
able to switch it back on.
Drive to an authorized Audi dealer or authorized
Audi Service Facility immediately to have the
malfunction corrected .
13 Engine start system: malfunction! Please
contact Service
There is a ma lfunction in the engine starting sys­
tem .
Drive to an authorized Audi dealer or authorized
Audi Service Facility immediate ly to have the
malfunction corrected.
f;. ![J Electronic Stabilization Control (ESC)
If the Ii) ind icator light blinks while driving, the
ESC or ASR (ant i-slip regu lation) is actively regu­
l ating.
If the
DJ ind icator light turns on, the system has
switched t he ESC off . In t his case, you can switch
the ignit ion off and then on to switch the ESC on
again. The indicator light turns off when the sys-
tem is functioning fu lly. .,..

,&_ WARNING
After opening the luggage com partment lid
using the emergency release in vehicles with a
fixed rear seat backrest, make s ure the brack­
et under the rea r bench seat loc ks sec urely in ­
to the mounting eyelet again.
Child safety Lock
-
The child safety lock prevents the rear doors
from being opened from the inside and the rear
power windows from be operated.
F ig. 38 Section of driver's door: co ntrols
Fi g. 39 Rear door: child safety lock
0
N
9 :::, a, a,
"'To deactivate/ac tivate the power wi ndow
switch in the rear doo rs, press the @ button in
the driver's door
r=> fig . 38. The indicator light in
the button turns on/blinks.
"' To also deactivate/activate the inner door han­
dle, open the respective rear door and turn t he
key switch w ith the mecha nical key in the d irec­
t ion of the a rrow or opposi te the d irec tion of
t h e ar row
r=> fig. 39.
Message in the instrument cluster display
(81 Childproof catch: malfunction! Please con ­
tact Service
Open ing and closing
T he re is a ma lf u nction in the c hild safety lock.
Press th e @ button again .
If the me ssage s tay s on, dr ive immedia tely to an
a uth o rized Aud i de aler o r a uth o rized Aud i Serv ice
F acility to have the ma lf u n ction repaired .
,&_ WARNING
-Always take the ve hicl e key with yo u when
leavi ng the vehicle, even for a sho rt period
of t ime. This applies part icularly when chil­
dren remain in t he vehicle. Otherwise chil­
d ren cou ld start t he e ngine o r operate elec­
tr ica l equipment (such a s power windows) ,
which inc reas es t he risk of an ac cident.
-A ma lf u nction in the ch ild safety lock cou ld
allow the rear doors to be opened from the
i n si de, which inc reases the ris k of an acc i­
d ent.
Power window
Controls
The driver can control all power windows.
Fig. 40 Drive r's door: power w indow controls
All power window switc hes are equipped with a
two-stage fu nction:
Opening and clos ing the w indows
-
"' To open or close the window comp letely, press
the switch down or pull the switch up briefly to
the second level. The operat ion will stop if the
sw itch is pressed/pulled again.
"' To select a pos it ion in between opened and
closed, p ress/p ull the switch to the first level
until the des ired w indow pos ition is reache d. ..,.
45